Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2018.04–2021.02
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0327417 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1422  Compressor Lock  


DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.

The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. If the difference becomes excessively large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnet clutch assembly off.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1422 Compressor Lock Open or short in A/C lock sensor circuit
·

Magnet clutch assembly

·

Harness or connector

·

Air conditioning amplifier assembly


Memorized
(3 sec. or more)

HINT:

The air conditioning amplifier assembly stores the DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E374540E01
2.573,1.656 3,1.854 0.427,0.198 10 false SSR+ 2.594,2.156 3.021,2.354 0.427,0.198 10 false SSR- 3.063,1.667 3.49,1.865 0.427,0.198 10 false 1 3.063,2.156 3.49,2.354 0.427,0.198 10 false 2 1.198,2.74 2.885,2.948 1.688,0.208 10 false Magnet Clutch Assembly 1.188,2.594 1.5,2.781 0.313,0.188 10 false C63 5.021,2.844 5.333,3.031 0.313,0.188 10 false K55 5.031,3.01 6.573,3.365 1.542,0.354 10 false Air Conditioning Amplifier Assembly 5.104,2.156 5.531,2.354 0.427,0.198 10 false 2 5.031,1.667 5.458,1.865 0.427,0.198 10 false 21 5.313,2.156 5.667,2.344 0.354,0.188 10 false SG-2 5.313,1.677 5.719,1.875 0.406,0.198 10 false LOCK 5.948,1.781 6.156,1.979 0.208,0.198 10 false IC 2.5,1.104 2.906,1.302 0.406,0.198 10 false ECM 0.563,3.344 2.25,3.552 1.688,0.208 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

The air conditioning system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the air conditioning system after confirming that the communication system is functioning properly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

ECM malfunctions can affect the storage of this DTC. Therefore, check all SFI system DTCs and confirm that the system is normal before performing the following inspection.

for 6AR-FSE: Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the air conditioning amplifier assembly, make sure to perform Initialization Servo Motor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>INITIALIZATION



PROCEDURE

1.INSPECT MAGNET CLUTCH ASSEMBLY


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the K55 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C63-1 (SSR+) - K55-21 (LOCK) Always Below 1 Ω
C63-2 (SSR-) - K55-2 (SG-2) Always Below 1 Ω
C63-1 (SSR+) or K55-21 (LOCK) - Other terminals and body ground Always 10 kΩ or higher
C63-2 (SSR-) or K55-2 (SG-2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR