Home › Engine / Hybrid System › M20A-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2021.02
RM33A0E _51 Engine / Hybrid System _098626 M20A-FKS ENGINE CONTROL _0466473 SFI SYSTEM J

M20A-FKS ENGINE CONTROL  SFI SYSTEM  Active Control Engine Mount System  


DESCRIPTION

A485001C01
1.083,4.177 1.354,4.177 1.354,4.177 2.24,3.438 true 1.333,4.51 1.604,4.51 1.604,4.51 2.49,3.771 true 5.615,3.823 5.323,3.823 5.323,3.823 4.604,2.573 true 0.906,4.115 1.219,4.313 0.313,0.198 10 false *1 1.156,4.427 1.469,4.625 0.313,0.198 10 false *2 5.656,3.75 5.969,3.948 0.313,0.198 10 false *3
*1 Vacuum Switching Valve (for Active Control Engine Mount System) *2 Front Engine Mounting Insulator
*3 Rear Engine Mounting Insulator - -


The active control engine mount system decreases engine vibration at a low engine speed using the vacuum switching valve (for active control engine mount system). The vacuum switching valve (for active control engine mount system) is controlled by a pulse signal transmitted to the vacuum switching valve (for active control engine mount system) from the ECM. The frequency of this pulse signal is matched to the engine speed to decrease engine vibration.

WIRING DIAGRAM

A450602E02
1.656,1.896 2.719,2.094 1.063,0.198 10 false EFI-MAIN NO. 1 0.5,1.281 1.563,1.479 1.063,0.198 10 false EFI-MAIN NO. 1 2.708,1.24 3.365,1.417 0.656,0.177 10 false EFI NO. 1 1.708,0.938 1.875,1.146 0.167,0.208 10 false 3 2.458,0.927 2.625,1.135 0.167,0.208 10 false 5 1.708,1.458 1.875,1.667 0.167,0.208 10 false 1 2.469,1.448 2.635,1.656 0.167,0.208 10 false 2 3.542,0.99 3.708,1.198 0.167,0.208 10 false 1 4.99,0.979 5.156,1.188 0.167,0.208 10 false 2 3.458,1.427 3.771,1.625 0.313,0.198 10 false C15 3.458,1.583 5.604,2.25 2.146,0.667 10 false Vacuum Switching Valve (for Active Control Engine Mount System) 5.354,1.094 5.802,1.417 0.448,0.323 10 false C57 5.365,3 5.677,3.198 0.313,0.198 10 false A24 5.75,0.969 6.24,1.188 0.49,0.219 10 false ACM 5.75,2.875 6.208,3.063 0.458,0.188 10 false MREL 5.406,0.896 5.604,1.104 0.198,0.208 10 false 44 5.396,2.813 5.563,3.021 0.167,0.208 10 false 15 5.354,3.688 5.667,3.885 0.313,0.198 10 false A24 5.417,3.5 5.583,3.708 0.167,0.208 10 false 10 5.74,3.698 6.052,3.896 0.313,0.198 10 false E1 6.125,4.156 6.552,4.375 0.427,0.219 10 false ECM 0.677,3.76 1.542,3.948 0.865,0.188 10 false Battery 0.594,2.271 1.656,2.469 1.063,0.198 10 false FL MAIN 3.708,0.99 3.969,1.271 0.26,0.281 10 false +B 4.604,0.99 5.021,1.198 0.417,0.208 10 false ACM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM))
A337501C52
0.552,1.188 0.896,1.438 0.344,0.25 1.083,1.802 1.5,1.385 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 0.604,1.229 0.917,1.427 0.313,0.198 10 false C15 0.865,1.813 1.177,2.01 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Vacuum Switching Valve (for Active Control Engine Mount System))


a.

Disconnect the vacuum switching valve (for active control engine mount system) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C15-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM) - EFI-MAIN NO. 1 RELAY)

2.INSPECT VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM)
a.

Inspect the vacuum switching valve (for active control engine mount system).

Click hereEngine / Hybrid System>M20A-FKS (ENGINE CONTROL)>VACUUM SWITCHING VALVE (for Engine Mounting)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM) - ECM)

NG

REPLACE VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM)

3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACTIVE CONTROL ENGINE MOUNT SYSTEM) - ECM)
a.

Disconnect the vacuum switching valve (for active control engine mount system) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C15-2 (ACM) - C57-44 (ACM) Always Below 1 Ω
C15-2 (ACM) or C57-44 (ACM) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK VACUUM HOSES

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK VACUUM HOSES
A403546C01
2.01,1.406 2.333,1.688 0.323,0.281 10 false *1 2.021,0.385 2.344,0.667 0.323,0.281 10 false *2 1.115,2.594 1.438,2.875 0.323,0.281 10 false *3 2.948,2.594 3.271,2.875 0.323,0.281 10 false *4 0.281,1.813 0.604,2.094 0.323,0.281 10 false *5 1.135,1.813 1.458,2.094 0.323,0.281 10 false *6
*1 Engine
*2 Vacuum Pump Assembly
*3 Front Engine Mounting Insulator
*4 Rear Engine Mounting Insulator
*5 ECM
*6 Vacuum Switching Valve (for Active Control Engine Mount System)


a.

Check the air and vacuum hoses for looseness, disconnection and blockage.

OK:

No looseness, disconnection or blockage.



Result:
Proceed to
OK
NG



OK

5.CHECK VACUUM

NG

REPAIR OR REPLACE VACUUM HOSES

5.CHECK VACUUM
A449650

a.

Disconnect the vacuum hose from the vacuum pump assembly.


b.

Start the engine.


c.

Check that the disconnected port located on the vacuum pump assembly applies suction to your finger.

OK:

Vacuum exists.



Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT ENGINE MOUNTING INSULATOR

NG

6.INSPECT FRONT ENGINE MOUNTING INSULATOR

Result:
Proceed to
OK
NG



OK

7.INSPECT REAR ENGINE MOUNTING INSULATOR

NG

7.INSPECT REAR ENGINE MOUNTING INSULATOR

Result:
Proceed to
OK
NG



OK

NG