The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.
| *a | An Object Exceeding Weight Limit of Engine Lifter |
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
1. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
3. DISCHARGE FUEL SYSTEM PRESSURE
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
5. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
6.SECURE STEERING WHEEL
7.REMOVE FRONT WHEELS
53851M
8.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
Remove the 3 screws and front wheel opening extension pad RH.
53852K
9.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
Remove the 3 screws and front wheel opening extension pad LH.
51441
10.REMOVE NO. 1 ENGINE UNDER COVER
Remove the bolt, 2 clips, 6 screws and No. 1 engine under cover.
11.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
Remove the 4 screws, 6 clips and No. 2 engine under cover assembly.
53737B
12.REMOVE FRONT FENDER APRON SEAL LH
Remove the 2 screws, clip and front fender apron seal LH.
53736
13.REMOVE FRONT FENDER APRON SEAL RH
Remove the 2 screws, clip and front fender apron seal RH.
52119A
14.REMOVE FRONT BUMPER COVER
52618
15.REMOVE FRONT LOWER BUMPER ABSORBER
Remove the 4 bolts.
Disengage the 2 claws to remove the front lower bumper absorber.
16.DRAIN ENGINE COOLANT
17.DRAIN ENGINE OIL
18.DRAIN AUTOMATIC TRANSAXLE FLUID
12601B
19.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
Lift the front of the No. 1 engine cover sub-assembly to disengage the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to disengage the clip and remove the No. 1 engine cover sub-assembly.
Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.
17750A
20.REMOVE INLET AIR CLEANER ASSEMBLY
Remove the 2 bolts and inlet air cleaner assembly.
21.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
| *a | Pin |
Disconnect the mass air flow meter sub-assembly connector.
Disengage the 3 wire harness clamps.
Slide the clip and disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.
Disengage the vacuum hose from the air cleaner hose.
Lock the hose clip.
Disengage the 3 pins and remove the air cleaner assembly with air cleaner hose.
Make sure the 3 air cleaner supports remain attached to the vehicle body.
89661
22.REMOVE ECM
23.REMOVE BATTERY
74404A
24.REMOVE BATTERY CLAMP SUB-ASSEMBLY
Disengage the 4 clamps from the battery clamp sub-assembly.
Remove the 3 bolts and battery clamp sub-assembly.
33820B
25.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
| *a | Clip |
| *b | 45° to 60° |
While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.
Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.
23826
26.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE
Slide the clip and disconnect the No. 1 fuel vapor feed hose from the No. 1 vacuum switching valve assembly.
44773F
27.DISCONNECT UNION TO CHECK VALVE HOSE
Slide the clip and disconnect the union to check valve hose from the vacuum pump assembly.
87246
28.DISCONNECT OUTLET HEATER HOSE
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to disengage the lock claws and pull off the outlet heater hose.
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater hose connector with plastic bags to prevent damage and contamination.
87245
29.DISCONNECT INLET HEATER HOSE
| *a | Retainer |
|
Pull out |
|
Pull off |
Pull out the retainer to disengage the lock claws and pull off the inlet heater hose.
Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.
Cover the disconnected flow shutting valve (water by-pass hose assembly) and inlet heater hose connector with plastic bags to prevent damage and contamination.
23901
30.DISCONNECT FUEL TUBE SUB-ASSEMBLY
Remove the No. 1 fuel pipe clamp from the fuel tube connector.
Disconnect the fuel tube sub-assembly.
Disconnect the fuel tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
16571C
31.DISCONNECT NO. 1 RADIATOR HOSE
Remove the clamp to disconnect the No. 1 radiator hose from the No. 1 radiator bracket.
Slide the clip and disconnect the No. 1 radiator hose from the water outlet.
16572D
32.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clip and disconnect the No. 2 radiator hose from the water inlet.
88711
33.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY
88704
34.DISCONNECT SUCTION HOSE SUB-ASSEMBLY
35.DISCONNECT WIRE HARNESS
After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.
Remove the engine room relay block and junction block assembly cover from the engine room relay block and junction block assembly.
Remove the nut from the engine room relay block and junction block assembly.
Disconnect the 4 connectors from the engine room relay block and junction block assembly.
Using a screwdriver, disengage the claw and separate the wire harness from the engine room relay block and junction block assembly.
Disengage the 3 clamps.
Remove the nut and disconnect the wire harness from the positive (+) battery terminal.
Remove the bolt and disconnect earth wire from the automatic transaxle assembly.
Remove the bolt and disconnect the wire harness from the vehicle body.
16281F
36.DISCONNECT NO. 5 WATER BY-PASS HOSE
Slide the clip and disconnect the No. 5 water by-pass hose from the No. 3 water by-pass pipe.
Disengage the clamp.
45220
37.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY
17410
38.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
39.REMOVE FRONT DRIVE SHAFT ASSEMBLY
40.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
Set the engine assembly with transaxle on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.
Disengage the clamp.
Remove the 6 bolts and body mounting plate.
Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.
Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket sub-assembly LH.
|
Bolt |
|
Nut |
Remove the 8 bolts and front bumper extension sub-assembly RH and front bumper extension sub-assembly LH from the front frame assembly and vehicle body.
Remove the 4 bolts, 2 nuts and front suspension member bracket sub-assembly RH and front suspension member bracket sub-assembly LH from the front frame assembly and vehicle body.
Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.
23825
41.REMOVE FUEL DELIVERY GUARD
Remove the bolt and fuel delivery guard from the engine mounting bracket RH.
42.INSTALL ENGINE HANGERS
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.
| No. 1 Engine Hanger | 12281-25030 |
| No. 2 Engine Hanger | 12282-25010 |
| Bolt | 91552-F1040 |
Using an engine sling device and engine lift, secure the engine assembly with transaxle.
Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
11361J
43.REMOVE FLYWHEEL HOUSING UNDER COVER
Remove the flywheel housing under cover from the cylinder block sub-assembly.
32101A
44.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
45.DISCONNECT VACUUM HOSE
16261G
46.REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)
16260
47.DISCONNECT WATER BY-PASS HOSE ASSEMBLY
35104V
48.REMOVE BREATHER PLUG HOSE
45319
49.REMOVE STEERING GEAR HEAT INSULATOR
50.DISCONNECT WIRE HARNESS
51100G
51.REMOVE FRONT FRAME ASSEMBLY
Remove the bolt and separate the front engine mounting insulator from the front engine mounting bracket.
Remove the 4 nuts and separate the rear engine mounting insulator from the front frame assembly.
12361A
52.REMOVE FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Remove the 3 nuts and front engine mounting insulator from the front frame assembly.
12371A
53.REMOVE REAR ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the rear engine mounting insulator is necessary.
Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>ACTIVE CONTROL ENGINE MOUNT (for Rear Side)>REMOVAL
12311A
54.REMOVE FRONT ENGINE MOUNTING BRACKET
Remove the 3 bolts and front engine mounting bracket from the transaxle housing.
11363A
55.REMOVE FLYWHEEL HOUSING SIDE COVER
28100
56.REMOVE STARTER ASSEMBLY
30500
57.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY
32101
58.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
19315
59.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
82121
60.REMOVE ENGINE WIRE
Remove the engine wire from the engine assembly.
61.INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Install the engine assembly to an engine stand.
62.REMOVE ENGINE HANGERS
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.
12305
63.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
Disconnect the No. 6 water by-pass hose.
Disengage the clamp.
Remove the bolt, nut and the radiator reserve tank assembly.
Remove the bolt and disconnect the bracket from the engine mounting insulator sub-assembly RH.
Remove the bolt and disconnect the No. 1 bond cable from the engine mounting insulator sub-assembly RH.
Disengage the clamp.
Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH.
12341
64.REMOVE ENGINE MOUNTING SPACER
Perform this procedure only when replacement of the engine mounting spacer is necessary.
Remove the 2 bolts and engine mounting spacer from the vehicle body.
12304
65.REMOVE ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH
Perform this procedure only when replacement of the engine mounting bracket sub-assembly LH is necessary.
Remove the 4 bolts and engine mounting bracket sub-assembly LH from the vehicle body.
12372A
66.REMOVE ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE ASSEMBLY>REMOVAL