This DTC is stored when the combination meter assembly detects a short in a turn signal light circuit.
If there is a short in a turn signal light circuit, all of the turn signal lights in that circuit will not blink.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B150819 | Turn Signal/Hazard Flasher Circuit Current Above Threshold | Diagnosis Condition:
Battery voltage is 10 V or more Malfunction Status: Short in turn signal light circuit |
·
Headlight ECU sub-assembly*1 ·
Head light unit assembly*1 ·
Headlight lens*3 ·
Front turn signal light socket*2 ·
Side turn signal light assembly ·
Outer rear view mirror assembly*6 ·
Outer mirror retractor*7 ·
Rear combination light assembly*4 ·
Rear combination light cord*4 ·
Rear combination light socket and wire*5 ·
Harness or connector ·
Combination meter assembly |
DTC stored | - |
*1: w/ Automatic Headlight Beam Level Control System
*2: w/o Automatic Headlight Beam Level Control System
*3: for LED Type Turn Signal Light
*4: for LED Type Back-up Light
*5: for Bulb Type Back-up Light
*6: w/o Power Retract Mirror
*7: w/ Power Retract Mirror
LH SIDE
RH SIDE
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Inspect the turn signal light bulbs before performing the following procedure.
Inspect the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| All LH turn signal lights do not blink | A |
| All RH turn signal lights do not blink | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Automatic Headlight Beam Level Control System | A |
| w/o Automatic Headlight Beam Level Control System | B |
A
B
Disconnect the A10 headlight assembly LH connector.
Operate the headlight dimmer switch assembly and check that the LH side turn signal lights other than the headlight turn signal light blink.
If the LH side turn signal lights blink, the headlight assembly LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights blink | A |
| LH side turn signal lights do not blink | B |
A
B
| *a | Component without harness connected
(Headlight ECU Sub-assembly LH) |
- | - |
Remove the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-9 (TURN+) - B-13 (TURN-)
or A10-11 (TNS) - A10-12 (GND) |
Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Turn Signal Light | A |
| for Bulb Type Turn Signal Light | B |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Remove the headlight lens LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Inspect the headlight lens LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Disconnect the A76 headlight assembly LH connector.
Operate the headlight dimmer switch assembly and check that the LH side turn signal lights other than the headlight turn signal light blink.
If the LH side turn signal lights blink, the front turn signal light socket LH is malfunctioning.
| Result | Proceed to |
|---|---|
| LH side turn signal lights blink | A |
| LH side turn signal lights do not blink | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
B
Connect the A76 headlight assembly LH*1 connector.
Connect the A10 headlight assembly LH*2 connector.
Disconnect the O16 outer rear view mirror assembly LH*3 connector.
Disconnect the O20 outer rear view mirror assembly LH*4 connector.
Disconnect the O21 outer rear view mirror assembly LH*5 connector.
Disconnect the O22 outer rear view mirror assembly LH*6 connector.
Operate the headlight dimmer switch assembly and check that the LH side turn signal lights other than the side turn signal light blink.
If the LH side turn signal lights blink, the outer rear view mirror assembly LH is malfunctioning.
*1: w/o Automatic Headlight Beam Level Control System
*2: w/ Automatic Headlight Beam Level Control System
*3: for 11 Pin Connector
*4: for 7 Pin Connector
*5: for 16 Pin Connector
*6: for 22 Pin Connector
| Result | Proceed to |
|---|---|
| LH side turn signal lights blink | A |
| LH side turn signal lights do not blink | B |
A
B
Remove the side turn signal light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Inspect the side turn signal light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Power Retractable Mirror | A |
| w/ Power Retractable Mirror | B |
A
B
Connect the O16 outer rear view mirror assembly LH*1 connector.
Connect the O20 outer rear view mirror assembly LH*2 connector.
Connect the O21 outer rear view mirror assembly LH*3 connector.
Connect the O22 outer rear view mirror assembly LH*4 connector.
Disconnect the W13 rear combination light assembly LH connector.
Operate the headlight dimmer switch assembly and check that the LH side turn signal lights other than the rear turn signal light blink.
If the LH side turn signal lights blink, the rear combination light assembly LH is malfunctioning.
*1: for 11 Pin Connector
*2: for 7 Pin Connector
*3: for 16 Pin Connector
*4: for 22 Pin Connector
| Result | Proceed to |
|---|---|
| LH side turn signal lights blink | A |
| LH side turn signal lights do not blink | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Back-up Light | A |
| for Bulb Type Back-up Light | B |
A
B
Remove the rear combination light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL
Inspect the rear combination light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W13-3 (B) or K20-10 (TRNL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A76 headlight assembly LH*1 connector.
Disconnect the A10 headlight assembly LH*2 connector.
Disconnect the O16 outer rear view mirror assembly LH*3 connector.
Disconnect the O20 outer rear view mirror assembly LH*4 connector.
