LIGHTING SYSTEM > Interior Light Circuit |



| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Illuminated Entry System | Personal light*1, *2 and rear interior light | ON/OFF |
|
| Result | Proceed to |
| OK | A |
| NG (w/o Smart Entry and Start System)*1 | B |
| NG (w/ Smart Entry and Start System)*1, *2 | C |
| NG (w/ Smart Entry and Start System)*3 | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Disconnect the 3B instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3B-34 - Body ground | Always | 11 to 14 V |
| 3B-35 - Body ground | Always | 11 to 14 V |
| Result | Proceed to |
| OK | A |
| NG (Voltage is not present at terminal 3B-34) | B |
| NG (Voltage is not present at terminal 3B-35) | C |
|
| ||||
|
| ||||
| A | |
| 3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Remove the instrument panel junction block assembly (Click here).
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.

| *a | Component without harness connected (Instrument Panel Junction Block Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
| 3B-34 - MB-1 (ILE) | Always | Below 1 Ω |
| 3B-35 - MB-1 (ILE) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - TRANSPONDER KEY COIL) |
Disconnect the I191 transponder key coil connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I191-2 (ILL+) - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 5.INSPECT TRANSPONDER KEY COIL |
Remove the transponder key coil (Click here).
Inspect the transponder key coil (Click here).
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY COIL - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I191-4 (ILL-) - 3B-34 | Always | Below 1 Ω |
| I191-4 (ILL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - ROOF CONSOLE BOX ASSEMBLY) |
Disconnect the S7 roof console box assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S7-9 (B) - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 8.INSPECT ROOF CONSOLE BOX ASSEMBLY |
Remove the roof console box assembly (Click here).
Inspect the roof console box assembly (Click here).
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S7-6 (CTY) - 3B-35 | Always | Below 1 Ω |
| S7-6 (CTY) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Disconnect the 3B instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3B-35 - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 11.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Remove the instrument panel junction block assembly (Click here).
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.

| *a | Component without harness connected (Instrument Panel Junction Block Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
| 3B-35 - MB-1 (ILE) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 12.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - ROOF CONSOLE BOX ASSEMBLY) |
Disconnect the S7*1, S14*2 roof console box assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S7-9 (B) - Body ground*1 | Always | 11 to 14 V |
| S14-9 (B) - Body ground*2 | Always | 11 to 14 V |
|
| ||||
| OK | |
| 13.INSPECT ROOF CONSOLE BOX ASSEMBLY |
Remove the roof console box assembly (for TMC, TMMR Made) (Click here).
Remove the roof console box assembly (for TMMK Made) (Click here).
Inspect the roof console box assembly (for TMMK Made) (Click here).
Inspect the roof console box assembly (for TMC, TMMR Made) (Click here).
| Result | Proceed to |
| OK | A |
| NG (for TMC, TMMR Made) | B |
| NG (for TMMK Made) | C |
|
| ||||
|
| ||||
| A | |
| 14.CHECK HARNESS AND CONNECTOR (ROOF CONSOLE BOX ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S7-6 (CTY) - 3B-35*1 | Always | Below 1 Ω |
| S14-6 (CTY) - 3B-35*2 | Always | Below 1 Ω |
| S7-6 (CTY) - Body ground*1 | Always | 10 kΩ or higher |
| S14-6 (CTY) - Body ground*2 | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 15.CHECK HARNESS AND CONNECTOR (LIGHT CUT RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Disconnect the 3B instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3B-35 - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 16.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Remove the instrument panel junction block assembly (Click here).
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.

| *a | Component without harness connected (Instrument Panel Junction Block Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
| 3B-35 - MB-1 (ILE) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||