FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > Wireless Transmitter Memory Function does not Operate |
| 1.CHECK POWER DOOR LOCK CONTROL SYSTEM |
Check the manual lock/unlock function by using the door control switch (multiplex network master switch assembly) (Click here).
|
| ||||
| OK | |
| 2.CHECK SMART ENTRY AND START SYSTEM (for Start Function) |
Check that the engine starts normally when the engine switch is pressed while carrying the key and while the brake pedal is depressed.
|
| ||||
| OK | |
| 3.CHECK SEAT POSITION MEMORY FUNCTION |
Store a seat position in memory (Click here).
Check that the buzzer sounds for 0.5 seconds to indicate that a position has been stored.
|
| ||||
| OK | |
| 4.CHECK SEAT POSITION RESTORING FUNCTION |
Restore a memorized seat position (Click here).
Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.
|
| ||||
| OK | |
| 5.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Connection | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Door Courtesy | Front door courtesy light switch assembly signal / OPEN or CLOSE | OPEN: Driver door open CLOSE: Driver door closed | - |
|
| ||||
| OK | |
| 6.CHECK MEMORY CALL REGISTRATION FUNCTION |
When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.
Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration (Click here).
|
| ||||
| OK | |
| 7.READ VALUE USING GTS (MEMORY CALL REGISTRATION) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Mem SW No. w/KeyID1 | Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID1 MEM SW1: M1 switch linked with key ID1 MEM SW2: M2 switch linked with key ID1 MEM SW3: M3 switch linked with key ID1* | - |
| Mem SW No. w/KeyID2 | Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID2 MEM SW1: M1 switch linked with key ID2 MEM SW2: M2 switch linked with key ID2 MEM SW3: M3 switch linked with key ID2* | - |
| Mem SW No. w/KeyID3 | Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID3 MEM SW1: M1 switch linked with key ID3 MEM SW2: M2 switch linked with key ID3 MEM SW3: M3 switch linked with key ID3* | - |
| Mem SW No. w/KeyID4 | Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID4 MEM SW1: M1 switch linked with key ID4 MEM SW2: M2 switch linked with key ID4 MEM SW3: M3 switch linked with key ID4* | - |
| Mem SW No. w/KeyID5 | Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID5 MEM SW1: M1 switch linked with key ID5 MEM SW2: M2 switch linked with key ID5 MEM SW3: M3 switch linked with key ID5* | - |
| Mem SW No. w/KeyID6 | Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID6 MEM SW1: M1 switch linked with key ID6 MEM SW2: M2 switch linked with key ID6 MEM SW3: M3 switch linked with key ID6* | - |
| Mem SW No. w/KeyID7 | Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID7 MEM SW1: M1 switch linked with key ID7 MEM SW2: M2 switch linked with key ID7 MEM SW3: M3 switch linked with key ID7* | - |
|
| ||||
| OK | |
| 8.CHECK MEMORY CALL FUNCTION |
Turn the engine switch off.
Close and lock all doors.
Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.
Open the driver door and check that the driver seat moves to the memorized position (Click here).
|
| ||||
| OK | ||
| ||
| 9.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
Replace the main body ECU (multiplex network body ECU) (Click here).
| NEXT | |
| 10.CHECK MEMORY CALL REGISTRATION FUNCTION |
When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.
Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration (Click here).
|
| ||||
| OK | ||
| ||
| 11.REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) |
Replace the front power seat switch LH (w/ Memory) (Click here).
| NEXT | |
| 12.CHECK MEMORY CALL REGISTRATION FUNCTION |
When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.
Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration (Click here).
|
| ||||
| OK | ||
| ||