Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > Wireless-linked Return Function does not Operate

for Preparation Click here


DESCRIPTION

When a door is unlocked using the wireless unlock function or entry unlock function, the certification ECU (smart key ECU assembly) sends a door unlock signal and key ID signal to the main body ECU (multiplex network body ECU). When the main body ECU (multiplex network body ECU) receives the door unlock signal, it stores the key ID. When the driver door is opened, the memory call and memory command information of the stored key ID is sent to each driving position related control ECU. Each control ECU receives the memory commands and performs the memory call operation according to predetermined control timing values.

INSPECTION PROCEDURE

NOTICE:
The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (Click here).

1.CHECK FRONT POWER SEAT CONTROL SYSTEM
  1. Check the operation of the power seats (Click here).

  1. Check whether seat positions can be stored in memory (Click here).

  1. Check whether seat positions can be restored (Click here).

  1. Check the operation of memory call registration (Click here).

    Result:
    Result
    Proceed to
    OK
    A
    NG (power seat operation)
    B
    NG (seat position memory)
    C
    NG (seat position restoring)
    D
    NG (memory call registration)
    E



B
GO TO PROBLEM SYMPTOMS TABLE (Click here)

C
GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized) (Click here)

D
GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat does not Return to Memorized Position) (Click here)

E
GO TO OTHER DIAGNOSIS PROCEDURE (Wireless Transmitter Memory Function does not Operate) (Click here)
A


2.CHECK MEMORY CALL FUNCTION (WIRELESS UNLOCK OR ENTRY UNLOCK)
  1. Turn the engine switch off.

  1. Close and lock all doors.

  1. Unlock the driver door by pressing the unlock switch of the memory call registered key (wireless unlock function).

  1. Unlock the driver door by touching the driver door outside handle while holding the memory call registered key (entry unlock function).

  1. Open the driver door and check that the driver seat moves to the memorized position.

    Result:
    Result
    Proceed to
    Memory call function linked with the wireless unlock function does not operate.
    A
    Memory call function linked with the entry unlock function does not operate.
    B
    Both memory call function linked with the wireless unlock function and entry unlock function do not operate.
    C



B
Go to step 9

C
Go to step 15
A


3.CHECK WIRELESS UNLOCK FUNCTION
  1. Check the wireless unlock function (Click here).

    OK:
    Wireless unlock function is normal.



NG
GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (Click here)
OK


4.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)
  1. Use the memory call function and check the outer mirror operation (Click here).

    Result:
    Result
    Proceed to
    Outer mirrors operate normally
    A
    Outer mirrors do not operate normally
    B



B
Go to step 7
A


5.REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY)
  1. Replace the front power seat switch LH (w/ Memory) (Click here).


NEXT


6.CHECK MEMORY CALL FUNCTION
  1. Store a seat position in memory (Click here).

  1. Perform memory call registration (Click here).

  1. Turn the engine switch off.

  1. Close and lock all doors.

  1. Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.

  1. Open the driver door and check that the driver seat moves to the memorized position (Click here).

    OK:
    Driver seat moves to the memorized position.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (FRONT POWER SEAT SWITCH LH (W/ MEMORY) WAS DEFECTIVE) 

7.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
  1. Replace the main body ECU (multiplex network body ECU) (Click here).


NEXT


8.CHECK MEMORY CALL FUNCTION
  1. Store a seat position in memory (Click here).

  1. Perform memory call registration (Click here).

  1. Turn the engine switch off.

  1. Close and lock all doors.

  1. Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.

  1. Open the driver door and check that the driver seat moves to the memorized position (Click here).

    OK:
    Driver seat moves to the memorized position.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE) 

9.CHECK SMART ENTRY AND START SYSTEM (ENTRY UNLOCK FUNCTION)
  1. Check the entry unlock function of the smart entry and start system (Click here).

    OK:
    Entry unlock function is normal.



NG
GO TO SMART ENTRY AND START SYSTEM (for Entry Function) (Click here)
OK


10.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)
  1. Use the memory call function and check the outer mirror operation (Click here).

    Result:
    Result
    Proceed to
    Outer mirrors operate normally
    A
    Outer mirrors do not operate normally
    B



B
Go to step 13
A


11.REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY)
  1. Replace the front power seat switch LH (w/ Memory) (Click here).


NEXT


12.CHECK MEMORY CALL FUNCTION
  1. Store a seat position in memory (Click here).

  1. Perform memory call registration (Click here).

  1. Turn the engine switch off.

  1. Close and lock all doors.

  1. Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.

  1. Open the driver door and check that the driver seat moves to the memorized position (Click here).

    OK:
    Driver seat moves to the memorized position.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (FRONT POWER SEAT SWITCH LH (W/ MEMORY) WAS DEFECTIVE) 

13.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
  1. Replace the main body ECU (multiplex network body ECU) (Click here).


