Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2017.09–2017.12
RM33A0E _58 Vehicle Interior _065380 LIGHTING (INT) _0327154 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

Ignition Key Cylinder Light (Transponder Key Coil)*

·

Map Light (Roof Console Box Sub-assembly)

·

Spot Light Assembly


*: w/o Smart Entry and Start System


WIRING DIAGRAM

E380182E01
1.156,0.135 2.115,0.344 0.958,0.208 10 false from Battery 1.167,1.104 1.563,1.313 0.396,0.208 10 false ALT 2.156,0.938 2.552,1.146 0.396,0.208 10 false 3G 2.615,0.938 3.01,1.146 0.396,0.208 10 false 3F 2.625,0.729 3.021,0.938 0.396,0.208 10 false 1 2.188,0.729 2.583,0.938 0.396,0.208 10 false 1 2.156,1.135 2.552,1.344 0.396,0.208 10 false *3 2.604,1.135 3,1.344 0.396,0.208 10 false *2 3.104,1.104 3.656,1.344 0.552,0.24 10 false DOME 4.104,1.594 4.969,1.813 0.865,0.219 10 false DOME CUT 5.521,0.938 5.917,1.146 0.396,0.208 10 false MB 5.521,2.292 5.917,2.5 0.396,0.208 10 false MB 5.552,0.729 5.948,0.938 0.396,0.208 10 false 23 5.573,2.083 5.969,2.292 0.396,0.208 10 false 1 5.927,0.823 6.5,1.052 0.573,0.229 10 false DOMR 5.938,2.177 6.51,2.406 0.573,0.229 10 false ILE 2.583,1.5 2.979,1.708 0.396,0.208 10 false 3B 2.594,1.896 2.99,2.104 0.396,0.208 10 false 3B 2.594,2.292 2.99,2.5 0.396,0.208 10 false 3B 2.615,1.302 3.01,1.51 0.396,0.208 10 false 24 2.604,1.708 3,1.917 0.396,0.208 10 false 10 2.615,2.115 3.01,2.323 0.396,0.208 10 false 29 2.906,2.719 5.75,2.99 2.844,0.271 10 false Instrument Panel Junction Block Assembly 1.646,1.385 2.042,1.594 0.396,0.208 10 false *1 1.333,5.521 4.792,5.813 3.458,0.292 10 false Ignition Key Cylinder Light (Transponder Key Coil)*1 4.948,4.552 5.344,4.76 0.396,0.208 10 false *1 1.333,5.365 1.729,5.573 0.396,0.208 10 false K61 1.396,4.552 1.792,4.76 0.396,0.208 10 false ILL+ 4.24,4.563 4.635,4.771 0.396,0.208 10 false ILL- 1.177,4.563 1.396,4.771 0.219,0.208 10 false 2 5.469,5.833 7.125,6.208 1.656,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 4.625,4.552 4.844,4.76 0.219,0.208 10 false 4 0.531,6.531 0.927,6.74 0.396,0.208 10 false A 5.292,6.542 5.688,6.75 0.396,0.208 10 false B 1.5,6.01 4.281,6.219 2.781,0.208 10 false *1: w/o Smart Entry and Start System 1.5,6.313 4.281,6.521 2.781,0.208 10 false *2: for LHD 1.5,6.604 4.281,6.813 2.781,0.208 10 false *3: for RHD