Disconnect the O21 outer rear view mirror assembly LH*5 connector.
Disconnect the O22 outer rear view mirror assembly LH*6 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A76-1 (B)*1, A10-11 (TNS)*2, O16-10(B)*3, O20-5 (B)*4, O21-16 (B)*5, O22-4 (B)*6 or K20-11 (LL) - Body ground | Always | 10 kΩ or higher |
*1: w/o Automatic Headlight Beam Level Control System
*2: w/ Automatic Headlight Beam Level Control System
*3: for 11 Pin Connector
*4: for 7 Pin Connector
*5: for 16 Pin Connector
*6: for 22 Pin Connector
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Automatic Headlight Beam Level Control System | A |
| w/o Automatic Headlight Beam Level Control System | B |
A
B
Disconnect the A11 headlight assembly RH connector.
Operate the headlight dimmer switch assembly and check that the RH side turn signal lights other than the headlight turn signal light blink.
If the RH side turn signal lights blink, the headlight assembly RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights blink | A |
| RH side turn signal lights do not blink | B |
A
B
| *a | Component without harness connected
(Headlight ECU Sub-assembly RH) |
- | - |
Remove the headlight ECU sub-assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-9 (TURN+) - B-13 (TURN-)
or A11-11 (TNS) - A11-12 (GND) |
Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Turn Signal Light | A |
| for Bulb Type Turn Signal Light | B |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Remove the headlight lens RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Inspect the headlight lens RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Disconnect the A75 headlight assembly RH connector.
Operate the headlight dimmer switch assembly and check that the RH side turn signal lights other than the headlight turn signal light blink.
If the RH side turn signal lights blink, the front turn signal light socket RH is malfunctioning.
| Result | Proceed to |
|---|---|
| RH side turn signal lights blink | A |
| RH side turn signal lights do not blink | B |
A
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
B
Connect the A75 headlight assembly RH*1 connector.
Connect the A11 headlight assembly RH*2 connector.
Disconnect the N19 outer rear view mirror assembly RH*3 connector.
Disconnect the N22 outer rear view mirror assembly RH*4 connector.
Disconnect the N23 outer rear view mirror assembly RH*5 connector.
Disconnect the N24 outer rear view mirror assembly RH*6 connector.
Operate the headlight dimmer switch assembly and check that the RH side turn signal lights other than the side turn signal light blink.
If the RH side turn signal lights blink, the outer rear view mirror assembly RH is malfunctioning.
*1: w/o Automatic Headlight Beam Level Control System
*2: w/ Automatic Headlight Beam Level Control System
*3: for 11 Pin Connector
*4: for 7 Pin Connector
*5: for 16 Pin Connector
*6: for 22 Pin Connector
| Result | Proceed to |
|---|---|
| RH side turn signal lights blink | A |
| RH side turn signal lights do not blink | B |
A
B
Remove the side turn signal light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL
Inspect the side turn signal light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Power Retractable Mirror | A |
| w/ Power Retractable Mirror | B |
A
B
Connect the N19 outer rear view mirror assembly RH*1 connector.
Connect the N22 outer rear view mirror assembly RH*2 connector.
Connect the N23 outer rear view mirror assembly RH*3 connector.
Connect the N24 outer rear view mirror assembly RH*4 connector.
Disconnect the W12 rear combination light assembly RH connector.
Operate the headlight dimmer switch assembly and check that the RH side turn signal lights other than the rear turn signal light blink.
If the RH side turn signal lights blink, the rear combination light assembly RH is malfunctioning.
*1: for 11 Pin Connector
*2: for 7 Pin Connector
*3: for 16 Pin Connector
*4: for 22 Pin Connector
| Result | Proceed to |
|---|---|
| RH side turn signal lights blink | A |
| RH side turn signal lights do not blink | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Back-up Light | A |
| for Bulb Type Back-up Light | B |
A
B
Remove the rear combination light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL
Inspect the rear combination light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W12-3 (B) or K20-13 (TRNR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A75 headlight assembly RH*1 connector.
Disconnect the A11 headlight assembly RH*2 connector.
Disconnect the N19 outer rear view mirror assembly RH*3 connector.
Disconnect the N22 outer rear view mirror assembly RH*4 connector.
Disconnect the N23 outer rear view mirror assembly RH*5 connector.
Disconnect the N24 outer rear view mirror assembly RH*6 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A75-1 (B)*1, A11-11 (TNS)*2, N19-10 (B)*3, N22-5 (B)*4, N23-16 (B)*5, N24-4 (B)*6 or K20-7 (LR) - Body ground | Always | 10 kΩ or higher |
*1: w/o Automatic Headlight Beam Level Control System
*2: w/ Automatic Headlight Beam Level Control System
*3: for 11 Pin Connector
*4: for 7 Pin Connector
*5: for 16 Pin Connector
*6: for 22 Pin Connector
| Proceed to |
|---|
| OK |
| NG |
OK
NG