Home › Engine / Hybrid System › 6AR-FSE (FUEL) › FUEL INJECTOR (for Port Injection) › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072204 6AR-FSE FUEL _0353735 FUEL INJECTOR(for Port Injection) A

6AR-FSE FUEL  FUEL INJECTOR(for Port Injection)  INSTALLATION  


PROCEDURE

Hide 23250F 1.INSTALL PORT FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a port fuel injector assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Apply a light coat of spindle oil or gasoline to a new O-ring, and install one to each port fuel injector assembly.

NOTICE:

Check that there is no damage or foreign matter on the groove of the port fuel injector assembly when installing each O-ring to the port fuel injector assembly.



b.
A411918C01
0.885,1.063 1.292,1.063 true 1.5,1.01 1.906,1.01 true 1.427,1.083 1.729,1.427 1.729,1.427 1.906,1.427 true 1.969,1.344 2.281,1.5 0.313,0.156 10 false *a 0.708,0.979 1.021,1.135 0.313,0.156 10 false *b 1.979,0.927 2.292,1.083 0.313,0.156 10 false *b
*a Claw
*b Stopper


Install the 4 port fuel injector assemblies to the fuel delivery pipe.

NOTICE:
·

Make sure that the port fuel injector assembly is located within the stopper as shown in the illustration.

·

Check that the port fuel injector assembly installation holes of the fuel delivery pipe are not damaged and are free of foreign matter.

·

Make sure that the O-ring is not damaged, twisted or moved out of place when installing the port fuel injector assembly.




Hide 23291 2.INSTALL INJECTOR VIBRATION INSULATOR

a.

Install 4 new injector vibration insulators to the cylinder head sub-assembly.


Hide 23891 3.INSTALL FUEL DELIVERY SPACER

a.

Install the 2 fuel delivery spacers to the cylinder head sub-assembly.


Hide 23814B 4.INSTALL FUEL DELIVERY PIPE

a.

Place the fuel delivery pipe with the port fuel injector assemblies onto the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the port fuel injector assemblies when installing the fuel delivery pipe.



b.

Install the fuel delivery pipe with the port fuel injector assemblies with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 82128A 5.CONNECT NO. 8 ENGINE WIRE

a.

Engage the 3 clamps to connect the No. 8 engine wire to the fuel delivery pipe.


b.

Connect the 4 port fuel injector assembly connectors.


Hide 12262 6.CONNECT NO. 2 VENTILATION HOSE

Hide 23901 7.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel delivery pipe.

Click hereEngine / Hybrid System>6AR-FSE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23801P 8.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23021 9.INSTALL FUEL PUMP WITH SEAL SUB-ASSEMBLY

Hide 23801P 10.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 22030 11.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 13.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 15.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a port fuel injector assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION