Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P017100    System Too Lean Bank 1

DTC    P017200    System Too Rich Bank 1

DTC    P117000    Fuel Performance/Port Injector

DTC    P117B00    Fuel Performance/Direct Injector

for Preparation Click here


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection duration. The fuel trim consists of both the short-term and long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No.
DTC Detection Condition
Trouble Area
P017100
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic).
  1. Intake system
  2. Fuel injector assembly (for port injection)
  3. Fuel injector assembly (for direct injection)
  4. Mass air flow meter sub-assembly
  5. Engine coolant temperature sensor
  6. Fuel pressure
  7. Fuel pressure sensor
  8. Gas leak from exhaust system
  9. Open or short in air fuel ratio sensor circuit
  10. Air fuel ratio sensor
  11. PCV valve and hose
  12. PCV hose connections
  13. EGR valve assembly
  14. Wire harness or connector
  15. ECM
P017200
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic).
  1. Intake system
  2. Fuel injector assembly (for port injection)
  3. Fuel injector assembly (for direct injection)
  4. Mass air flow meter sub-assembly
  5. Engine coolant temperature sensor
  6. Ignition system
  7. Fuel pressure
  8. Fuel pressure sensor
  9. Gas leak from exhaust system
  10. Open or short in air fuel ratio sensor circuit
  11. Air fuel ratio sensor
  12. EGR valve assembly
  13. Wire harness or connector
  14. ECM
P117000
Although a DTC is stored for a rich or lean condition, the amount of fuel trim during direct injection is normal (1 trip detection logic)
  1. Fuel injector assembly (for port injection)
  2. Fuel pressure
  3. ECM
P117B00
Although a DTC is stored for a rich or lean condition, the amount of fuel trim during port injection is normal (1 trip detection logic)
  1. Fuel injector assembly (for direct injection)
  2. Fuel pressure
  3. ECM

HINT:
  1. When DTC P017100 is stored, the actual air fuel ratio is on the lean side. When DTC P017200 is stored, the actual air fuel ratio is on the rich side.
  2. If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P017100 may be stored. The MIL is then illuminated.
  3. When DTC P117000 or P117B00 is output, it may not be possible to precisely determine whether the port injection or the direct injection is malfunctioning, depending on the conditions. In this case, perform an Active Test (Control the Injection Mode) to determine which injection system is malfunctioning.


MONITOR DESCRIPTION

Under closed loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the fuel injection volumes estimated by the ECM also affect the average fuel trim learned value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learned value of the air fuel ratio). If the average fuel trim learned value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and stores a DTC.
Example:
The average fuel trim learned value is +48% or higher, or -35% or less, the ECM interprets this as a fuel system malfunction.

A316543E01


MONITOR STRATEGY


Required Sensors/Components
Air fuel ratio sensor
Mass air flow meter sub-assembly
Crankshaft position sensor
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


Fuel system status
Closed loop
Battery voltage
11 V or higher
Either of the following conditions is met
1 or 2
1. Engine speed
Less than 1100 rpm
2. Engine load
10% or higher

TYPICAL MALFUNCTION THRESHOLDS


P017100 and P017200: Fuel Trim 
EVAP purge-cut
Executing
Either of the following conditions is met
1 or 2
1. Average between short-term fuel trim and long-term fuel trim
48% or higher (varies with engine coolant temperature)
2. Average between short-term fuel trim and long-term fuel trim
-35% or less (varies with engine coolant temperature)

P117000: Fuel Trim (Port Injection Fail) 
DTCs of fuel system have already been set
-
EVAP purge-cut
Executing
Direct injection
100%
Both of the following conditions are met
1 and 2
1. Average between short-term fuel trim and long-term fuel trim
Less than 48% (varies with engine coolant temperature)
2. Average between short-term fuel trim and long-term fuel trim
Higher than -35% (varies with engine coolant temperature)

P117B00: Fuel Trim (Direct Injection Fail) 
DTCs of fuel system have already been set
-
EVAP purge-cut
Executing
Port injection
100%
Both of the following conditions are met
1 and 2
1. Average between short-term fuel trim and long-term fuel trim
Less than 48% (varies with engine coolant temperature)
2. Average between short-term fuel trim and long-term fuel trim
Higher than -35% (varies with engine coolant temperature)

CONFIRMATION DRIVING PATTERN


A288929E02

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on [A].
  6. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].
  7. With the engine warmed up, idle the engine for 2 minutes or more [C].
  8. Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [E].
  10. Read the pending DTCs.