NEXT


14.CHECK MEMORY CALL FUNCTION
  1. Store a seat position in memory (Click here).

  1. Perform memory call registration (Click here).

  1. Turn the engine switch off.

  1. Close and lock all doors.

  1. Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.

  1. Open the driver door and check that the driver seat moves to the memorized position (Click here).

    OK:
    Driver seat moves to the memorized position.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE) 

15.CHECK MEMORY CALL FUNCTION (MIRROR OPERATION)
  1. Use the memory call function and check the outer mirror operation (Click here).

    Result:
    Result
    Proceed to
    Outer mirrors operate normally
    A
    Outer mirrors do not operate normally
    B



B
Go to step 18
A


16.REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY)
  1. Replace the front power seat switch LH (w/ Memory) (Click here).


NEXT


17.CHECK MEMORY CALL FUNCTION
  1. Store a seat position in memory (Click here).

  1. Perform memory call registration (Click here).

  1. Turn the engine switch off.

  1. Close and lock all doors.

  1. Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.

  1. Open the driver door and check that the driver seat moves to the memorized position (Click here).

    OK:
    Driver seat moves to the memorized position.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (FRONT POWER SEAT SWITCH LH (W/ MEMORY) WAS DEFECTIVE) 

18.READ VALUE USING GTS (MEMORY CALL REGISTRATION)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mem SW No. w/KeyID1
    Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID1
    MEM SW1: M1 switch linked with key ID1
    MEM SW2: M2 switch linked with key ID1
    MEM SW3: M3 switch linked with key ID1*
    -
    Mem SW No. w/KeyID2
    Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID2
    MEM SW1: M1 switch linked with key ID2
    MEM SW2: M2 switch linked with key ID2
    MEM SW3: M3 switch linked with key ID2*
    -
    Mem SW No. w/KeyID3
    Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID3
    MEM SW1: M1 switch linked with key ID3
    MEM SW2: M2 switch linked with key ID3
    MEM SW3: M3 switch linked with key ID3*
    -
    Mem SW No. w/KeyID4
    Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID4
    MEM SW1: M1 switch linked with key ID4
    MEM SW2: M2 switch linked with key ID4
    MEM SW3: M3 switch linked with key ID4*
    -
    Mem SW No. w/KeyID5
    Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID5
    MEM SW1: M1 switch linked with key ID5
    MEM SW2: M2 switch linked with key ID5
    MEM SW3: M3 switch linked with key ID5*
    -
    Mem SW No. w/KeyID6
    Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID6
    MEM SW1: M1 switch linked with key ID6
    MEM SW2: M2 switch linked with key ID6
    MEM SW3: M3 switch linked with key ID6*
    -
    Mem SW No. w/KeyID7
    Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3*
    NONE: No switches linked with key ID7
    MEM SW1: M1 switch linked with key ID7
    MEM SW2: M2 switch linked with key ID7
    MEM SW3: M3 switch linked with key ID7*
    -

  1. *: Although the item is displayed on the GTS, it is not applicable to this vehicle.
  1. Enter the following menus: Body / Driver Seat / Data List.

  1. Read the Data List according to the display on the GTS.

    Driver Seat (Front Power Seat Switch LH (w/ Memory)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Seat Memory No1
    Seat position memorized with M1 switch / Mem or Not Mem
    Mem: Memorized
    Not Mem: Not memorized
    -
    Seat Memory No2
    Seat position memorized with M2 switch / Mem or Not Mem
    Mem: Memorized
    Not Mem: Not memorized
    -

    OK:
    On the GTS display, it is confirmed that the memory switch which is linked with a key ID has a memorized seat position. (For example, on the GTS display, "Mem SW No. w/KeyID1" displays "MEM SW1" and "Seat Memory No1" displays "Mem".)



NG
PERFORM MEMORY CALL REGISTRATION (Click here)
OK


19.READ VALUE USING GTS (DRIVER DOOR COURTESY SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Connection
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Courtesy
    Front door courtesy light switch assembly signal / OPEN or CLOSE
    OPEN: Driver door open
    CLOSE: Driver door closed
    -

    OK:
    On the GTS screen, each item changes between ON and OFF according to the above.



NG
GO TO LIGHTING SYSTEM (Front Door Courtesy Switch Circuit) (Click here)
OK


20.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
  1. Replace the main body ECU (multiplex network body ECU) (Click here).


NEXT


21.CHECK MEMORY CALL FUNCTION
  1. Store a seat position in memory (Click here).

  1. Perform memory call registration (Click here).

  1. Turn the engine switch off.

  1. Close and lock all doors.

  1. Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.

  1. Open the driver door and check that the driver seat moves to the memorized position (Click here).

    OK:
    Driver seat moves to the memorized position.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)