Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › ENGINE UNIT › 2017.09–2018.04
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321408 ENGINE UNIT A

2AR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE ENGINE COVER JOINT

a.
A196900

Remove the 3 engine cover joints.


Hide 19100P 2.REMOVE SPARK PLUG

Hide 11101J 3.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11101J 4.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 11102A 5.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11102A 6.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 12108 7.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.


Hide 12108A 8.REMOVE OIL FILLER CAP GASKET

a.

Remove the oil filler cap gasket from the oil filler cap sub-assembly.


Hide 11301K 9.REMOVE CRANKSHAFT POSITION SENSOR

Hide 12204 10.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 12205 11.REMOVE VENTILATION CASE SUB-ASSEMBLY

a.
A210185C05
1.26,1.938 1.573,2.135 0.313,0.198 10 true *a 3.01,1.656 3.323,1.854 0.313,0.198 10 true *a
*a Nut


Remove the 8 bolts and 2 nuts.


b.
A210186

Using a screwdriver with its tip wrapped with protective tape, remove the ventilation case sub-assembly by prying between the ventilation case sub-assembly and cylinder block sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and ventilation case sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 12215 12.REMOVE SEPARATOR CASE

a.
A210188

Remove the 2 bolts, separator case and gasket from the ventilation case sub-assembly.


Hide 16268 13.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A194876

Remove the bolt, 2 nuts, No. 1 water by-pass pipe and gasket.


Hide 16321 14.REMOVE WATER INLET

Hide 16331A 15.REMOVE THERMOSTAT

Hide 15710 16.REMOVE OIL COOLER ASSEMBLY (w/ Oil Cooler)

Hide 16620 17.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A407997

Remove the bolt and V-ribbed belt tensioner assembly.


Hide 18.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A412655

Remove the bolt and wire harness clamp bracket.


Hide 16100 19.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 16323 20.REMOVE WATER INLET HOUSING

a.
A195872C04
1.5,1.979 1.813,2.177 0.313,0.198 10 true *a 1.875,1.125 2.188,1.323 0.313,0.198 10 true *a 1.844,0.135 2.156,0.333 0.313,0.198 10 true *a 2.313,0.094 2.625,0.292 0.313,0.198 10 true *a 3.021,0.74 3.333,0.938 0.313,0.198 10 true *b
*a Bolt
*b Nut


Remove the 4 bolts, nut and water inlet housing from the cylinder block sub-assembly.


b.
A343280

Remove the gasket from the cylinder block sub-assembly.


c.
A343281

w/o Oil Cooler:

i.

Using an E6 "TORX" socket wrench, remove the 4 stud bolts from the water inlet housing.

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.




d.

w/ Oil Cooler:

i.

Using an E6 "TORX" socket wrench, remove the 5 stud bolts from the water inlet housing.

A412645

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.




Hide 11201 22.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A195876C07
2.615,1.156 2,1.396 2,1.396 1.323,1.042 true 2.01,1.385 2.135,1.156 false 1.927,1.417 2.24,1.615 0.313,0.198 10 false *a
*a Seal Washer


Remove the 16 bolts, 3 seal washers, cylinder head cover sub-assembly and cylinder head cover gasket.


b.
A196857C01
0.51,0.615 0.708,0.792 0.198,0.177 10 true *1 2.677,0.531 2.875,0.708 0.198,0.177 10 true *1 2.198,0.031 2.396,0.208 0.198,0.177 10 true *a
*1 Camshaft Bearing Cap Oil Hole Gasket
*a Gasket


Remove the 2 camshaft bearing cap oil hole gaskets from the No. 1 camshaft bearing cap.


c.

Remove the gasket from the No. 2 camshaft bearing cap.


Hide 11193 23.REMOVE SPARK PLUG TUBE GASKET

a.
A195877

Using a screwdriver, pry out the 4 spark plug tube gaskets.

NOTICE:

Be careful not to damage the cylinder head cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 12315A 24.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11310 25.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 26.REMOVE OIL PUMP RELIEF VALVE PLUG

a.
A196859

Using a 14 mm hexagon wrench, remove the oil pump relief valve plug and gasket.


Hide 11324 27.REMOVE TIMING CHAIN COVER PLATE

Hide 11301C 28.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 29.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.

A292247C18
5.969,2.917 6.219,2.771 false 3.51,5.708 4.646,5.438 false 1.021,2.833 1.031,3.021 false 0.958,0.354 1.271,0.51 0.313,0.156 10 false *a 6.25,0.448 6.563,0.604 0.313,0.156 10 false *b 5.792,2.875 6.104,3.031 0.313,0.156 10 false *c 4.708,5.323 5.021,5.479 0.313,0.156 10 false *1 0.969,3.042 1.281,3.198 0.313,0.156 10 false *c 6.688,3.656 6.844,3.854 0.156,0.198 10 false A 1.646,2.719 1.802,2.917 0.156,0.198 10 false A
*1 Crankshaft Pulley Key - -
*a Approximately 7° *b Approximately 32°
*c Timing Mark - -



b.

