Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speed Signal Circuit

for Preparation Click here


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the brake actuator assembly (skid control ECU) which uses this information to create the vehicle speed sensor signal*a. The vehicle speed sensor signal consists of pulses sent to the combination meter assembly from the brake actuator assembly (skid control ECU). To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the brake actuator assembly (skid control ECU). The pulse signal is created by switching the transistor in the brake actuator assembly (skid control ECU) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the brake actuator assembly (skid control ECU). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on the pulse signal.
  1. *a: This vehicle speed sensor signal is created by the brake actuator assembly (skid control ECU). There is no actual component that is referred to as the vehicle speed sensor. In addition, for some other systems, vehicle speed information may be exchanged using CAN communication.

HINT:
This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM


for 2GR-FE

E360831E01


for 2AR-FE

E364914E01


for 6AR-FSE

E360832E01


INSPECTION PROCEDURE

1.INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)


    E224284E38
  1. Disconnect the I18 combination meter assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I18-3 (+S) - Body ground
    Ignition switch ON
    4.5 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)

    HINT:
    If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



NG
Go to step 5
OK


2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
  1. Reconnect the I18 combination meter assembly connector.



    C238832E09
  1. Disconnect the A49 brake actuator assembly (skid control ECU) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A49-2 (SP1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly (Skid Control ECU))



NG
Go to step 4
OK


3.INSPECT BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (INPUT WAVEFORM)


    E204779E51
  1. Check the input waveform.

    1. Reconnect the A49 brake actuator assembly (skid control ECU) connector.

    2. Remove the combination meter assembly with the connector(s) still connected.

    3. Connect an oscilloscope to terminal I18-4 (SI) and body ground.

    4. Turn the ignition switch to ON.

    5. Turn the wheel slowly.

    6. Check the signal waveform according to the condition(s) in the table below.
      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms/DIV.
      Vehicle condition
      Ignition switch ON, wheel being rotated
      Text in Illustration 
      *a
      Component with harness connected
      (Combination Meter Assembly)

      OK:
      The waveform is displayed as shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)  

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU))
  1. Disconnect the I18 combination meter assembly and A49 brake actuator assembly (skid control ECU) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A49-2 (SP1) - I18-4 (SI)
    Always
    Below 1 Ω
    A49-2 (SP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
  1. Disconnect the I124 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-3 (+S) - I124-18
    Always
    Below 1 Ω
    I18-3 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)
  1. Check for a short in the circuit that is connected to the junction connector shown in the wiring diagram.

    HINT:
    If voltage is not present, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.

    1. Disconnect the I124 junction connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      I124-21 - Body ground
      Ignition switch ON
      4.5 to 14 V
      I124-19 - Body ground
      Ignition switch ON
      4.5 to 14 V
      I124-20 - Body ground
      Ignition switch ON
      4.5 to 14 V
      I124-22 - Body ground
      Ignition switch ON
      4.5 to 14 V
      I124-16 - Body ground
      Ignition switch ON
      4.5 to 14 V
      I124-17 - Body ground
      Ignition switch ON
      4.5 to 14 V

      Result:
      Result
      Proceed to
      Voltage is not present in one circuit.
      A
      Voltage is present in all the circuits.
      B



B
REPLACE JUNCTION CONNECTOR (INSTRUMENT PANEL WIRE)
A


7.SYSTEM CHECK
  1. Select the circuit for which voltage was not present in step 6.

    Result:

    Tester Connection
    System that uses the circuit
    Proceed to
    I124-21 - Body ground
    Smart entry and start system*1
    A
    I124-19 - Body ground
    Navigation system*2
    B
    I124-20 - Body ground
    Auto wiper system*3
    C
    I124-22 - Body ground
    Telematics System*4
    D
    I124-16 - Body ground
    SFI system, Automatic headlight beam level control system*8, U660E automatic transaxle system*5
    E
    I124-17 - Body ground
    Audio and visual system*7 or Navigation system*6

    1. *1: w/ Smart Entry and Start System
    2. *2: for 10 Speakers
    3. *3: w/ Auto Wiper System
    4. *4: w/ Manual (SOS) Switch
    5. *5: for 2GR-FE
    6. *6: for Navigation Receiver Type
    7. *7: for Radio and Display Type
    8. *8: w/ Automatic Headlight Beam Level Control System



B
Go to step 9

C
Go to step 10

D
Go to step 22

E
Go to step 11
A


8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) CIRCUIT)
  1. Disconnect the I78 certification ECU (Smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I78-27 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY CIRCUIT)
  1. Disconnect the I69 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I69-11 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)  

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY CIRCUIT)
  1. Disconnect the I72 windshield wiper relay assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I72-24 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY (Click here)  

11.SYSTEM CHECK
  1. Select the circuit for which voltage was not present in step 6.

    Result:

    Tester Connection
    System that uses the circuit
    Proceed to
    I124-16 - Body ground
    SFI system, Automatic headlight beam level control system*4, U660E automatic transaxle system*1
    A
    I124-17 - Body ground
    Audio and visual system*3 or Navigation system*2
    B

    1. *1: for 2GR-FE
    2. *2: for Navigation Receiver Type
    3. *3: for Radio and Display Type
    4. *4: w/ Automatic Headlight Beam Level Control System



B
Go to step 19
A


12.CONFIRM VEHICLE TYPE
  1. Choose the model to be inspected.

    Result:
    Result
    Proceed to
    for 2GR-FE
    A
    for 2AR-FE
    B
    for 6AR-FSE
    C



B
Go to step 16

C
Go to step 18
A


13.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - EACH ECU)
  1. Disconnect the A25 ECM connector.

  1. Disconnect the E7 TCM connector.

  1. Disconnect the A34 headlight leveling ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I124-16 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.INSPECT ECM (SHORT CIRCUIT IN ECM)
  1. Reconnect the E7 TCM connector.

  1. Reconnect the A34 headlight leveling ECU assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I124-16 - Body ground
    Ignition switch ON
    4.5 to 14 V

    HINT:
    If the result is as specified, there may be a short circuit in the ECM.



NG
Go to step 15
OK

REPLACE ECM (Click here)  

15.INSPECT TCM (SHORT CIRCUIT IN TCM)
  1. Reconnect the A25 ECM connector.

  1. Disconnect the E7 TCM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I124-16 - Body ground
    Ignition switch ON
    4.5 to 14 V

    HINT:
    If the result is as specified, there may be a short circuit in the TCM.



NG
REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)
OK

REPLACE TCM (Click here)  

16.CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR - EACH ECU)
  1. Disconnect the A25 ECM connector.

  1. Disconnect the A34 headlight leveling ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I124-16 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17.INSPECT ECM (SHORT CIRCUIT IN ECM)
  1. Reconnect the A34 headlight leveling ECU assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I124-16 - Body ground
    Ignition switch ON
    4.5 to 14 V

    HINT:
    If the result is as specified, there may be a short circuit in the ECM.



NG
REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)  

18.CHECK HARNESS AND CONNECTOR (ECM CIRCUIT)
  1. Disconnect the A84 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A84-44 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

19.CONFIRM VEHICLE TYPE
  1. Choose the model to be inspected.

    Result:
    Result
    Proceed to
    except TMMK Made
    A
    for TMMK Made
    B



B
Go to step 21
A


20.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY CIRCUIT, RADIO AND DISPLAY RECEIVER ASSEMBLY CIRCUIT, RADIO RECEIVER ASSEMBLY CIRCUIT)
  1. Disconnect the I67 navigation receiver assembly*1 connector, I155 radio and display receiver assembly*2 connector or I150 radio receiver assembly*3 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-17 (SPD)*1 - Body ground
    Always
    10 kΩ or higher
    I155-17 (SPD)*2 - Body ground
    Always
    10 kΩ or higher
    I150-17 (SPD)*3 - Body ground
    Always
    10 kΩ or higher

    1. *1: for Navigation Receiver Type
    2. *2: for Radio and Display Type
    3. *3: for Radio Receiver Type

    Result:
    Result
    Proceed to
    OK (for Navigation Receiver Type)
    A
    OK (for Radio and Display Type)
    B
    OK (for Radio Receiver Type)
    C
    NG
    D



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPLACE RADIO RECEIVER ASSEMBLY (Click here)

D
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

21.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY CIRCUIT, RADIO AND DISPLAY RECEIVER ASSEMBLY CIRCUIT)
  1. Disconnect the I67 navigation receiver assembly*1 connector or I155 radio and display receiver assembly*2 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-17 (SPD)*1 - Body ground
    Always
    10 kΩ or higher
    I155-17 (SPD)*2 - Body ground
    Always
    10 kΩ or higher

    1. *1: for Navigation Receiver Type
    2. *2: for Radio and Display Type

    Result:
    Result
    Proceed to
    OK (for Navigation Receiver Type)
    A
    OK (for Radio and Display Type)
    B
    NG
    C



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

22.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER CIRCUIT)
  1. Disconnect the I218 telematics transceiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I218-10 (SPD) - Body ground
    Always
    10 kΩ or higher



B
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE TELEMATICS TRANSCEIVER (Click here)