Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER › from 2021.02
RM33A0E _53 Suspension _065362 REAR SUSPENSION _0319641 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
·

Perform "Reset Memory"

·

Perform acceleration sensor zero point calibration and system information memorization


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)
Suspension, tires
(The vehicle height changes because of suspension or tire replacement.)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)for Initialization
(Click here)for Calibration
Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Rear height control sensor sub-assembly LH Perform headlight ECU sub-assembly LH initialization Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System) (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)for A25A-FKS (w/ Canister Pump Module)
(Click here)for A25A-FKS (w/o Canister Pump Module)
(Click here)M20A-FKS
(Click here)for 2GR-FKS

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 58399D 3.REMOVE NO. 2 FLOOR UNDER COVER (w/ Cover)

Hide 58398F 4.REMOVE NO. 1 FLOOR UNDER COVER (w/ Cover)

Hide 47319F 5.SEPARATE REAR FLEXIBLE HOSE LH

a.

Remove the bolt and separate the rear flexible hose LH from the rear flexible hose bracket.


Hide 47318F 6.SEPARATE REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as for the LH side.


Hide 89408C 7.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

Hide 48840A 8.REMOVE REAR STABILIZER LINK ASSEMBLY LH

Hide 48830D 9.REMOVE REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 10.REMOVE REAR STABILIZER BAR (for TMC Made)

Hide 48805 11.REMOVE REAR STABILIZER BAR SUB-ASSEMBLY (for TMR Made)

Hide 48231B 12.REMOVE REAR COIL SPRING LH

Hide 48231A 13.REMOVE REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48258C 14.REMOVE REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 15.REMOVE REAR LOWER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 16.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 17.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 18.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 19.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48790 20.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C376678

Remove the bolt and nut and separate the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48770A 21.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 51206A 22.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C370233C01
0.927,4.385 0.927,4 true 1.646,4.417 1.646,4.031 true 2.24,4.406 2.24,3.927 true 3.063,4.333 3.063,4.073 3.063,4.073 2.906,4.073 true 2.594,3.854 2.979,3.854 true 3,4.354 3.313,4.51 0.313,0.156 10 false *a 0.885,4.417 1.198,4.573 0.313,0.156 10 false *b 1.552,4.417 1.865,4.573 0.313,0.156 10 false *b 2.167,4.438 2.479,4.594 0.313,0.156 10 false *b 3,3.781 3.313,3.938 0.313,0.156 10 false *b
*a Engine Lifter
*b Attachment
V100155

Attachment Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
C370234

·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.



b.
C370235

Remove the 2 bolts, 6 nuts, 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH.


c.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



d.

Remove the 4 rear suspension member cushions from the rear suspension member sub-assembly.

HINT:

Make sure to place an identification mark on the rear suspension member cushion so that they can be reinstalled to their original positions.



Hide 48790 23.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 24.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 52271D 25.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

a.
C375044C01
2,1.677 2.469,1.677 false 0.979,0.49 1.448,0.49 false 2.51,1.594 2.823,1.75 0.313,0.156 10 false *a 0.802,0.396 1.115,0.552 0.313,0.156 10 false *a
*a Bend Portion


Using a chisel and hammer, bend the 2 portions of the rear suspension member front body mounting cushion rib.

NOTICE:

Make sure to bend the 2 portions of the cushion rib until the claws of SST can fit securely.



b.

Apply lubricant to the contact surfaces of the rear suspension member front body mounting cushion.


c.
C375054N01
1,0.448 1.646,0.448 false 0.885,1.813 1.271,1.813 false 0.667,0.354 1.125,0.552 0.458,0.198 10 false SST 0.594,1.719 1.052,1.917 0.458,0.198 10 false SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04010, 09952-04010, 09954-04010, 09955-04061, 09958-04011)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.



d.
C381738C03
1.458,0.583 1.625,0.583 1.625,0.583 1.99,0.865 false 2.396,1.729 2.698,1.729 false 0.792,1.885 1.083,2.104 0.292,0.219 10 false *a 1.167,0.5 1.469,0.677 0.302,0.177 10 false SST 2.74,1.646 3.042,1.823 0.302,0.177 10 false SST
*a Hold
V113147

Turn


Using SST, remove the rear suspension member front body mounting cushion while applying lubricant into the clearance between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04010, 09952-04010, 09954-04010, 09955-04061, 09958-04011)

NOTICE:
·

Set the claws of SST into the rear suspension member sub-assembly securely as shown in the illustration.

·

Tighten SST slowly and evenly.

·

Be careful as the rear suspension member front body mounting cushion may fly out.

·

The rear suspension member front body mounting cushion cannot be reused.




e.

Remove SST and the rear suspension member front body mounting cushion from the rear suspension member sub-assembly.


Hide 52271D 26.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 52276A 27.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH

a.
C375056N01
0.802,1.49 1.198,1.49 true 2.167,2.156 2.563,2.156 true 1.021,1.49 1.021,1.656 1.021,1.656 1.573,1.656 true 1.021,1.573 1.583,1.573 true 0.5,1.417 0.875,1.625 0.375,0.208 10 false SST 2.615,2.073 2.99,2.281 0.375,0.208 10 false SST

Install SST as shown in the illustration.

SST
09950-00020  
09950-00030  
09950-60011  (09951-00330)

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.



b.
C375057C01
1.948,1.865 2.406,1.865 false 0.479,0.698 0.698,0.698 0.698,0.698 1.094,0.938 true 0.563,1.854 0.865,1.854 0.865,1.854 1.448,1.375 true 0.75,1.854 1.448,1.302 false 0.271,1.292 0.583,1.448 0.313,0.156 10 false *a 2.479,1.792 2.938,1.99 0.458,0.198 10 false SST 0.177,0.615 0.635,0.813 0.458,0.198 10 false SST 0.271,1.771 0.729,1.969 0.458,0.198 10 false SST
*a Hold
V113147

Turn


Using SST, remove the rear suspension member rear body mount cushion LH while applying lubricant into the clearance between the rear suspension member rear body mount cushion LH and the rear suspension member sub-assembly.

SST
09950-00020  
09950-00030  
09950-60011  (09951-00330)

NOTICE:
·

Tighten SST slowly and evenly.

·

Be careful as the rear suspension member rear body mount cushion LH may fly out.

·

The rear suspension member rear body mount cushion LH cannot be reused.




c.

Remove SST and the rear suspension member rear body mount cushion LH from the rear suspension member sub-assembly.


Hide 52275B 28.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH

HINT:

Perform the same procedure as for the LH side.