Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows) > Key-off Operation Function Operates even if Operating Conditions are not Satisfied

for Preparation Click here


DESCRIPTION

  1. When the front doors are closed, each power window regulator motor assembly can control its power window operation for approximately 43 seconds after the engine switch is turned from on (IG) to off by receiving operation permission signals from the main body ECU (multiplex network body ECU).
  2. However, when approximately 43 seconds have elapsed, or the driver door or front passenger door is opened within approximately 43 seconds of the engine switch being turned off, the power window regulator motor assembly stops operating.
  3. During auto operation, when 43 seconds have elapsed and key-off operation is prohibited, the power window continues operating until the auto operation is completed.

INSPECTION PROCEDURE

NOTICE:
  1. The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (Click here).
  2. If the power window regulator motor assembly (for driver door) or power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system (Click here).
  3. If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

1.CHECK MANUAL UP / DOWN FUNCTION
  1. Check that the manual up and down function using the power window regulator master switch assembly, power window regulator switch assembly and rear power window regulator switch assembly (for LH or RH door) can operate the power windows (Click here).

    OK:
    Manual up and down functions are normal.



NG
GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table) (Click here)
OK


2.CHECK REMOTE UP / DOWN FUNCTION
  1. Check that the remote up and down function using the power window regulator master switch assembly can operate all the power windows (Click here).

    OK:
    Remote up and down function is normal.



NG
GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table) (Click here)
OK


3.CHECK KEY-OFF OPERATION FUNCTION
  1. Check the key-off operation function (Click here).

    Result:

    Result
    Proceed to
    Power window can still be operated even after opening driver door or front passenger door within approximately 43 seconds of engine switch being turned off
    A
    Power window can still be operated even after approximately 43 seconds have elapsed after engine switch is turned off (for All Doors)
    B
    Power window can still be operated even after approximately 43 seconds have elapsed after engine switch is turned off (for Driver Door or Front Passenger Door)
    C
    Power window can still be operated even after approximately 43 seconds have elapsed after engine switch is turned off (for Rear LH Door or Rear RH Door)
    D



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

C
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR) (Click here)

D
Go to step 5
A


4.READ VALUE USING GTS (MAIN BODY)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Courtesy SW
    Front door courtesy light switch RH / OFF or ON
    OFF: Front door RH closed
    ON: Front door RH open
    -
    FL Door Courtesy SW
    Front door courtesy light switch LH / OFF or ON
    OFF: Front door LH closed
    ON: Front door LH open
    -

    OK:
    On the GTS screen, ON or OFF is displayed accordingly.



NG
GO TO LIGHTING SYSTEM (Proceed to Front Door Courtesy Switch Circuit) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
  1. Replace the main body ECU (multiplex network body ECU) (Click here).


NEXT


6.CHECK KEY-OFF OPERATION FUNCTION
  1. Check the key-off operation function (Click here).

    OK:
    Key-off operation function is normal.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)