Home › Suspension › FRONT SUSPENSION › FRONT STABILIZER BAR › 2019.10–2020.02
RM33A0E _53 Suspension _065361 FRONT SUSPENSION _0319584 FRONT STABILIZER BAR A

FRONT SUSPENSION  FRONT STABILIZER BAR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front stabilizer bar removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

*2: for TMC Made

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on for 2AR-FE:(Click here)
for A25A-FKS (w/ Canister Pump Module):(Click here)
for A25A-FKS (w/o Canister Pump Module):(Click here)
for 2GR-FKS:(Click here)
for 6AR-FSE:(Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


for 2AR-FE:(Click here)
for A25A-FKS (w/ Canister Pump Module):(Click here)
for A25A-FKS (w/o Canister Pump Module):(Click here)
for 2GR-FKS:(Click here)
for 6AR-FSE:(Click here)
Replacement of automatic transaxle assembly
1.

Reset memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for UA80E Initialization:(Click here)
for UA80E Registration:(Click here)
for UB80E Initialization:(Click here)
for UB80E Registration:(Click here)
for U760E Initialization:(Click here)
for U760E Registration:(Click here)
for U761E Initialization:(Click here)
for U761E Registration:(Click here)
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


for UA80E*2

Automatic transaxle fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
for UB80E

Automatic transaxle fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
for U760E

Automatic transaxle fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system for Initialization:(Click here)
for Calibration:(Click here)
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system for Initialization:(Click here)
for Calibration:(Click here)
Perform headlight ECU sub-assembly LH initialization Lighting system (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Rack and pinion power steering gear assembly
·

Perform torque sensor zero point calibration

·

Assist Map Writing


·

DTCs are output

·

Steering effort different between turning steering wheel left and right

·

EPS warning light illuminates


(Click here)

PROCEDURE

Hide 48810 2.REMOVE FRONT STABILIZER LINK ASSEMBLY LH

a.
C400795

w/ Cap:

i.

Remove the cap from the nut.



b.
C373247

Remove the nut and front stabilizer link assembly LH from the front stabilizer bar.

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 48820B 3.REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48829A 4.REMOVE FRONT NO. 1 STABILIZER BRACKET LH

a.
C380745C02
0.031,0.146 0.313,0.365 0.281,0.219 12 true *A 0.031,2.479 0.313,2.698 0.281,0.219 12 true *B
*A for TMC Made
*B for TMR Made


Remove the 2 bolts and front No. 1 stabilizer bracket LH from the front frame assembly.


Hide 48824A 5.REMOVE FRONT NO. 1 STABILIZER BRACKET RH (for A25A-FKS)

a.
C402497

Remove the 2 bolts and front No. 1 stabilizer bracket RH from the front frame assembly.


Hide 48824A 6.REMOVE FRONT NO. 1 STABILIZER BRACKET RH (for 2GR-FKS, 2AR-FE, 6AR-FSE)

HINT:

Perform the same procedure as for the LH side.


Hide 48811 7.REMOVE FRONT STABILIZER BAR

a.

Remove the front stabilizer bar with 2 front stabilizer bar bushings from the front frame assembly.


Hide 48815 8.REMOVE FRONT NO. 1 STABILIZER BAR BUSHING (for LH Side)

a.

Remove the front No. 1 stabilizer bar bushing from the front stabilizer bar.


Hide 48815 9.REMOVE FRONT NO. 1 STABILIZER BAR BUSHING (for RH Side)

HINT:

Perform the same procedure as for the LH side.