    HINT:
    If a pending DTC is output, the system is malfunctioning.


WIRING DIAGRAM

  1. Refer to DTC P010012 for the mass air flow meter sub-assembly circuit .
  2. Refer to DTC P21951D for the air fuel ratio sensor circuit .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  4. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
  5. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P017100, P017200, P117000 OR P117B00)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P017100, P017200, P117000 or P117B00 is output
    A
    DTC P017100, P017200, P117000 and/or P117B00 and other DTCs are output
    B

    HINT:
    If any DTCs other than P017100, P017200, P117000 or P117B00 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION MODE)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Port / Data List / All Data / Injection Mode, Short FT Bank 1 and Long FT Bank 1.

    HINT:
    1. When using the "Control the Injection Mode" Active Test to check the condition of the engine, switch from "Port" to "Direct".
    2. Do not switch from "Direct" to "Port". When performing the inspection more than once, after the Active Test ends, lightly race the engine, and then perform the inspection from "Port" again.
    3. If the display does not switch from "Port" even after lighting racing the engine, idle the engine for approximately 1 minute, and then lightly race the engine.

  1. Read the values displayed on the GTS.

    OK:
    Short FT Bank 1 + Long FT Bank 1 = Between -19% and +19% (Port Injection).

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / All Data / Injection Mode, Short FT Bank 1 and Long FT Bank 1.

    HINT:
    1. When using the "Control the Injection Mode" Active Test to check the condition of the engine, switch from "Port" to "Direct".
    2. Do not switch from "Direct" to "Port". When performing the inspection more than once, after the Active Test ends, lightly race the engine, and then perform the inspection from "Port" again.
    3. If the display does not switch from "Port" even after lighting racing the engine, idle the engine for approximately 1 minute, and then lightly race the engine.

  1. Read the values displayed on the GTS.

    OK:
    Short FT Bank 1 + Long FT Bank 1 = Between -19% and +19% (Direct Injection).


    Result:

    Item
    Proceed to
    Port
    Direct
    OK
    OK
    A
    OK
    NG
    B
    NG
    OK
    C
    NG
    NG
    D



B
Go to step 4

C
Go to step 10

D
Go to step 11
A


3.CHECK IF VEHICLE HAS RUN OUT OF FUEL IN PAST
  1. Has the vehicle run out of fuel in the past?



NO
CHECK FOR INTERMITTENT PROBLEMS (Click here)
YES

DTC CAUSED BY RUNNING OUT OF FUEL 

4.READ VALUE USING GTS (FUEL PRESSURE (HIGH))
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Fuel Pressure (High).

  1. Read the values.

    Standard:
    2750 to 8000 kPag (3000 rpm, engine warmed up, shift lever in P, A/C off).



NG
Go to step 7
OK


5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION MODE (DIRECT))
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / All Data / High Pressure Fuel Pump Duty Ratio (D4), Injection Mode, Short FT Bank 1 and Long FT Bank 1.

    HINT:
    1. When using the "Control the Injection Mode" Active Test to check the condition of the engine, switch from "Port" to "Direct".
    2. Do not switch from "Direct" to "Port". When performing the inspection more than once, after the Active Test ends, lightly race the engine, and then perform the inspection from "Port" again.
    3. If the display does not switch from "Port" even after lighting racing the engine, idle the engine for approximately 1 minute, and then lightly race the engine.

  1. Read the values displayed on the GTS.

    HINT:
    The A/C switch and all accessory switches should be off, and the shift lever should be in the P position, and the engine should be fully warmed up.


    Result:

    Item
    Proceed to
    High Pressure Fuel Pump Duty Ratio (D4)
    Short FT Bank 1 + Long FT Bank 1
    10% to 40%
    -
    A
    40% or higher
    -20% or less
    B
    10% or less
    +20% or higher
    40% or higher
    +20% or higher
    C
    10% or less
    -20% or less
    D



B
REPLACE FUEL DELIVERY PIPE (FUEL PRESSURE SENSOR) (Click here)

C
Go to step 8

D
REPLACE ECM (Click here)
A


6.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION MODE (DIRECT))
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / All Data / High Pressure Fuel Pump Duty Ratio (D4), Injection Mode, Short FT Bank 1 and Long FT Bank 1.