Rotate the crankshaft clockwise and align the crankshaft pulley key as shown in the illustration.


c.

Check that the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.

HINT:

"A" is not a timing mark.



d.

Remove the crankshaft pulley bolt.


Hide 13540 31.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 32.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 34.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13521 35.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A196881

Remove the crankshaft timing sprocket from the crankshaft.


Hide 13050 36.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 37.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11103 38.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 15678A 40.REMOVE OIL CONTROL VALVE FILTER

a.
A196915

Remove the oil control valve filter from the No. 1 camshaft bearing cap.


Hide 11811 43.REMOVE NO. 1 CAMSHAFT BEARING

a.
A285349

Remove the No. 1 camshaft bearing from the No. 1 camshaft bearing cap.


Hide 11821 44.REMOVE NO. 2 CAMSHAFT BEARING

a.
A285350

Remove the No. 2 camshaft bearing from the camshaft housing sub-assembly.


Hide 11151A 45.REMOVE CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the camshaft bearing cap setting ring pins unless they are being replaced.


a.
A241923

Remove the 10 camshaft bearing cap setting ring pins from the camshaft housing sub-assembly.


Hide 11114A 46.REMOVE CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove the camshaft housing straight pins unless they are being replaced.


a.
A241924

Remove the 2 camshaft housing straight pins from the camshaft housing sub-assembly.


Hide 13801 47.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 48.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 50.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11445 52.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A196938

Remove the cylinder block water jacket spacer from the cylinder block sub-assembly.

NOTICE:

Be sure to remove the cylinder block water jacket spacer. If it is not removed, it may fall and become damaged when the cylinder block sub-assembly is inverted.



Hide 15620 53.REMOVE OIL FILTER CAP ASSEMBLY

Hide 12101A 54.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket from the oil pan sub-assembly.


Hide 12101 55.REMOVE OIL PAN SUB-ASSEMBLY

a.
A210204C18
0.771,1.219 1.781,1.396 1.781,1.396 1.5,1.813 true 1.823,1.323 2.063,1.469 0.24,0.146 10 false *a
*a Nut


Remove the 11 bolts and 2 nuts.


b.
A118769

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and stiffening crankcase assembly, cut through the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the stiffening crankcase assembly and oil pan sub-assembly.

·

Be careful not to damage the oil pan sub-assembly flange.




Hide 15104 56.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A196919

Remove the 3 bolts and oil strainer sub-assembly.


b.

Remove the oil strainer gasket from the oil strainer sub-assembly.


Hide 12121 57.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A196920

Remove the 5 bolts and No. 1 oil pan baffle plate.


Hide 58.INSPECT CRANKSHAFT BACKLASH

a.
A196931

Using a dial indicator, measure the backlash of the crankshaft and balance shaft as shown in the illustration.

Standard backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


Maximum backlash:

0.20 mm (0.00787 in.)


If the backlash is more than the maximum, replace the engine balancer assembly.


Hide 13620B 59.REMOVE ENGINE BALANCER ASSEMBLY

a.
A196921

Remove the 7 bolts and engine balancer assembly from the stiffening crankcase assembly.

NOTICE:

Do not disassemble the engine balancer assembly.



Hide 11420 60.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A196933

Remove the 7 bolts.


b.
A196934C03
0.036,0.0 0.208,0.157 0.172,0.157 10 *a 0.036,2.131 0.2,2.308 0.164,0.177 10 *b
*a LH Side
*b RH Side


Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block sub-assembly at the places shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and stiffening crankcase assembly.


HINT:

Tape the screwdriver tip before use.



Hide 61.REMOVE STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove the stiffening crankcase ring pins unless they are being replaced.


a.
A241936

Remove the 2 stiffening crankcase ring pins from the stiffening crankcase assembly.


Hide 62.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A260357

Using an E6 "TORX" socket wrench, remove the 3 stud bolts from the cylinder head cover sub-assembly.


b.
A241922

Using an E8 "TORX" socket wrench, remove the stud bolt from the camshaft housing sub-assembly.


c.
A241935

Using E5 and E8 "TORX" socket wrenches, remove the 3 stud bolts from the stiffening crankcase assembly.


d.
A314971

Using an E10 "TORX" socket wrench, remove the stud bolt from the cylinder block sub-assembly.


Hide 11401L 63.REMOVE REAR ENGINE OIL SEAL

a.
A196937

Remove the rear engine oil seal from the cylinder block sub-assembly.