DTC P042000 Catalyst System Efficiency Below Threshold Bank 1 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P042000 | The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic). |
|

| *1 | Air Fuel Ratio Sensor (Sensor 1) | *2 | Heated Oxygen Sensor (Sensor 2) |
| *3 | TWC: Front Catalyst | *4 | TWC: Rear Catalyst |
| *5 | Center Exhaust Pipe Assembly | *6 | Tail Exhaust Pipe Assembly |
| *7 | Exhaust Manifold Converter Sub-assembly | *8 | Front Exhaust Pipe Assembly |
| Required Sensors/Components (Main) | Air fuel ratio sensor Heated oxygen sensor |
| Required Sensors/Components (Related) | Intake air temperature sensor Mass air flow meter sub-assembly Crankshaft position sensor Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Idling | Off |
| Engine speed | Less than 4000 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10% or higher, and less than 90% |
| All of the following conditions are met | - |
| Mass air flow rate | 2.5 gm/sec or more, and less than 45 gm/sec |
| Front catalyst temperature (estimated) | 556°C (1032°F) or higher, and less than 840°C (1544°F) |
| Rear catalyst temperature (estimated) | 415°C (779°F) or higher, and less than 770°C (1418°F) |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|


| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042000) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P042000 is output | A |
| DTC P042000 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.
Perform the Active Test with the engine idling (press the Active Test button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.
| GTS Display (Sensor) | Injection Volume | Status | Voltage |
| A/F (O2) Sensor Voltage B1S1 (Air fuel ratio) | 12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2 Sensor Voltage B1S2 (Heated oxygen) | 12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status of A/F (O2) Sensor Voltage B1S1 | Status of O2 Sensor Voltage B1S2 | Actual air fuel ratio, air fuel ratio sensor and heated oxygen sensor condition | Misfire | Main Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | - |
| B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | - |
| |
| Lean/Rich | Lean | Heated oxygen sensor malfunction | - |
| C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction | - |
| |
| Lean | Lean | Actual air fuel ratio lean | May occur |
| D |
| Rich | Rich | Actual air fuel ratio rich | - |
|
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / All Data / Engine Speed and Intake Manifold Absolute Pressure.
Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stalls |
| Intake Manifold Absolute Pressure (Data List) | Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs) (150 to 300 mmHg(abs)) (EGR valve is fully closed) | Intake Manifold Absolute Pressure value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
|
| ||||
| 5.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 6.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST) |
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) (Click here).
Replace the front exhaust pipe assembly (TWC: Rear catalyst) (Click here).
| NEXT | ||
| ||
| 7.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
|
| ||||
| 8.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 9.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
|
| ||||
| 10.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 11.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / All Data / Engine Speed and Intake Manifold Absolute Pressure.
Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stalls |
| Intake Manifold Absolute Pressure (Data List) | Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs) (150 to 300 mmHg(abs)) (EGR valve is fully closed) | Intake Manifold Absolute Pressure value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
|
| ||||
| 12.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 13.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO |
Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P017100 Inspection Procedure (Click here).
|
| ||||
| 14.REPAIR OR REPLACE EXHAUST GAS LEAK POINT |
Repair or replace the exhaust gas leak point.
| NEXT | |
| 15.CHECK WHETHER DTC OUTPUT RECURS (DTC P042000) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P042000 is output | A |
| DTCs are not output (No pending DTCs output) | B |
|
| ||||
| A | |
| 16.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST) |
Replace the exhaust manifold converter sub-assembly (TWC: Front catalyst) (Click here).
Replace the front exhaust pipe assembly (TWC: Rear catalyst) (Click here).
| NEXT | ||
| ||