Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › 2018.08–2019.10
RM33A0E _55 Steering _065372 STEERING GEAR / LINKAGE _0319589 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rack and pinion power steering gear assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on for 2AR-FE:(Click here)
for A25A-FKS (w/ Canister Pump Module):(Click here)
for A25A-FKS (w/o Canister Pump Module):(Click here)
for 2GR-FKS:(Click here)
for 6AR-FSE:(Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


for 2AR-FE:(Click here)
for A25A-FKS (w/ Canister Pump Module):(Click here)
for A25A-FKS (w/o Canister Pump Module):(Click here)
for 2GR-FKS:(Click here)
for 6AR-FSE:(Click here)
Replacement of automatic transaxle assembly
1.

Reset memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for UA80E Initialization:(Click here)
for UA80E Registration:(Click here)
for UB80E Initialization:(Click here)
for UB80E Registration:(Click here)
for U760E Initialization:(Click here)
for U760E Registration:(Click here)
for U761E Initialization:(Click here)
for U761E Registration:(Click here)
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system for Initialization:(Click here)
for Calibration:(Click here)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system for Initialization:(Click here)
for Calibration:(Click here)
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Rack and pinion power steering gear assembly
·

Perform torque sensor zero point calibration

·

Assist Map Writing


·

DTCs are output

·

Steering effort different between turning steering wheel left and right

·

EPS warning light illuminates


(Click here)

PROCEDURE

Hide 1. PRECAUTION

a.

When handling the rack and pinion power steering gear assembly:

i.

Do not subject the rack and pinion power steering gear assembly (especially the motor and torque sensor) to any impact. Replace the rack and pinion power steering gear assembly with a new one if subjected to a strong impact.


ii.

Do not pull the wire harness when moving the rack and pinion power steering gear assembly.


iii.

When the rack and pinion power steering gear assembly has been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION



b.

When disconnecting or reconnecting the connectors:

i.

Before disconnecting connectors related to the power steering system, turn the ignition switch to ON, center the steering wheel, turn the ignition switch off, and then disconnect the connectors.


ii.

Before reconnecting connectors related to the power steering system, ensure that the ignition switch is off. Then center the steering wheel and turn the ignition switch to ON.

NOTICE:

Do not turn the ignition switch to ON when the steering wheel is not centered.



iii.

If the above operations are not carried out properly, the steering center point (zero point) will deviate, which may lead to a difference in steering effort between turning right and left.

HINT:

If there is a difference in steering effort between turning right and left, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION




Hide 2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3. SECURE STEERING WHEEL

a.
C369774

Secure the steering wheel with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



Hide 4.REMOVE FRONT WHEELS

Hide 53852K 5.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (for A25A-FKS)

Hide 53851M 6.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (for A25A-FKS)

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER (for A25A-FKS)

Hide 51442 8.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY (for A25A-FKS)

Hide 45220 9.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C369775C01
0.958,2.823 1.531,2.823 true 1.115,2.833 1.115,2.906 1.115,2.906 1.469,2.906 true 0.792,2.74 0.958,2.906 0.167,0.167 10 true *a
*a Matchmark


Remove the bolt and slide the steering intermediate shaft assembly.

NOTICE:

Do not separate the steering intermediate shaft assembly from the rack and pinion power steering gear assembly.



b.

Put matchmarks on the rack and pinion power steering gear assembly and steering intermediate shaft assembly.


c.

Separate the steering intermediate shaft assembly from the rack and pinion power steering gear assembly.


Hide 45470 10.SEPARATE TIE ROD ASSEMBLY LH

a.
C369776

Remove the cotter pin and nut.


b.
C369777N01
2.375,1.052 2.375,0.646 2.375,0.646 2.479,0.646 false 2.521,0.563 2.979,0.76 0.458,0.198 10 false SST

Install SST to the tie rod assembly LH as shown in the illustration.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the upper ends of the tie rod assembly LH and SST are aligned.



c.

Using SST, separate the tie rod assembly LH from the steering knuckle LH as shown in the illustration.

SST
09960-20010  (09961-02010)

C369778C01
0.448,0.25 0.552,0.25 0.552,0.25 0.792,0.563 true 1.198,2.146 1.385,2.531 1.385,2.531 1.479,2.531 false 3.396,2.583 3.49,2.583 3.49,2.583 3.865,1.875 false 0.271,0.156 0.458,0.323 0.188,0.167 10 true *a 5.521,0.344 5.833,0.5 0.313,0.156 10 false *b 6.542,2.323 6.854,2.479 0.313,0.156 10 false *c 1.51,2.448 1.823,2.604 0.313,0.156 10 false *d 5.521,0.656 5.833,0.813 0.313,0.156 10 false *b 0.323,1.688 0.635,1.844 0.313,0.156 10 false A 0.323,1.917 0.635,2.073 0.313,0.156 10 false B 3.094,2.5 3.552,2.698 0.458,0.198 10 false SST
*a String *b Molybdenum Grease Application Area
*c Place wrench here *d Center Nut
V113147

Turn - -


CAUTION:

Apply molybdenum grease to the threads and end of the SST bolt.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.

·

Be sure to place the wrench on the part shown in the illustration.

·

Do not damage the front disc brake dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle LH.




Hide 45460 11.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45319 13.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

a.

for A25A-FKS:

i.
C369782

Remove the 2 bolts and steering gear heat insulator from the rack and pinion power steering gear assembly.



Hide 14.DISCONNECT WIRE HARNESS (for LHD)

a.

Disconnect the wire harness connector from the rack and pinion power steering gear assembly.

HINT:

Release the lock before rotating the lock lever.


C374274


b.

Remove the 2 bolts and separate the wire harness from the rack and pinion power steering gear assembly.


Hide 15.DISCONNECT WIRE HARNESS (for RHD)

a.

Disconnect the wire harness connector from the rack and pinion power steering gear assembly.

HINT:

Release the lock before rotating the lock lever.


C378551


b.

Remove the bolt and separate the wire harness from the rack and pinion power steering gear assembly.


Hide 23825 16.REMOVE FUEL DELIVERY GUARD (for A25A-FKS)

Hide 18.REMOVE FRONT FRAME ASSEMBLY

Hide 19.REMOVE FRONT STABILIZER BAR WITH BRACKET (for A25A-FKS)

a.
C373248

Remove the 2 bolts and separate the front No. 1 stabilizer bracket LH from the front frame assembly.


b.
C402497

Remove the 2 bolts and separate the front No. 1 stabilizer bracket RH from the front frame assembly.


c.

Remove the front stabilizer bar with the 2 front stabilizer links, front No. 1 stabilizer bracket LH, front No. 1 stabilizer bracket RH and 2 front No. 1 stabilizer bar bushings from the front frame assembly.


Hide 20.REMOVE FRONT STABILIZER BAR WITH BRACKET (for 2GR-FKS, 2AR-FE, 6AR-FSE)

a.
C380745C03
0.031,0.146 0.313,0.365 0.281,0.219 12 true *A 0.031,2.479 0.313,2.698 0.281,0.219 12 true *B
*A for TMC Made
*B for TMR Made


Remove the 2 bolts and separate the front No. 1 stabilizer bracket LH from the front frame assembly.


b.

Remove the 2 bolts and separate the front No. 1 stabilizer bracket RH from the front frame assembly.

HINT:

Perform the same procedure as for the LH side.



c.

Remove the front stabilizer bar with the 2 front stabilizer links, front No. 1 stabilizer bracket LH, front No. 1 stabilizer bracket RH and 2 front No. 1 stabilizer bar bushings from the front frame assembly.


Hide 44250 21.REMOVE RACK AND PINION POWER STEERING GEAR ASSEMBLY

a.
C369779

Remove the 4 bolts, 4 nuts and rack and pinion power steering gear assembly from the front frame assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 44250 22.SECURE RACK AND PINION POWER STEERING GEAR ASSEMBLY

a.
C369780C01
1.427,1.042 2.135,1.438 2.135,1.438 2.219,1.438 false 0.865,0.323 0.948,0.323 0.948,0.323 1.135,0.729 false 2.26,1.354 2.573,1.51 0.313,0.156 10 false *a 0.573,0.24 1.031,0.438 0.458,0.198 10 false SST
*a Protective Tape


Using SST, secure the rack and pinion power steering gear assembly in a vise.

SST
09612-00012  

HINT:

Wrap SST with protective tape before use.



Hide 45470 23.REMOVE TIE ROD ASSEMBLY LH

a.
C369781C01
2.198,1.094 2.198,0.396 false 1.969,0.396 2.406,0.396 2.406,0.396 2.406,1.094 false 1.813,0.302 2.125,0.458 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the tie rod assembly LH and rack and pinion power steering gear assembly.


b.

Remove the tie rod assembly LH and lock nut.


Hide 45460 24.REMOVE TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45319 25.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

a.

for 2GR-FKS:

i.
C369783

Remove the 2 bolts and steering gear heat insulator from the rack and pinion power steering gear assembly.