The headlight ECU sub-assembly RH controls the headlight cleaner motor and pump assembly.
for LHD
for RHD
Check that the front washers are normal before performing the following procedure.
Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>OPERATION CHECK
Check that the lighting system is normal before performing the following procedure.
Inspect the fuses and relays for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter following menus: Body Electrical / HL AutoLeveling (Sub) / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Headlight Cleaner | Function to operate the headlight cleaner motor and pump assembly | OFF or ON | - |
| Tester Display |
|---|
| Headlight Cleaner |
Headlight cleaner motor and pump assembly is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling (Sub) / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Front Window Washer Switch | Windshield wiper switch assembly (washer switch) condition | OFF or ON | OFF: Windshield wiper switch assembly (washer switch) off
ON: Windshield wiper switch assembly (washer switch) on |
- |
| Tester Display |
|---|
| Front Window Washer Switch |
The GTS display is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the headlight cleaner motor and pump assembly.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>REMOVAL
Inspect the headlight cleaner motor and pump assembly.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the headlight cleaner control relay.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER CONTROL RELAY>REMOVAL
Inspect the headlight cleaner control relay.
Click hereVehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER CONTROL RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A8 headlight cleaner motor and pump assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A8-2 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A9 headlight cleaner control relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A8-1 (L) - A9-6 (PB) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A9-3 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A9-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A11 headlight ECU sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A84-7 (HLC) - A9-2 (H) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG