This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1.INSTALL CAMSHAFT
Perform "Inspection After Repair" after replacing the intake camshaft sub-assembly, exhaust camshaft sub-assembly, camshaft timing gear assembly and camshaft timing exhaust gear assembly.
Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| *a | "0" Timing Mark |
| *b | Timing Mark |
Turn the crankshaft clockwise to align the timing mark (cutout) on the crankshaft pulley assembly with the "0" timing mark on the No. 2 timing chain cover assembly.
| *1 | No. 1 Valve Rocker Arm Sub-assembly |
| *2 | Valve Lash Adjuster Assembly |
| *3 | Valve Stem Cap |
Check that the No. 1 valve rocker arm sub-assembly is correctly installed as shown in the illustration.
Clean the camshaft housing sub-assembly and the cams and journals of the intake camshaft sub-assembly and exhaust camshaft sub-assembly, and then apply engine oil to them.
Apply a light coat of engine oil to the journals of the intake camshaft sub-assembly and install the intake camshaft sub-assembly to the camshaft housing sub-assembly.
Apply a light coat of engine oil to the journals of the exhaust camshaft sub-assembly and install the exhaust camshaft sub-assembly to the camshaft housing sub-assembly.
| *1 | No. 1 Camshaft Bearing Cap |
| *2 | No. 2 Camshaft Bearing Cap |
| *3 | No. 3 Camshaft Bearing Cap |
| *4 | No. 4 Camshaft Bearing Cap |
Set the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap as shown in the illustration.
Uniformly tighten the 13 bolts in the order shown in the illustration.
Uniformly tighten the 9 bolts in the order shown in the illustration.
Set the camshaft timing gear assembly and camshaft timing exhaust gear assembly to the chain sub-assembly as shown in the illustration.
| *a | Paint Mark |
| *b | Timing Mark |
Align the timing mark on the camshaft timing gear assembly with the paint mark on the chain sub-assembly.
| *a | Paint Mark |
| *b | Timing Mark |
Align the timing mark on the camshaft timing exhaust gear assembly with the paint mark on the chain sub-assembly.
| *a | Knock Pin |
Using the hexagonal portion of the intake camshaft sub-assembly, install the camshaft timing gear assembly to the intake camshaft sub-assembly.
Check that the knock pin matches the pin hole from the No. 2 timing chain cover sub-assembly side.
Using a 10 mm bi-hexagon socket wrench, temporarily install the camshaft timing gear assembly with the bolt.
Temporarily install the bolt enough that the camshaft timing gear assembly does not detach from the knock pin of the intake camshaft sub-assembly.
Using the hexagonal portion of the exhaust camshaft sub-assembly, install the camshaft timing exhaust gear assembly to the exhaust camshaft sub-assembly.
Temporarily install the 2 bolts.
The 2 bolts can only be installed as shown in the illustration if the knock pin on the exhaust camshaft sub-assembly and the pin hole on the camshaft timing exhaust gear assembly match. If the 2 bolts cannot be installed, the knock pin and pin hole do not match.
| *1 | No. 1 Chain Vibration Damper |
Check the status of the camshaft timing gear assembly and camshaft timing exhaust gear assembly temporarily installed to each camshaft.
Camshaft timing gear assembly side:
Check that the chain sub-assembly does not overlap the No. 1 chain vibration damper as shown in the illustration.
If the chain sub-assembly overlaps the No. 1 chain vibration damper, install it again.
| *1 | Chain Tensioner Slipper |
Camshaft timing exhaust gear assembly side:
Check that the chain sub-assembly does not overlap the chain tensioner slipper as shown in the illustration.
If the chain sub-assembly overlaps the chain tensioner slipper, install it again.
| *a | Hold |
Using the hexagonal portion of the intake camshaft sub-assembly, hold the intake camshaft sub-assembly.
Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.
Do not disassemble the camshaft timing gear assembly.
Using a 10 mm bi-hexagon socket wrench, tighten the bolt on the camshaft timing gear assembly.
| *a | Hold |
Using the hexagonal portion of the exhaust camshaft sub-assembly, hold the exhaust camshaft sub-assembly.
Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.
Do not disassemble the camshaft timing gear assembly.
Using a 5 mm hexagon wrench, tighten the 2 bolts.
| *a | Paint Mark |
| *b | Timing Mark |
Check that the paint marks and timing marks are positioned as shown in the illustration.
Using the hexagonal portion of the intake camshaft sub-assembly, check that the chain sub-assembly slackens when the intake camshaft sub-assembly is moved in the direction shown in the illustration.
| *a | Hold | - | - |
|
Turn | - | - |
If the chain sub-assembly remains tight and does not slacken, the chain tensioner slipper and No. 1 chain vibration damper may overlap the chain sub-assembly, so install them again.
Remove the pin from the No. 1 chain tensioner assembly.
2.INSTALL STRAIGHT SCREW PLUG
3.SET NO. 1 CYLINDER TO TDC (COMPRESSION)
23477
4.INSTALL FUEL PUMP LIFTER GUIDE
11193
5.INSTALL SPARK PLUG TUBE GASKET
11201
6.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
13090E
7.INSTALL CAM TIMING CONTROL MOTOR O-RING
13090D
8.INSTALL CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY
135A0B
9.INSTALL CAMSHAFT TIMING VALVE ASSEMBLY
15370
10.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
19500
11.INSTALL IGNITION COIL ASSEMBLY
29300
12.INSTALL VACUUM PUMP ASSEMBLY
for M20 Series Engine, BOSCH Made:
Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM PUMP (for M20 Series Engine, BOSCH Made)>INSTALLATION
for M20 Series Engine, except BOSCH Made:
Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM PUMP (for M20 Series Engine, except BOSCH Made)>INSTALLATION
23100X
13.INSTALL FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)
14.INSTALL ENGINE HANGERS
15.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND