The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering column assembly removal/installation are shown below.
1. PRECAUTION
2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
45130
3.REMOVE HORN BUTTON ASSEMBLY
4.REMOVE STEERING WHEEL ASSEMBLY
45024
5.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY
Removing the lower steering column cover sub-assembly in the incorrect order will cause the parts to break.
Release the tilt and telescopic lever and fully extend and lower the steering column assembly.
Lock the tilt and telescopic lever.
Remove the 3 screws.
|
Push Area |
|
Push in this Direction |
While pressing the push area shown in the illustration to disengage the 2 claws, slightly lower the lower steering column cover sub-assembly.
45286B
6.REMOVE UPPER STEERING COLUMN COVER
|
Separate in this direction |
Disengage the claw and separate the upper steering column cover.
Disengage the 2 claws and 4 clips to remove the upper steering column cover.
89782
7.REMOVE TRANSPONDER KEY COIL (w/o Entry and Start System)
Disconnect the connector.
Disengage the 2 claws and remove the transponder key coil.
8.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.
Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.
Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.
| *a | Clamp |
Using pliers, expand the clamp.
While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.
67914
9.REMOVE FRONT DOOR SCUFF PLATE
62112A
10.REMOVE COWL SIDE TRIM SUB-ASSEMBLY
62312B
11.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
Disconnect the front door opening trim weatherstrip.
Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the instrument side panel.
55318C
12.REMOVE INSTRUMENT SIDE PANEL
55606
13.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
for LHD: Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
for RHD: Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
55436B
14.REMOVE NO. 2 METER HOOD CLUSTER
53601
15.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
55435B
16.REMOVE NO. 1 METER HOOD CLUSTER
55434B
17.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL
55302D
18.REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
w/ Driver Side Knee Airbag: Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
w/o Driver Side Knee Airbag: Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
73900
19.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)
87211
20.REMOVE NO. 1 AIR DUCT (for LHD)
| *a | View A |
|
Front |
Remove the 2 bolts.
Disengage the 3 claws to remove the No. 1 air duct.
Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct.
87211
21.REMOVE NO. 1 AIR DUCT (for RHD)
| *a | View A |
|
Front |
Remove the 2 bolts.
Disengage the 3 claws to remove the No. 1 air duct.
Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct.
22.REMOVE FRONT WHEEL LH (for LHD)
23.REMOVE FRONT WHEEL RH (for RHD)
45220
24.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY
45253
25.REMOVE STEERING COLUMN HOLE COVER
Turn back the floor carpet.
Remove the clip.
Disengage the 2 clips to remove the steering column hole cover.
45220
26.REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY
Using a screwdriver, loosen the clamp as shown in the illustration.
| *a | Matchmark |
Remove the bolt and slide the steering intermediate shaft assembly.
Do not remove the steering intermediate shaft assembly from the steering column assembly.
Put matchmarks on the steering intermediate shaft assembly and steering column assembly.
Remove the steering intermediate shaft assembly from the steering column assembly.
45250
27.REMOVE STEERING COLUMN ASSEMBLY
Disconnect each connector and disengage each wire harness clamp from the steering column assembly.
Remove the bolt, 2 nuts and steering column assembly.