After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and system information memorization.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Brake pedal inspection
Perform a visual inspection and operate the brake pedal to check for any malfunctions.
Check the brake pedal height, brake pedal free play and brake pedal reserve distance.
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for LHD)>ADJUSTMENT
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for RHD)>ADJUSTMENT
If the brake pedal height is not within specification, confirm that there are no other malfunctions before adjusting the brake pedal height.
Brake inspection
Check that the disc brake pads of each wheel are installed correctly.
Check that the bleeder plug and union bolt is not loose, and that there are no damaged gaskets or brake fluid leaks, for each wheel cylinder.
Brake fluid leaks and air in brake line inspection
Check and take a note of the fluid level in the brake master cylinder reservoir assembly.
Repeatedly depress the brake pedal and confirm that the brake pedal feels normal (no air in the system, etc.).
Check if the brake fluid level in the brake master cylinder reservoir assembly has changed.
If the brake fluid level has decreased, check for leaks due to damaged brake lines or hoses, loose union nuts, damaged brake master cylinder sub-assembly seals, etc.
Bleeding air from brake system
Bleed air from the brake lines and brake actuator assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Chassis / Brake/EPB / Active Test.
| Tester Display | Measurement Item | Control Range | Restrict Condition | Diagnostic Note |
|---|---|---|---|---|
| Motor Relay | ABS motor relay | Relay OFF / ON | Vehicle condition: Vehicle stopped
|
Refer to on-vehicle inspection for the brake actuator* |
*: Click here BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS > BRAKE ACTUATOR > ON-VEHICLE INSPECTION
| Tester Display |
|---|
| Motor Relay |
Fully depress and hold the brake pedal.
Make sure that the brake pedal has travelled excessively before holding it depressed.
Operate the ABS motor relay using the Active Test and check if the brake pedal height changes when the pump motor is operating.
The brake pedal height does not change (the brake pedal travel remains excessive).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for RHD)>REMOVAL
Check that there are no brake fluid leaks and no indications of a malfunction in the brake master cylinder sub-assembly.
There are no brake fluid leaks and no indications of a malfunction in the brake master cylinder sub-assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER (for LHD)>DISASSEMBLY
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER (for RHD)>DISASSEMBLY
Inspect operation of the brake booster assembly.
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>ON-VEHICLE INSPECTION
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>ON-VEHICLE INSPECTION
The brake booster assembly is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL