Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2017.09–2019.02
RM33C0E _58 Vehicle Interior _065456 THEFT DETERRENT / KEYLESS ENTRY _0330906 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (READY)  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P and the brake pedal is depressed, the hybrid control system can be started by pressing the power switch. If the steering is unlocked, the hybrid control system can also be started by pressing the power switch with the shift lever in P and the brake pedal depressed.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to ON (READY)
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Shift P Signal

·

IG Relay Monitor (Inside)

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Starter Request Signal

·

Power Supply Condition


Smart Key
·

Immobiliser

·

Engine Start Request

·

L Code Check



WIRING DIAGRAM

B494140E01
0.094,1.76 0.958,2.208 0.865,0.448 10 false from Auxiliary Battery 1.531,1.917 2.104,2.208 0.573,0.292 10 false STOP 2.031,1.656 2.417,1.917 0.385,0.26 10 false 7 2.01,2.052 2.396,2.313 0.385,0.26 10 false 2 2.177,1.781 2.563,2.042 0.385,0.26 10 false B 2.583,2 2.844,2.24 0.26,0.24 10 false IC 2.958,1.896 3.344,2.156 0.385,0.26 10 false L 3.146,1.885 3.531,2.146 0.385,0.26 10 false 3 1.656,0.719 2.042,0.979 0.385,0.26 10 false K27 1.646,0.885 3.771,1.271 2.125,0.385 10 false Shift Lock Control Unit Assembly 2.865,0.365 3.25,0.625 0.385,0.26 10 false P2 3.146,0.271 3.531,0.531 0.385,0.26 10 false 3 5.219,0.365 5.604,0.625 0.385,0.26 10 false K62 5.26,0.177 5.646,0.438 0.385,0.26 10 false 22 2.031,2.583 2.927,2.813 0.896,0.229 10 false A37 2.031,2.74 3.146,3.198 1.115,0.458 10 false Stop Light Switch Assembly 3.229,3.906 4.458,4.167 1.229,0.26 10 false A40 5.344,5.938 6.875,6.385 1.531,0.448 10 false Certification ECU (Smart Key ECU Assembly) 0.292,5.938 1.677,6.323 1.385,0.385 10 false Hybrid Vehicle Control ECU Assembly 5.906,4.469 6.479,4.76 0.573,0.292 10 false +B 1.104,3.604 1.677,3.896 0.573,0.292 10 false STP 1.083,4.854 1.656,5.146 0.573,0.292 10 false ST2 5.26,1.813 5.646,2.073 0.385,0.26 10 false 25 5.25,2 5.635,2.26 0.385,0.26 10 false R8 5.26,4.771 5.646,5.031 0.385,0.26 10 false 27 1.448,3.573 1.833,3.833 0.385,0.26 10 false A28 1.458,4.948 1.844,5.208 0.385,0.26 10 false K69 1.542,4.75 1.927,5.01 0.385,0.26 10 false 9 1.479,3.385 1.865,3.646 0.385,0.26 10 false 15 5.573,0.365 5.958,0.625 0.385,0.26 10 false P 6.406,2.115 6.667,2.354 0.26,0.24 10 false IC 6.406,5.094 6.667,5.333 0.26,0.24 10 false IC 5.219,4.958 5.604,5.219 0.385,0.26 10 false K62 2.156,2.146 2.542,2.406 0.385,0.26 10 false GND 3.865,3.552 4.438,3.844 0.573,0.292 10 false STP2 5.573,1.896 6.146,2.188 0.573,0.292 10 false STP1 5.563,4.844 6.135,5.135 0.573,0.292 10 false ST2 3.635,3.469 4.208,3.76 0.573,0.292 10 false 37 3.219,4.063 5.281,4.479 2.063,0.417 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the smart entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.



PROCEDURE

1.CHECK POWER SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the power switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes : Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) or on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

C

D

2.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

7.CHECK STOP LIGHT SWITCH ASSEMBLY
3.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position P OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
Use this item to determine whether the shift lever position switch (P) is malfunctioning.
Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 223 1
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

9.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
4.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Hybrid control system start request signal status OFF or ON OFF: The power switch is not pressed
ON: With the shift lever in P and the brake pedal depressed, the power switch is pressed and held
·

When the hybrid control system cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the power switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the power switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the power switch.


OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)

NG

10.CHECK STEERING LOCK FUNCTION
5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU ASSEMBLY)
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K69 hybrid vehicle control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-27 (ST2) - K69-9 (ST2) Always Below 1 Ω
K62-27 (ST2) or K69-9 (ST2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the K62 certification ECU (smart key ECU assembly) connector.


b.

Connect the K69 hybrid vehicle control ECU assembly connector.


c.
B424427C97
1.542,0.083 1.958,0.333 0.417,0.25 1.042,1.927 1.229,1.927 1.229,1.927 1.229,1.115 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.625,0.115 1.938,0.271 0.313,0.156 10 false K62 0.771,1.865 1.271,2.104 0.5,0.24 10 false ST2
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K62-27 (ST2) - Body ground With the brake pedal depressed, the power switch is pressed and held → After approx. 3 sec. has elapsed, the power switch is released 8.5 V or higher → 1.0 V or less



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A37 stop light switch assembly connector.


b.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the A28 hybrid vehicle control ECU assembly connector.


d.

Disconnect the A40 skid control ECU (brake booster with master cylinder assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R8-25 (STP1) - A37-3 (L) Always Below 1 Ω
R8-25 (STP1) or A37-3 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.
B424427C98
1.542,0.083 1.958,0.333 0.417,0.25 2.156,1.938 1.938,1.938 1.938,1.938 1.823,1.125 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.625,0.125 2.01,0.333 0.385,0.208 10 false K62 2.188,1.865 2.688,2.104 0.5,0.24 10 false P
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K62-22 (P) - Body ground Shift lever in P → Shift lever not in P 9 V or higher → 2.76 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
10.CHECK STEERING LOCK FUNCTION
a.

Check that the steering unlocks when the power switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

11.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)

NG

11.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the power switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the K27 shift lock control unit assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K62-22 (P) - K27-3 (P2) Always Below 1 Ω
K62-22 (P) or K27-3 (P2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR