Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › IGNITION SYSTEM

IGNITION SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. PERFORM SPARK PLUG TEST
  1. Check for DTCs (Click here).

    NOTICE:
    If any DTCs are present, perform troubleshooting in accordance with the procedure for each DTC.

  1. Remove the 4 ignition coil assemblies and 4 spark plugs (Click here).

    NOTICE:
    If an ignition coil assembly or spark plug has been struck or dropped, replace it.

    HINT:
    Arrange the removed parts in the correct order.



    A338460
  1. Disconnect the fuel injector connector (for Port Injection).



    A338461
  1. Disconnect the fuel injector connector (for Direct Injection).

  1. Install the spark plug to the ignition coil assembly, and then connect the ignition coil assembly connector.

  1. Ground the spark plug.



    A337983
  1. Check that spark occurs at each spark plug while the engine is being cranked.

    NOTICE:
    1. Be sure to ground the spark plugs when checking them.
    2. Do not crank the engine for more than 2 seconds.
    3. If an ignition coil assembly or spark plug has been struck or dropped, replace it.

    HINT:
    If spark does not occur, perform the following procedure.

  1. Connect the fuel injector connector (for Direct Injection).

  1. Connect the fuel injector connector (for Port Injection).

  1. Install the 4 spark plugs and 4 ignition coil assemblies (Click here).

    NOTICE:
    If an ignition coil assembly or spark plug has been struck or dropped, replace it.

    HINT:
    Install the same parts to their original positions.

  1. Check for DTCs (Click here).

  1. Clear the DTCs (Click here).



2. INSPECT IGNITION COIL ASSEMBLY AND SPARK TEST

HINT:
Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly (Click here).

  1. Check that the ignition coil assembly connector is securely connected.

    Result:
    Result
    Action
    NG
    Connect securely
    OK
    Go to next step

  1. Perform a spark test on each ignition coil assembly.

    1. Replace the ignition coil assembly with a known good one.

    2. Perform the spark test again.

      Result:
      Result
      Action
      NG
      Go to next step
      OK
      Replace ignition coil assembly

  1. Perform a spark test on each spark plug.

    1. Replace the spark plug with a known good one.

    2. Perform the spark test again.

      Result:
      Result
      Action
      NG
      Inspect the ignition system
      (Click here)
      OK
      Replace spark plug

      NOTICE:
      If an ignition coil assembly or spark plug has been struck or dropped, replace it.

  1. Connect the fuel injector connector (for Direct Injection).

  1. Connect the fuel injector connector (for Port Injection).

  1. Install the 4 spark plugs and 4 ignition coil assemblies (Click here).

    NOTICE:
    If an ignition coil assembly or spark plug has been struck or dropped, replace it.

    HINT:
    Install the same parts to their original positions.

  1. Check for DTCs (Click here).

  1. Clear the DTCs (Click here).



3. INSPECT SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Never attempt to adjust the electrode gap of a used spark plug.

HINT:
Perform "Inspection After Repair" after replacing a spark plug (Click here).



  1. Check the electrode.



      I039522E57
    1. Using a megohmmeter, measure the insulation resistance.
      Text in Illustration 
      *a
      Body Ground

      Standard Insulation Resistance:
      Tester Connection
      Condition
      Specified Condition
      Spark plug (terminal part) - Body ground
      Always
      10 MΩ or higher

      HINT:
      1. If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
      2. If a megohmmeter is not available, perform the following simple inspection instead.

  1. Alternative inspection method.

    1. Start the engine.

      NOTICE:
      Do not perform this step when any of the following DTCs are output; P030000, P030027, P030085, P030100, P030200, P030300, P030400 (Cylinder Misfire Detected)

    2. Quickly accelerate the engine to 4000 rpm 5 times.

      NOTICE:
      Do not perform this step when any of the following DTCs are output; P030000, P030027, P030085, P030100, P030200, P030300, P030400 (Cylinder Misfire Detected)

    3. Remove the spark plug (Click here).

    4. Visually check the spark plug.

      HINT:
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage to its threads and insulator. If there is any damage, replace the spark plug.

    Recommended Spark Plug:
    Manufacturer
    Spark Plug Type
    DENSO
    FK16HBR-J8



    A155866E07
  1. Check the spark plug electrode gap.
    Text in Illustration 
    *a
    Spark Plug Electrode Gap
    *b
    Iridium Tip
    *c
    Platinum Tip

    Maximum Electrode Gap for Used Spark Plug:
    1.1 mm (0.0433 in.)

    NOTICE:
    Never attempt to adjust the electrode gap of a used spark plug.

    If the electrode gap is more than the maximum, replace the spark plug.

    Standard Electrode Gap for New Spark Plug:
    0.7 to 0.8 mm (0.0276 to 0.0315 in.)



    A296690
  1. Clean the spark plug.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Standard Air Pressure:
    588 kPa (6.0 kgf/cm2, 85 psi)

    Standard Duration:
    20 seconds or less

    HINT:
    Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

  1. Install the spark plug (Click here).



4. PERFORM INITIALIZATION
  1. Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly (Click here).