    HINT:
    1. When using the "Control the Injection Mode" Active Test to check the condition of the engine, switch from "Port" to "Direct".
    2. Do not switch from "Direct" to "Port". When performing the inspection more than once, after the Active Test ends, lightly race the engine, and then perform the inspection from "Port" again.
    3. If the display does not switch from "Port" even after lighting racing the engine, idle the engine for approximately 1 minute, and then lightly race the engine.

  1. Read the values displayed on the GTS.

    HINT:
    The A/C switch and all accessory switches should be off, and the shift lever should be in the P position, and the engine should be fully warmed up.


    Result:

    Item
    Proceed to
    High Pressure Fuel Pump Duty Ratio (D4)
    Short FT Bank 1 + Long FT Bank 1
    10% to 40%
    -25% or less
    A
    10% to 40%
    +25% or higher
    10% to 40%
    -25% to +25%
    B

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (for direct injection) (Click here).



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION) (Click here)  

7.CHECK MISFIRE COUNT OF DIRECT INJECTION
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Direct / Data List / All Data / Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #4.

    HINT:
    1. When using the "Control the Injection Mode" Active Test to check the condition of the engine, switch from "Port" to "Direct".
    2. Do not switch from "Direct" to "Port". When performing the inspection more than once, after the Active Test ends, lightly race the engine, and then perform the inspection from "Port" again.
    3. If the display does not switch from "Port" even after lighting racing the engine, idle the engine for approximately 1 minute, and then lightly race the engine.

  1. Read the values displayed on the GTS.

    Result:

    Injection Mode
    Misfire Count
    Proceed to
    Direct
    No misfire counts, or misfire counts occur randomly in all cylinders
    A
    Misfire counts occur in particular cylinder
    B

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (for direct injection) (Click here).



B
REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION) (Click here)
A


8.REPLACE FUEL PUMP (FOR HIGH PRESSURE SIDE)
  1. Replace the fuel pump (for high pressure side) (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel pump (for high pressure side) (Click here).


NEXT


9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED (DTC P017100, P017200, P117000 OR P117B00)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P017100, P017200, P117000 and/or P117B00 is output
    A
    DTCs are not output
    B



B
END
A

REPLACE ECM (Click here)  

10.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
  1. Check the injection volume (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (for port injection) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)
OK

REPLACE ECM (Click here)  

11.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections (Click here).

    OK:
    PCV valve and hose are connected correctly and are not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


12.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


13.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

  1. Perform the Control the Injection Volume for A/F Sensor for operation with the engine idling (press the Active Test button to change the fuel injection volume).

  1. Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    3. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard:

    GTS Display (Sensor)
    Injection Volume
    Status
    Voltage
    A/F (O2) Sensor Voltage B1S1
    (Air fuel ratio)
    12.5%
    Rich
    Below 3.1 V
    -12.5%
    Lean
    Higher than 3.4 V
    O2 Sensor Voltage B1S2
    (Heated oxygen)
    12.5%
    Rich
    Higher than 0.55 V
    -12.5%
    Lean
    Below 0.4 V


    Result:

    Status of A/F (O2) Sensor Voltage B1S1
    Status of O2 Sensor Voltage B1S2
    Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    A
    Lean
    Lean
    Actual air fuel ratio lean
    1. PCV valve and hose
    2. PCV hose connections
    3. Gas leak from exhaust system
    4. Intake system
    5. Fuel pressure
    6. Mass air flow meter sub-assembly
    7. Engine coolant temperature sensor
    8. EGR valve assembly
    Rich
    Rich
    Actual air fuel ratio rich
    1. Gas leak from exhaust system
    2. Ignition system
    3. Fuel pressure
    4. Mass air flow meter sub-assembly
    5. Engine coolant temperature sensor
    6. EGR valve assembly
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    1. Air fuel ratio sensor
    2. EGR valve assembly
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    1. Air fuel ratio sensor

    1. Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (A/F (O2) Sensor Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2 Sensor Voltage B1S2) is consistently below 0.4 V.
    2. Rich: During Control the Injection Volume for A/F Sensor, the A/F (O2) Sensor Voltage B1S1 is consistently below 3.1 V, and the O2 Sensor Voltage B1S2 is consistently higher than 0.55 V.
    3. Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternates correctly.