E377091E01
4.573,5.552 6.792,5.792 2.219,0.24 10 false *1: for Normal Roof 4.583,5.906 6.802,6.146 2.219,0.24 10 false *2: for Panoramic Moon Roof 3.469,3.188 3.823,3.406 0.354,0.219 10 false V13 4.99,2.385 5.344,2.604 0.354,0.219 10 false V13 4.979,0.948 5.333,1.167 0.354,0.219 10 false V13 1.167,1.24 1.521,1.458 0.354,0.219 10 false V13 3.469,3.385 3.823,3.604 0.354,0.219 10 false V14 5.417,2.385 5.771,2.604 0.354,0.219 10 false V14 5.417,0.948 5.771,1.167 0.354,0.219 10 false V14 0.74,1.24 1.094,1.458 0.354,0.219 10 false V14 4.25,3.24 6.042,3.635 1.792,0.396 10 false Map Light (Roof Console Box Sub-assembly) 5.073,1.188 5.333,1.448 0.26,0.26 10 false *1 5.052,2.615 5.313,2.875 0.26,0.26 10 false *1 3.885,3.198 4.146,3.458 0.26,0.26 10 false *1 1.24,1.469 1.5,1.729 0.26,0.26 10 false *1 5.479,2.615 5.74,2.875 0.26,0.26 10 false *2 5.479,1.188 5.74,1.448 0.26,0.26 10 false *2 0.792,1.469 1.052,1.729 0.26,0.26 10 false *2 1.25,1.031 1.51,1.292 0.26,0.26 10 false 1 5.063,0.74 5.323,1 0.26,0.26 10 false 3 5.073,2.188 5.333,2.448 0.26,0.26 10 false 4 3.25,3.198 3.51,3.458 0.26,0.26 10 false 2 3.26,3.406 3.521,3.667 0.26,0.26 10 false 2 5.51,0.74 5.771,1 0.26,0.26 10 false 1 5.479,2.177 5.74,2.438 0.26,0.26 10 false 15 0.792,1.031 1.052,1.292 0.26,0.26 10 false 14 3.885,3.396 4.146,3.656 0.26,0.26 10 false *2 1.875,2.813 2.844,3.031 0.969,0.219 10 false Map Light RH 1.573,1.115 2.073,1.375 0.5,0.26 10 false +B1 4.438,0.844 5.01,1.094 0.573,0.25 10 false DOOR 4.552,2.271 5.125,2.521 0.573,0.25 10 false GND 3.656,2.958 4.229,3.208 0.573,0.25 10 false RLMP 0.948,4.167 1.135,4.417 0.188,0.25 10 false B 2.833,4.083 3.208,4.354 0.375,0.271 10 false CTY 2.99,4.938 3.229,5.229 0.24,0.292 10 false E 0.729,4.167 0.917,4.417 0.188,0.25 10 false 5 3.219,4.094 3.406,4.344 0.188,0.25 10 false 2 3.229,4.917 3.417,5.167 0.188,0.25 10 false 1 1.229,5.844 3.031,6.073 1.802,0.229 10 false Spot Light Assembly 1.24,5.656 1.667,5.885 0.427,0.229 10 false V11 1.875,1.458 2.844,1.677 0.969,0.219 10 false Map Light LH 3.083,0.823 3.469,1.063 0.385,0.24 10 false OFF 3.073,2.688 3.458,2.927 0.385,0.24 10 false OFF 3.083,2.271 3.469,2.51 0.385,0.24 10 false ON 3.083,1.438 3.469,1.677 0.385,0.24 10 false ON 3.667,1.135 4.958,1.396 1.292,0.26 10 false Door Linked Switch 3.677,1.698 4.417,2.104 0.74,0.406 10 false Dome Light Switch 1.156,5.167 2.125,5.385 0.969,0.219 10 false Spot Light RH 1.198,4.5 2.167,4.719 0.969,0.219 10 false Spot Light LH 2.417,4.094 2.802,4.333 0.385,0.24 10 false OFF 2.417,4.75 2.802,4.99 0.385,0.24 10 false OFF 2.417,5.167 2.802,5.406 0.385,0.24 10 false ON 2.417,4.5 2.802,4.74 0.385,0.24 10 false ON 0.385,0.229 0.646,0.49 0.26,0.26 10 false A 5.99,0.229 6.25,0.49 0.26,0.26 10 false B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*2

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*1: w/ Smart Entry and Start System

*2: w/ Door Control Battery




HINT:

The DOME CUT relay supplies power to the interior lights. If all the lights that use power from the DOME CUT relay do not turn on, check the interior light auto cut circuit first.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>Interior Light Auto Cut Circuit


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Illuminated Entry System Turns on the lights that are controlled by the illuminated entry system* OFF or ON Perform the Active Test with the door linked switch of the map light (roof console box sub-assembly) on and switches of the spot light assembly LH and RH off.

*: Refer to System Description for the lights that are controlled by the illuminated entry system.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>SYSTEM DESCRIPTION


Body Electrical > Main Body > Active Test
Tester Display
Illuminated Entry System
50004 123 4
OK:

All lights that are controlled by the illuminated entry system come on.



