Home › Engine / Hybrid System › 2AR-FE (LUBRICATION) › OIL PUMP › 2017.09–2018.04
RM33A0E _51 Engine / Hybrid System _065329 2AR-FE LUBRICATION _0328503 OIL PUMP A

2AR-FE LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during timing chain cover sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

*3: The vehicle height changes because of suspension or tire replacement.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


(Click here)for U760E Initialization
(Click here)for U760E Registration
Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Engine start


See Service Bulletin for the registration method.
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly. (Click here)
Suspension, tires*3 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

NOTICE:

Do not remove the oil pump or oil pump relief valve from the timing chain cover sub-assembly.


PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 82121 2.REMOVE ENGINE WIRE

Hide 11201 4.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11301K 5.REMOVE CRANKSHAFT POSITION SENSOR

Hide 12315A 7.REMOVE ENGINE MOUNTING BRACKET RH

a.
A407983

Remove the 4 bolts and engine mounting bracket RH.


Hide 16620 8.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11310 9.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A345983C02
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 17 bolts and 2 nuts.


b.

Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly with a screwdriver as shown in the illustration.

A283977C10
6.563,1.802 6.344,1.802 6.344,1.802 5.99,0.896 true 4.781,1.865 5.26,2.521 5.26,2.521 5.469,2.521 true 1.354,1.729 2.146,1.729 true 0.573,1.531 0.802,1.531 0.802,1.531 1.063,0.813 true 0.385,1.417 0.698,1.573 0.313,0.156 10 false *a 1.177,1.635 1.49,1.792 0.313,0.156 10 false *a 5.531,2.417 5.844,2.573 0.313,0.156 10 false *a 6.625,1.698 6.938,1.854 0.313,0.156 10 false *a
*a Protective Tape - -


NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly, stiffening crankcase assembly or timing chain cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
A196858C07
0.271,1.198 0.583,1.396 0.313,0.198 10 false *1 1.229,1.417 1.406,1.625 0.177,0.208 10 true *1 2.552,0.635 2.729,0.844 0.177,0.208 10 true *2
*1 Oil Pump Gasket
*2 Oil Hole Cover Gasket


Remove the 2 oil pump gaskets and oil hole cover gasket from the stiffening crankcase assembly.


Hide 11301C 10.REMOVE TIMING CHAIN COVER OIL SEAL

a.
A210537C17
2.135,1.115 2.344,1.406 2.344,1.406 2.625,1.406 true 0.719,0.396 1.052,0.396 1.052,0.396 1.396,0.771 true 2.688,1.333 2.927,1.552 0.24,0.219 10 false *b 0.542,0.313 0.781,0.531 0.24,0.219 10 false *a
*a Protective Tape
*b Wooden Block


Using a screwdriver and wooden block, pry out the timing chain cover oil seal.

NOTICE:

Do not damage the surface of the timing chain cover oil seal press fit hole or the crankshaft.


HINT:

Tape the screwdriver tip before use.