Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P003012    HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery

DTC    P003013    HO2S Heater Control Bank 1 Sensor 1 Circuit Open

DTC    P101A9E    A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On

for Preparation Click here


DESCRIPTION

Refer to DTC P21951D .

HINT:
  1. When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.
  2. Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  3. The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.


A338252E01


DTC No.
DTC Detection Condition
Trouble Area
P003012
Air fuel ratio sensor heater current reaches the high limit (1 trip detection logic).
  1. Short in air fuel ratio sensor (sensor 1) heater circuit
  2. Air fuel ratio sensor (sensor 1)
  3. ECM
P003013
Air fuel ratio sensor heater current is less than 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or higher (1 trip detection logic).
  1. Open or short in air fuel ratio sensor (sensor 1) heater circuit
  2. Air fuel ratio sensor (sensor 1)
  3. No. 1 integration relay
  4. ECM
P101A9E
Air fuel ratio sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
  1. Short in air fuel ratio sensor (sensor 1) heater circuit
  2. ECM

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.
The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.
When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY


Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


P003012 
Output duty cycle
Higher than 0%

P003013 
Output duty cycle
30% or higher

P101A9E 
Output duty cycle
Less than 60%

CONFIRMATION DRIVING PATTERN


A262623E04

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine / Trouble Codes [E].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  12. Input the DTC: P003012, P003013 or P101A9E.
  13. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.


WIRING DIAGRAM

Refer to DTC P21951D .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:
  1. Refer to "Data List / Active Test" [A/F (O2) Sensor Heater Duty Ratio B1S1] (Click here).
  2. Sensor 1 refers to the sensor closest to the engine assembly.
  3. Sensor 2 refers to the sensor farthest away from the engine assembly.
  4. Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor output voltage . If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
  5. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)


    A194092E47
  1. Disconnect the air fuel ratio sensor connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E19-2 (+B) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E19-1 (HA1A) - E96-19 (HA1A)
    Always
    Below 1 Ω
    E19-1 (HA1A) or E96-19 (HA1A) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003012, P003013 OR P101A9E)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    DTC P003012, P003013 or P101A9E is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - AIR FUEL RATIO SENSOR)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the No. 1 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1A-7 - E19-2 (+B)
    Always
    Below 1 Ω
    1A-7 or E19-2 (+B) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)


    A256530E07
  1. Disconnect the No. 1 integration relay connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Integration Relay)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1D-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)