Result:
Result Proceed to
OK A
NG (Map light (roof console box sub-assembly) and/or spot light assembly do not come on) B
NG (Ignition key cylinder light (transponder key coil) does not come on) C
NG (All lights that are controlled by the illuminated entry system do not come on) D



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT MAP LIGHT (ROOF CONSOLE BOX SUB-ASSEMBLY)

C

6.INSPECT IGNITION KEY CYLINDER LIGHT (TRANSPONDER KEY COIL)

D

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
2.INSPECT MAP LIGHT (ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Remove the map light (roof console box sub-assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light (roof console box sub-assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPOT LIGHT ASSEMBLY

NG

REPLACE MAP LIGHT (ROOF CONSOLE BOX SUB-ASSEMBLY)

3.INSPECT SPOT LIGHT ASSEMBLY
a.

Remove the spot light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>REMOVAL


b.

Inspect the spot light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT (ROOF CONSOLE BOX SUB-ASSEMBLY) - SPOT LIGHT ASSEMBLY)

NG

REPLACE SPOT LIGHT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT (ROOF CONSOLE BOX SUB-ASSEMBLY) - SPOT LIGHT ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Normal Roof
Tester Connection Condition Specified Condition
V13-1 (+B1) - V11-5 (B) Always Below 1 Ω
V13-2 (RLMP) - V11-2 (CTY) Always Below 1 Ω
V13-1 (+B1) or V11-5 (B) - Body ground Always 10 kΩ or higher
V13-2 (RLMP) or V11-2 (CTY) - Body ground Always 10 kΩ or higher

for Panoramic Moon Roof
Tester Connection Condition Specified Condition
V14-14 (+B1) - V11-5 (B) Always Below 1 Ω
V14-2 (RLMP) - V11-2 (CTY) Always Below 1 Ω
V14-14 (+B1) or V11-5 (B) - Body ground Always 10 kΩ or higher
V14-2 (RLMP) or V11-2 (CTY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MAP LIGHT (ROOF CONSOLE BOX SUB-ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MAP LIGHT (ROOF CONSOLE BOX SUB-ASSEMBLY))
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Connect the V13*1 or V14*2 map light (roof console box sub-assembly) connector.

*1: for Normal Roof

*2: for Panoramic Moon Roof



c.

Apply battery voltage to the connector and check that the map light comes on.

OK:
Measurement Condition Condition Specified Condition
Battery positive (+) → 3B-10
Battery negative (-) → 3B-29
Door linked switch on and map light switch LH and RH off Map light LH and RH come on



Result:
Proceed to
OK
NG



OK

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT IGNITION KEY CYLINDER LIGHT (TRANSPONDER KEY COIL)
a.

Remove the ignition key cylinder light (transponder key coil).

Click hereVehicle Interior>LIGHTING (INT)>IGNITION KEY CYLINDER LIGHT>REMOVAL


b.

Inspect the ignition key cylinder light (transponder key coil).

Click hereVehicle Interior>LIGHTING (INT)>IGNITION KEY CYLINDER LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE IGNITION KEY CYLINDER LIGHT (TRANSPONDER KEY COIL)

7.CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3F instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E341598C07
2.146,0.927 2.479,1.146 0.333,0.219 5.083,0.938 5.417,1.156 0.333,0.219 2.229,0.948 2.542,1.146 0.313,0.198 10 false 3B 0.271,0.198 0.583,0.396 0.313,0.198 10 false *a 5.167,0.958 5.479,1.156 0.313,0.198 10 false 3F
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-24 - 3F-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGNITION KEY CYLINDER LIGHT (TRANSPONDER KEY COIL) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (IGNITION KEY CYLINDER LIGHT (TRANSPONDER KEY COIL) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K61-2 (ILL+) - 3B-24 Always Below 1 Ω
K61-4 (ILL-) - 3B-29
K61-2 (ILL+) or 3B-24 - Body ground Always 10 kΩ or higher
K61-4 (ILL-) or 3B-29 - Body ground



Result:
Proceed to
OK
NG



OK

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E333581C26
1.333,0.365 1.625,0.583 0.292,0.219 4.76,0.5 5.052,0.719 0.292,0.219 3.302,1.125 3.531,1.479 false 0.167,0.177 0.479,0.333 0.313,0.156 10 false *a 1.396,0.385 1.854,0.615 0.458,0.229 10 false 3B 4.802,0.521 5.26,0.75 0.458,0.229 10 false MB 3.604,1.448 4.063,1.677 0.458,0.229 10 false ILE
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-29 - MB-1 (ILE) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY