Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2017.12–2021.02
RM33A0E _51 Engine / Hybrid System _065336 2GR-FKS INTAKE / EXHAUST _0328626 INTAKE MANIFOLD A

2GR-FKS INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A370417

Using an E8 "TORX" socket wrench, install the 2 stud bolts to the intake manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17177 2.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.

Install 2 new No. 1 intake manifold to head gaskets to each cylinder head sub-assembly.

NOTICE:
·

Align the port holes of the No. 1 intake manifold to head gaskets and cylinder head sub-assembly.

·

Make sure that the No. 1 intake manifold to head gaskets are installed in the correct direction.




Hide 17111 3.INSTALL INTAKE MANIFOLD

a.

Temporarily install the intake manifold to the cylinder head sub-assembly with the 4 bolts and 4 nuts.


b.
A408136C02
1.156,0.135 1.313,0.302 0.156,0.167 10 true 1 2.208,1.979 2.354,2.156 0.146,0.177 10 true 2 1.938,0.146 2.073,0.302 0.135,0.156 10 true 3 1.427,1.969 1.563,2.125 0.135,0.156 10 true 4 3.021,0.375 3.156,0.531 0.135,0.156 10 true 5 0.281,1.781 0.417,1.938 0.135,0.156 10 true 6 3.25,1.813 3.385,1.969 0.135,0.156 10 true 7 0.104,0.344 0.24,0.5 0.135,0.156 10 true 8
V100135

Bolt
V100136

Nut


Tighten the 4 bolts and 4 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23291 4.INSTALL INJECTOR VIBRATION INSULATOR

Hide 23800 6.INSTALL FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

Hide 12327A 8.INSTALL NO. 2 ENGINE MOUNTING STAY RH

a.
A408134

Install the No. 2 engine mounting stay RH to the intake manifold and front No. 1 engine mounting bracket LH with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.
A408135C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Install the No. 2 engine mounting stay RH to the engine mounting insulator sub-assembly RH with the bolt and 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Install the wire harness clamp bracket to the No. 2 engine mounting stay RH with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the wire harness clamp to the wire harness clamp bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11254 9.INSTALL NO. 1 V-BANK COVER BRACKET

HINT:

Perform this procedure only when replacement of the No. 1 V-bank cover bracket is necessary.


a.

Install the 2 No. 1 V-bank cover brackets to the intake air surge tank assembly.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 17176 10.INSTALL AIR SURGE TANK TO INTAKE MANIFOLD GASKET

a.

Install a new air surge tank to intake manifold gasket to the intake air surge tank assembly.


Hide 17190 11.INSTALL INTAKE AIR SURGE TANK ASSEMBLY

NOTICE:

Do not apply oil to the bolts and nuts as listed below:

Oil Application Prohibited Bolt and Nut
Bolt and Nut for Intake Air Surge Tank Assembly and Intake Manifold


a.

Install the plug to the intake air surge tank assembly.


b.

Temporarily install the intake air surge tank assembly to the intake manifold with the 5 bolts and 2 nuts.


c.

Temporarily install the No. 2 surge tank stay to the intake air surge tank assembly and camshaft housing RH with the 2 bolts.


d.
A408131C02
2.052,1.979 2.188,2.135 0.135,0.156 10 true 2 1.51,0.802 1.656,0.99 0.146,0.188 10 true 1 1.438,1.99 1.583,2.146 0.146,0.156 10 true 3 2.906,1.854 3.052,2.01 0.146,0.156 10 true 4 0.479,1.896 0.625,2.052 0.146,0.156 10 true 5 2.906,1.208 3.052,1.365 0.146,0.156 10 true 6 0.156,1.177 0.302,1.333 0.146,0.156 10 true 7
V100135

Bolt
V100136

Nut


Tighten the 5 bolts and 2 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.
A408128N01
1.906,1.76 2.063,1.958 0.156,0.198 10 true 1 2.198,1.073 2.354,1.271 0.156,0.198 10 true 2

Tighten the 2 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


f.
A415509C01
2.354,1.104 2.635,1.281 2.635,1.281 2.635,1.542 true 1.875,1.802 1.875,1.354 true 1.271,1.75 1.271,1.104 true 1.885,4.104 1.885,3.656 true 2.323,3.438 2.604,3.615 2.604,3.615 2.604,3.875 true 1.26,4.073 1.26,3.427 true 0.021,0.052 0.354,0.302 0.333,0.25 12 true *A 0.01,2.417 0.313,2.635 0.302,0.219 12 true *B 2.563,1.573 2.771,1.781 0.208,0.208 10 true *1 1.198,1.781 1.396,1.969 0.198,0.188 10 true *2 1.792,1.833 2.01,2.042 0.219,0.208 10 true *3 1.802,4.135 2.021,4.344 0.219,0.208 10 true *3 2.51,3.906 2.719,4.115 0.208,0.208 10 true *1 1.188,4.083 1.385,4.271 0.198,0.188 10 true *2
*A for LHD
*B for RHD
*1 Vacuum Hose Sub-assembly
*2 Vacuum Hose
*3 No. 2 Air Tube


Engage the clamp to connect the No. 2 air tube to the intake air surge tank assembly.


g.

Engage the clamp to connect the vacuum hose to the intake air surge tank assembly.


h.

Engage the 2 clamps to connect the vacuum hose sub-assembly to the intake air surge tank assembly.


i.
A408129

Engage the 2 clamps to connect the vacuum hose sub-assembly to the intake air surge tank assembly.


j.

Connect the vacuum hose sub-assembly to the vacuum switching valve (for ACIS).


k.

Connect the vacuum switching valve (for ACIS) connector.


Hide 25860 12.CONNECT PURGE VALVE (PURGE VSV)

a.

Connect the purge valve (purge VSV) to the intake air surge tank assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the No. 1 fuel vapor feed hose to the intake air surge tank assembly.


Hide 12261 13.CONNECT VENTILATION HOSE

a.

Connect the ventilation hose to the intake air surge tank assembly and slide the clip to secure it.


Hide 22030 14.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 53607A 15.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for LHD)

Hide 53607A 16.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for RHD)

Hide 55708 17.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 11209 20.INSTALL V-BANK COVER SUB-ASSEMBLY