    HINT:
    Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2] (Click here).



B
Go to step 20
A


14.READ VALUE USING GTS (COOLANT TEMPERATURE)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temperature.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:

    GTS Display
    Condition
    Specified Condition
    Coolant Temperature
    Cold engine
    Same as ambient air temperature
    Warm engine
    Between 75 and 100°C (167 and 212°F)

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


15.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed, Mass Air Flow Sensor and Coolant Temperature.

  1. Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.

  1. Read Mass Air Flow Sensor with the engine speed at 3000 rpm.

    Standard:

    GTS Display
    Condition
    Specified Condition
    Mass Air Flow Sensor
    Shift lever position: P
    A/C: Off
    Engine Speed: 3000 rpm
    Between 6.2 gm/sec and 11.2 gm/sec



NG
Go to step 26
OK


16.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


17.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)
  1. Check the fuel pressure (for low pressure side) .



OK
Go to step 24

NG
Go to step 18

18.CHECK FUEL PUMP OPERATION (FOR LOW PRESSURE SIDE)
  1. Check the fuel pump operation (for low pressure side) .



NG
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
OK


19.CHECK FUEL LEAK (FOR LOW PRESSURE SIDE)
  1. Check for fuel leaks (for low pressure side).

    OK:
    No leaks.



NG
REPAIR OR REPLACE FUEL SYSTEM (FOR LOW PRESSURE SIDE)
OK

CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL LINE AND FILTER 

20.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


21.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E19-1 (HA1A) - E96-19 (HA1A)
    Always
    Below 1 Ω
    E19-3 (A1A+) - E96-131 (A1A+)
    Always
    Below 1 Ω
    E19-4 (A1A-) - E96-132 (A1A-)
    Always
    Below 1 Ω
    E19-1 (HA1A) or E96-19 (HA1A) - Body ground and other terminals
    Always
    10 kΩ or higher
    E19-3 (A1A+) or E96-131 (A1A+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E19-4 (A1A-) or E96-132 (A1A-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


22.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).


NEXT


23.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED (DTC P017100, P017200, P117000 OR P117B00)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P017100, P017200, P117000 and/or P117B00 is output
    A
    DTCs are not output
    B



B
END
A


24.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / All Data / Engine Speed and Intake Manifold Absolute Pressure.

  1. Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.

    NOTICE:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    Steady idling
    Idling changes from steady to rough idling or engine stalls
    Intake Manifold Absolute Pressure
    (Data List)
    Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs)
    (150 to 300 mmHg(abs))
    (EGR valve is fully closed)
    Intake Manifold Absolute Pressure value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



OK
Go to step 26

NG
Go to step 25

25.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


26.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


27.CHECK WHETHER DTC OUTPUT RECURS (DTC P017100, P017200, P117000 OR P117B00)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P017100, P017200, P117000 and/or P117B00 is output
    A
    DTCs are not output
    B



B
END
A


28.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
  1. Disconnect the mass air flow meter sub-assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E105-3 (5V) - E96-90 (VCVG)
    Always
    Below 1 Ω
    E105-1 (FG) - E96-92 (VG)
    Always
    Below 1 Ω
    E105-2 (E2G) - E96-91 (E2G)
    Always
    Below 1 Ω
    E105-3 (5V) or E96-90 (VCVG) - Body ground and other terminals
    Always
    10 kΩ or higher
    E105-1 (FG) or E96-92 (VG) - Body ground and other terminals
    Always
    10 kΩ or higher
    E105-2 (E2G) or E96-91 (E2G) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


29.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
  1. Replace the mass air flow meter sub-assembly (Click here).

    HINT:
    1. If the result of the inspection performed in step 15 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here).


NEXT


30.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P017100, P017200, P117000 and/or P117B00 is output
    A
    DTCs are not output
    B



B
END
A

REPLACE ECM (Click here)