Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Interior Light Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:
  1. Personal Light*2, *3
  2. Rear Interior Light
  3. Ignition Key Cylinder Light*1

HINT:
The light cut relay supplies power to the lights not controlled by the illuminated entry system. If all the lights that use power from the light cut relay do not turn on, check the light cut relay circuit first (Click here).

  1. *1: w/o Smart Entry and Start System
  2. *2: for TMC, TMMR Made
  3. *3: for TMMK Made (w/ Sliding Roof)

WIRING DIAGRAM


E230716E07


E315468E01


E315469E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Illuminated Entry System
    Personal light*1, *2 and rear interior light
    ON/OFF
    1. No. 1 room light switch in DOOR position*3
    2. Interior light door switch is on*1, *2

    1. *1: for TMC, TMMR Made
    2. *2: for TMMK Made (w/ Sliding Roof)
    3. *3: for TMMK Made (w/o Sliding Roof)

    OK:
    Each light fades in.


Result:

Result
Proceed to
OK
A
NG (w/o Smart Entry and Start System)*1
B
NG (w/ Smart Entry and Start System)*1, *2
C
NG (w/ Smart Entry and Start System)*3
D

  1. *1: for TMC, TMMR Made
  2. *2: for TMMK Made (w/ Sliding Roof)
  3. *3: for TMMK Made (w/o Sliding Roof)


B
Go to step 2

C
Go to step 10

D
Go to step 15
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Perform the check under the following condition:
    1. Interior light door switch on
    2. Personal light switch off

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3B-34 - Body ground
    Always
    11 to 14 V
    3B-35 - Body ground
    Always
    11 to 14 V


    Result:

    Result
    Proceed to
    OK
    A
    NG (Voltage is not present at terminal 3B-34)
    B
    NG (Voltage is not present at terminal 3B-35)
    C



B
Go to step 4

C
Go to step 7
A


3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E173026E06


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-34 - MB-1 (ILE)
    Always
    Below 1 Ω
    3B-35 - MB-1 (ILE)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

4.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - TRANSPONDER KEY COIL)
  1. Disconnect the I191 transponder key coil connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I191-2 (ILL+) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT TRANSPONDER KEY COIL
  1. Remove the transponder key coil (Click here).

  1. Inspect the transponder key coil (Click here).

    OK:
    Transponder key coil is normal.



NG
REPLACE TRANSPONDER KEY COIL (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY COIL - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I191-4 (ILL-) - 3B-34
    Always
    Below 1 Ω
    I191-4 (ILL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - ROOF CONSOLE BOX ASSEMBLY)
  1. Disconnect the S7 roof console box assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S7-9 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT ROOF CONSOLE BOX ASSEMBLY
  1. Remove the roof console box assembly (Click here).

  1. Inspect the roof console box assembly (Click here).

    OK:
    Roof console box assembly is normal.



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S7-6 (CTY) - 3B-35
    Always
    Below 1 Ω
    S7-6 (CTY) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

USE SIMULATION METHOD TO CHECK (Click here)  

10.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Perform the check under the following conditions:
    1. Interior light door switch on
    2. Personal light switch off

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3B-35 - Body ground
    Always
    11 to 14 V



NG
Go to step 12
OK


11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E173026E06


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-35 - MB-1 (ILE)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

12.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - ROOF CONSOLE BOX ASSEMBLY)
  1. Disconnect the S7*1, S14*2 roof console box assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S7-9 (B) - Body ground*1
    Always
    11 to 14 V
    S14-9 (B) - Body ground*2
    Always
    11 to 14 V

  1. *1: for TMC, TMMR Made
  2. *2: for TMMK Made


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.INSPECT ROOF CONSOLE BOX ASSEMBLY
  1. Remove the roof console box assembly (for TMC, TMMR Made) (Click here).

  1. Remove the roof console box assembly (for TMMK Made) (Click here).

  1. Inspect the roof console box assembly (for TMMK Made) (Click here).

  1. Inspect the roof console box assembly (for TMC, TMMR Made) (Click here).

    OK:
    Roof console box assembly is normal.


Result:

Result
Proceed to
OK
A
NG (for TMC, TMMR Made)
B
NG (for TMMK Made)
C



B
REPLACE ROOF CONSOLE BOX ASSEMBLY (Click here)

C
REPLACE ROOF CONSOLE BOX ASSEMBLY (Click here)
A


14.CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S7-6 (CTY) - 3B-35*1
    Always
    Below 1 Ω
    S14-6 (CTY) - 3B-35*2
    Always
    Below 1 Ω
    S7-6 (CTY) - Body ground*1
    Always
    10 kΩ or higher
    S14-6 (CTY) - Body ground*2
    Always
    10 kΩ or higher

  1. *1: for TMC, TMMR Made
  2. *2: for TMMK Made


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

USE SIMULATION METHOD TO CHECK (Click here)  

15.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    Perform the check under the following condition:
    1. No. 1 room light switch in DOOR position

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    3B-35 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E173026E06


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-35 - MB-1 (ILE)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)