Home › Drivetrain › P710 (HYBRID TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2017.09–2019.10
RM33C0E _52 Drivetrain _065428 P710 HYBRID TRANSMISSION / TRANSAXLE _0319558 TRANSMISSION CONTROL CABLE A

P710 HYBRID TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before adjusting the transmission control cable assembly, check that the shift lever position sensor and shift lever are in N.


a.
C377951N01
2.833,1.385 2.99,1.583 0.156,0.198 10 false N 2.583,2 2.75,2.177 0.167,0.177 10 false P

Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.


b.

Engage the 2 claws to install a new clip to the transmission control cable assembly.


c.
C377953C01
1.25,1.385 0.969,0.573 0.969,0.573 2.167,1.365 true 1.146,1.635 2.948,2.521 2.948,2.521 2.313,1.646 true 2.646,1.063 2.75,0.698 2.75,0.698 2.896,0.698 false 1.26,2.979 1.406,2.979 1.406,2.979 1.583,2.417 true 1.094,2.917 1.385,3.156 0.292,0.24 10 false *1 2.958,0.625 3.26,0.802 0.302,0.177 10 false *2 0.792,0.479 1.104,0.667 0.313,0.188 10 false *a 3,2.469 3.313,2.625 0.313,0.156 10 false *b
*1 Transmission Control Cable Assembly
*2 No. 1 Transmission Control Cable Bracket
*a Claw (A)
*b Claw (B)


Using a screwdriver, engage the 4 claws and install the transmission control cable assembly to the No. 1 transmission control cable bracket.

NOTICE:
·

Make sure that the claws (A) of the clip are securely engaged in the grooves of the bracket.

·

Make sure that the transmission control cable assembly is securely installed inside of the claws (B) of the clip.




d.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


e.

Connect the transmission control cable assembly to the inverter with converter assembly with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


f.

Connect the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


g.

Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 58861B 3.INSTALL NO. 1 CONSOLE BOX DUCT

a.

Install the No. 1 console box duct.


Hide 4.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY

Hide 58152A 5.INSTALL FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

a.

Install the front lower No. 1 floor heat insulator to the vehicle body with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 17410 6.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 7.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 12601B 8.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17750A 9.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 10.INSTALL COOL AIR INTAKE DUCT SEAL