This DTC is stored when the combination meter assembly detects an open in a front turn signal light circuit or rear turn signal light circuit.
If there is an open in a front turn signal light circuit or rear turn signal light circuit, the turn signal lights on the side with the open circuit will blink faster than usual.
If there is an open in a side turn signal light circuit, DTC B150718 will not be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B150718 | Turn Signal Light Circuit Current Below Threshold | Diagnosis Condition:
Auxiliary battery voltage is 10 V or more Malfunction Status: ·
Open in front turn signal light circuit ·
Open in rear turn signal light circuit |
·
Headlight ECU sub-assembly*4 ·
Head light unit assembly*4 ·
Headlight lens*1 ·
Front turn signal light socket*5 ·
Rear combination light assembly*2 ·
Rear combination light cord*2 ·
Rear combination light socket and wire*3 ·
Harness or connector ·
Combination meter assembly |
DTC stored | - |
*1: for LED Type Turn Signal Light
*2: for LED Type Back-up Light
*3: for Bulb Type Back-up Light
*4: w/ Automatic Headlight Beam Level Control System
*5: w/o Automatic Headlight Beam Level Control System
LH SIDE
RH SIDE
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Inspect the turn signal light bulbs and sockets before performing the following procedure.
Inspect the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| Front turn signal light LH does not blink | A |
| Rear turn signal light LH does not blink | B |
| Front turn signal light RH does not blink | C |
| Rear turn signal light RH does not blink | D |
A
B
C
D
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Automatic Headlight Beam Level Control System | A |
| w/o Automatic Headlight Beam Level Control System | B |
A
B
Disconnect the A78 headlight assembly LH connector.
Disconnect the K20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A78-11 (TNS) - K20-11 (LL) | Always | Below 1 Ω |
| A78-12 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Headlight ECU Sub-assembly LH) |
- | - |
Remove the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-9 (TURN+) - A78-11 (TNS) | Always | Below 1 Ω |
| B-13 (TURN-) - A78-12 (GND) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove each headlight ECU sub-assembly, interchange the headlight unit assembly LH with RH and connect the connectors.
for LED Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
for Bulb Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Check that the front turn signal light operates normally.
Front turn signal light blinks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Turn Signal Light | A |
| for Bulb Type Turn Signal Light | B |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Remove the headlight lens LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Inspect the headlight lens LH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Disconnect the A76 headlight assembly LH connector.
Disconnect the K20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A76-1 (B) - K20-11 (LL) | Always | Below 1 Ω |
| A76-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the front turn signal light socket LH with RH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Check that the front turn signal light operates normally.
Front turn signal light blinks.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
NG
Disconnect the W13 rear combination light assembly LH connector.
Disconnect the K20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W13-3 (B) - K20-10 (TRNL) | Always | Below 1 Ω |
| W13-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Back-up Light | A |
| for Bulb Type Back-up Light | B |
A
B
Interchange the rear combination light cord LH with RH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY
Check that the rear turn signal light operates normally.
Rear turn signal light blinks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear combination light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL
Inspect the rear combination light assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the rear combination light socket and wire LH with RH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY
Check that the rear turn signal light operates normally.
Rear turn signal light blinks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Automatic Headlight Beam Level Control System | A |
| w/o Automatic Headlight Beam Level Control System | B |
A
B
Disconnect the A79 headlight assembly RH connector.
Disconnect the K20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A79-11 (TNS) - K20-7 (LR) | Always | Below 1 Ω |
| A79-12 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Headlight ECU Sub-assembly RH) |
- | - |
Remove the headlight ECU sub-assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-9 (TURN+) - A79-11 (TNS) | Always | Below 1 Ω |
| B-13 (TURN-) - A79-12 (GND) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove each headlight ECU sub-assembly, interchange the headlight unit assembly RH with LH and connect the connectors.
for LED Type Turn Signal: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
for Bulb Type Turn Signal Light: Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Check that the front turn signal light operates normally.
Front turn signal light blinks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Turn Signal Light | A |
| for Bulb Type Turn Signal Light | B |
A
B
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Remove the headlight lens RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Inspect the headlight lens RH.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
NG
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Type Turn Signal Light)>DISASSEMBLY
Disconnect the A75 headlight assembly RH connector.
Disconnect the K20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A75-1 (B) - K20-7 (LR) | Always | Below 1 Ω |
| A75-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the front turn signal light socket RH with LH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
Check that the front turn signal light operates normally.
Front turn signal light blinks.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY
NG
Disconnect the W12 rear combination light assembly RH connector.
Disconnect the K20 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W12-3 (B) - K20-13 (TRNR) | Always | Below 1 Ω |
| W12-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LED Type Back-up Light | A |
| for Bulb Type Back-up Light | B |
A
B
Interchange the rear combination light cord RH with LH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY
Check that the rear turn signal light operates normally.
Rear turn signal light blinks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear combination light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>REMOVAL
Inspect the rear combination light assembly RH.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Interchange the rear combination light socket and wire RH with LH and connect the connectors.
Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY
Check that the rear turn signal light operates normally.
Rear turn signal light blinks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG