Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › from 2017.12
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0344647 SFI SYSTEM(w/o Canister Pump Module) J

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  Active Control Engine Mount System  


DESCRIPTION

LOCATION
A402061C01
3.573,4.427 3.271,4.427 3.271,4.427 2.823,3.844 true 1.563,3.604 2.365,3.604 false 4.688,2.542 5.219,2.927 5.219,2.927 5.51,2.927 true 3.635,4.354 3.948,4.552 0.313,0.198 10 false *1 5.573,2.844 5.885,3.042 0.313,0.198 10 false *3 1.396,3.521 1.708,3.719 0.313,0.198 10 false *2
*1 Vacuum Switching Valve (for Active Control Engine Mount System) *2 Front Engine Mounting Insulator
*3 Rear Engine Mounting Insulator - -



The active control engine mount system decreases engine vibration at a low engine speed using the vacuum switching valve (for active control engine mount system). The vacuum switching valve (for active control engine mount system) is controlled by a pulse signal transmitted to the vacuum switching valve (for active control engine mount system) from the ECM. The frequency of this pulse signal is matched to the engine speed to decrease engine vibration.

WIRING DIAGRAM

A403543E06
3.354,1.646 5.542,2.135 2.188,0.49 10 false Vacuum Switching Valve (for Active Control Engine Mount System) 3.458,1.49 3.938,1.719 0.479,0.229 10 false C15 3.615,1.063 4.094,1.292 0.479,0.229 10 false 1 4.885,1.063 5.365,1.292 0.479,0.229 10 false 2 3.792,1.073 4.271,1.302 0.479,0.229 10 false +B 4.49,1.073 4.969,1.302 0.479,0.229 10 false ACM 0.583,3.76 1.24,4.01 0.656,0.25 10 false Battery 5.365,0.99 5.844,1.219 0.479,0.229 10 false 44 5.333,1.188 5.813,1.417 0.479,0.229 10 false C57 5.333,2.927 5.813,3.156 0.479,0.229 10 false A24 5.667,2.823 6.146,3.052 0.479,0.229 10 false MREL 0.458,3.063 1.115,3.313 0.656,0.25 10 false FL MAIN 0.458,2.167 1.552,2.438 1.094,0.271 10 false EFI-MAIN NO. 1 1.51,1.958 2.604,2.229 1.094,0.271 10 false EFI-MAIN NO. 1 2.625,1.323 3.719,1.594 1.094,0.271 10 false EFI NO. 1 1.583,1.073 2.677,1.344 1.094,0.271 10 false 3 1.594,1.563 2.688,1.833 1.094,0.271 10 false 1 2.271,1.073 3.365,1.344 1.094,0.271 10 false 5 2.271,1.573 3.365,1.844 1.094,0.271 10 false 2 5.667,1.073 6.146,1.302 0.479,0.229 10 false ACM 6.042,3.885 6.521,4.115 0.479,0.229 10 false ECM 6.302,2.969 6.615,3.229 0.313,0.26 10 false IC 5.365,2.729 5.844,2.958 0.479,0.229 10 false 15

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE ACM INHIBIT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the ACM Inhibit.

Powertrain > Engine > Active Test
Tester Display
Activate the ACM Inhibit
50004 372 43

e.

According to the display on the GTS, perform the Active Test to operate the vacuum switching valve (for active control engine mount system) and for check the operating sound of the vacuum switching valve (for active control engine mount system).

OK:

Operating sounds can be heard.



Result:
Proceed to
OK
NG



OK

2.CHECK VACUUM HOSES

NG

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM))
2.CHECK VACUUM HOSES
A403546C01
2.01,1.406 2.333,1.688 0.323,0.281 10 false *1 2.021,0.385 2.344,0.667 0.323,0.281 10 false *2 1.115,2.594 1.438,2.875 0.323,0.281 10 false *3 2.948,2.594 3.271,2.875 0.323,0.281 10 false *4 0.281,1.813 0.604,2.094 0.323,0.281 10 false *5 1.135,1.813 1.458,2.094 0.323,0.281 10 false *6
*1 Engine
*2 Vacuum Pump Assembly
*3 Front Engine Mounting Insulator
*4 Rear Engine Mounting Insulator
*5 ECM
*6 Vacuum Switching Valve (for Active Control Engine Mount System)


a.

Check the air and vacuum hoses for looseness, disconnection and blockage.

OK:

No looseness, disconnection or blockage.



Result:
Proceed to
OK
NG



OK

3.CHECK VACUUM

NG

REPAIR OR REPLACE VACUUM HOSES

3.CHECK VACUUM
A403542

a.

Disconnect the vacuum hose from the vacuum pump assembly.


b.

Start the engine.


c.

Check that the disconnected port located on the vacuum pump assembly applies suction to your finger.

OK:

Vacuum exists.



Result:
Proceed to
OK
NG



OK

4.INSPECT FRONT ENGINE MOUNTING INSULATOR

NG

REPLACE VACUUM PUMP ASSEMBLY

4.INSPECT FRONT ENGINE MOUNTING INSULATOR

Result:
Proceed to
OK
NG



OK

5.INSPECT REAR ENGINE MOUNTING INSULATOR

NG

5.INSPECT REAR ENGINE MOUNTING INSULATOR

Result:
Proceed to
OK
NG



OK

SYSTEM NORMAL

NG

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM))
A337501C16
0.552,1.188 0.896,1.438 0.344,0.25 1.094,1.781 1.51,1.365 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 0.604,1.229 0.917,1.427 0.313,0.198 10 false C15 0.885,1.719 1.198,1.917 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Vacuum Switching Valve (for Active Control Engine Mount System))


a.

Disconnect the vacuum switching valve (for active control engine mount system) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C15-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM)

NG

7.INSPECT VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM)
a.

Inspect the vacuum switching valve (for active control engine mount system).

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>VACUUM SWITCHING VALVE (for Engine Mounting)>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM) - ECM)

NG

REPLACE VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM)

8.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM) - ECM)
a.

Disconnect the vacuum switching valve (for active control engine mount system) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C15-2 (ACM) - C57-44 (ACM) Always Below 1 Ω
C15-2 (ACM) or C57-44 (ACM) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR