ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System) > Immobiliser System does not Operate Properly |
| 1.CHECK FOR DTC |
Check for DTCs (Click here).
| Result | Proceed to |
| DTCs are not output | A |
| DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER FUEL CUT) |
for 2GR-FE or 2AR-FE
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Immobiliser Fuel Cut | Status of immobiliser fuel cut / ON or OFF | - | - |
for 6AR-FSE
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Immobiliser Fuel Cut Status | Status of immobiliser fuel cut / ON or OFF | - | - |
| Result | Proceed to |
| NG | A |
| OK (for 2GR-FE) | B |
| OK (for 2AR-FE) | C |
| OK (for 6AR-FSE) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK WHETHER ENGINE STARTS |
Check that the engine starts 5 seconds after the engine switch turned on (IG).
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 4.SYSTEM CHECK |
Check the vehicle specification.
| Result | Proceed to |
| w/o Entry Function on Driver Door or for TMMK Made | A |
| w/ Entry Function on Driver Door except TMMK Made | B |
|
| ||||
| A | |
| 5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM) |
Disconnect the A43 certification ECU (smart key ECU assembly) connector.
Disconnect the A25*1 or A84*2 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A43-14 (EFII) - A25-29 (IMO) | Always | Below 1 Ω |
| A43-14 (EFII) or A25-29 (IMO) - Body ground | Always | 10 kΩ or higher |
| A43-13 (EFIO) - A25-28 (IMI) | Always | Below 1 Ω |
| A43-13 (EFIO) or A25-28 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A43-14 (EFII) - A84-45 (IMO) | Always | Below 1 Ω |
| A43-14 (EFII) or A84-45 (IMO) - Body ground | Always | 10 kΩ or higher |
| A43-13 (EFIO) - A45-28 (IMI) | Always | Below 1 Ω |
| A43-13 (EFIO) or A45-28 (IMI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT ECM (TERMINAL IMI AND IMO) |
Reconnect the A43 certification ECU (smart key ECU assembly) connector.
Reconnect the A25*1 or A84*2 ECM connector.
Using an oscilloscope, check the waveform.

| *A | for 2AR-FE | *B | for 6AR-FSE |
| *a | Component with harness connected (ECM) | *b | Approximately 160 ms |
| *c | Approximately 270 ms | *d | Approximately 40 ms |
| *e | Approximately 60 ms | *f | Waveform 1 |
| *g | Waveform 2 | *h | Waveform 3 |
| *i | Waveform 1 (detail) | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
| A25-29 (IMO) - Body ground | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | 2 V/DIV., 500 ms./DIV. | Pulse generation (See waveform 2) |
| A25-28 (IMI) - Body ground | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | 2 V/DIV., 500 ms./DIV. | Pulse generation (See waveform 1 and 3) |
| Tester Connection | Condition | Tool Setting | Specified Condition |
| A84-45 (IMO) - Body ground | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | 2 V/DIV., 500 ms./DIV. | Pulse generation (See waveform 2) |
| A45-28 (IMI) - Body ground | Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected | 2 V/DIV., 500 ms./DIV. | Pulse generation (See waveform 1 and 3) |
| Result | Proceed to |
| Normal waveform | A |
| Waveform 1 or 3 not output, or has abnormal wavelength or shape | B |
| Waveform 2 not output, or has abnormal wavelength or shape (for 2AR-FE) | C |
| Waveform 2 not output, or has abnormal wavelength or shape (for 6AR-FSE) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 7.REGISTER ECU COMMUNICATION ID |
Register the ECU communication ID.
| NEXT | |
| 8.CHECK WHETHER ENGINE STARTS |
Check that the engine starts.
|
| ||||
| OK | ||
| ||
| 9.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Replace the certification ECU (smart key ECU assembly) with a new one.
| NEXT | |
| 10.REGISTER ECU COMMUNICATION ID |
Register the ECU communication ID.
| NEXT | |
| 11.CHECK WHETHER ENGINE STARTS |
Check that the engine starts.
| Result | Proceed to |
| OK | A |
| NG (for 2AR-FE) | B |
| NG (for 6AR-FSE) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 12.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM) |
Disconnect the I20 ID code box (immobiliser code ECU) connector.
Disconnect the A25 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I20-3 (EFII) - A25-30 (IMO) | Always | Below 1 Ω |
| I20-3 (EFII) or A25-30 (IMO) - Body ground | Always | 10 kΩ or higher |
| I20-4 (EFIO) - A25-31 (IMI) | Always | Below 1 Ω |
| I20-4 (EFIO) or A25-31 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| I20-3 (EFII) - A25-29 (IMO) | Always | Below 1 Ω |
| I20-3 (EFII) or A25-29 (IMO) - Body ground | Always | 10 kΩ or higher |
| I20-4 (EFIO) - A25-28 (IMI) | Always | Below 1 Ω |
| I20-4 (EFIO) or A25-28 (IMI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 13.REGISTER ECU COMMUNICATION ID |
Register the ECU communication ID.
| NEXT | |
| 14.CHECK WHETHER ENGINE STARTS |
Check that the engine starts.
|
| ||||
| OK | ||
| ||
| 15.REPLACE ID CODE BOX (IMMOBILISER CODE ECU) |
Replace the ID code box (immobiliser code ECU) with a new one.
| NEXT | |
| 16.REGISTER ECU COMMUNICATION ID |
Register the ECU communication ID.
| NEXT | |
| 17.CHECK WHETHER ENGINE STARTS |
Check that the engine starts.
| Result | Proceed to |
| OK | A |
| NG (for 2GR-FE) | B |
| NG (for 2AR-FE) | C |
|
| ||||
|
| ||||
| A | ||
| ||