Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0095  Intake Air Temperature Sensor 2 Circuit  P0097  Intake Air Temperature Sensor 2 Circuit Low  P0098  Intake Air Temperature Sensor 2 Circuit High  


DESCRIPTION

The Intake Air Temperature (IAT) sensor (after turbocharged), built into the intake pipe, senses the turbocharged air temperature. A thermistor built in the sensor changes the resistance value according to the IAT. The lower the IAT, the greater the thermistor resistance value, and the higher the IAT, the lower the thermistor resistance value (see Fig. 1).

The IAT sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the IAT sensor from terminal THIA via a resistor R. The resistor R and IAT sensor are connected in series. When the resistance value of the IAT sensor changes in accordance with changes in the IAT, the voltage at terminal THIA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability during cold engine operation.

DTC No. Proceed to DTC Detection Condition Trouble Area
P0095 Step 1 Open or short in intake air temperature sensor (after turbocharged) circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in intake air temperature sensor (after turbocharged) circuit

·

Intake air temperature sensor (after turbocharged)

·

ECM


P0097 Step 4 Short in intake air temperature sensor (after turbocharged) circuit for 0.5 seconds
(1 trip detection logic)
·

Short in intake air temperature sensor (after turbocharged) circuit

·

Intake air temperature sensor (after turbocharged)

·

ECM


P0098 Step2 Open in intake air temperature sensor (after turbocharged) circuit for 0.5 seconds
(1 trip detection logic)
·

Open in intake air temperature sensor (after turbocharged) circuit

·

Intake air temperature sensor (after turbocharged)

·

ECM



HINT:

When any of DTCs are set, check the IAT by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
190°C (374°F) Short circuit


WIRING DIAGRAM

A199002E38
5.208,1.573 5.438,1.75 0.229,0.177 10 false 28 5.167,1.771 5.479,1.979 0.313,0.208 10 false B59 5.219,0.958 5.448,1.135 0.229,0.177 10 false 20 5.51,1.667 5.885,1.865 0.375,0.198 10 false E2 5.5,1.052 5.865,1.229 0.365,0.177 10 false THIA 5.167,1.156 5.5,1.354 0.333,0.198 10 false B59 0.594,2.385 0.917,2.563 0.323,0.177 10 false B13 2.438,1.646 2.573,1.844 0.135,0.198 10 false 1 2.427,1.042 2.583,1.219 0.156,0.177 10 false 2 5.969,2.688 6.365,2.833 0.396,0.146 10 false ECM 0.604,2.531 2.542,2.75 1.938,0.219 10 false Intake Air Temperature Sensor 6.198,0.708 6.448,0.875 0.25,0.167 10 false 5 V 6.125,0.948 6.271,1.104 0.146,0.156 10 false R

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).


e.

Read the value.

OK:

Same value as the actual intake air temperature.


Result:
Result Proceed to
-40°C (-40°F) A
190°C (374°F) B
OK (same as actual intake air temperature) C


HINT:
·

If there is an open circuit, the intelligent tester indicates -40°C (-40°F).

·

If there is a short circuit, the intelligent tester indicates 190°C (374°F).





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A224409E02
0.698,3.531 1.115,3.771 0.417,0.24 0.792,0.479 1.01,0.677 0.219,0.198 10 false *1 0.313,2.333 0.49,2.479 0.177,0.146 10 false *3 0.792,3.573 1.135,3.781 0.344,0.208 10 false B13 2.406,1.167 2.771,1.333 0.365,0.167 10 false THIA 2.656,0.302 2.906,0.51 0.25,0.208 10 false *2 2.406,1.521 2.677,1.708 0.271,0.188 10 false E2

Disconnect the intake air temperature sensor connector.


b.

Connect terminals 1 and 2 of the intake air temperature sensor harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).


g.

Read the value.

Standard:

190°C (374°F)


Text in Illustration
*1 Intake Air Temperature Sensor
*2 ECM
*3 Front view of wire harness connector
(to Intake Air Temperature Sensor Connector)


h.

Reconnect the intake air temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)
3.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)
a.
A153588E24
0.542,2.74 0.948,3.01 0.406,0.271 0.854,3.427 0.531,3.865 true 0.958,3.5 1.021,3.865 true 0.792,0.573 1.031,0.76 0.24,0.188 10 false *1 2.635,0.292 2.896,0.51 0.26,0.219 10 false *2 0.198,2.531 0.385,2.708 0.188,0.177 10 false *3 0.615,2.792 0.927,2.969 0.313,0.177 10 false B59 2.406,1.167 2.802,1.344 0.396,0.177 10 false THIA 0.271,3.875 0.656,4.052 0.385,0.177 10 false THIA 2.406,1.51 2.729,1.698 0.323,0.188 10 false E2 0.979,3.875 1.25,4.052 0.271,0.177 10 false E2

Disconnect the intake air temperature sensor connector.


b.

Connect terminals THIA and E2 of the ECM connector.

HINT:

Before checking, do a visual and contact pressure check for the ECM connector.



c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).


g.

Read the value.

Standard:

190°C (374°F)


Text in Illustration
*1 Intake Air Temperature Sensor
*2 ECM
*3 Component with harness connected
(ECM)


h.

Reconnect the intake air temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR)

NG

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A076591E35
0.729,0.292 0.906,0.479 0.177,0.188 10 false *1 2.698,0.24 2.917,0.427 0.219,0.188 10 false *2 2.448,0.906 2.854,1.104 0.406,0.198 10 false THIA 2.448,1.292 2.688,1.49 0.24,0.198 10 false E2

Disconnect the intake air temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).


f.

Read the value.

Standard:

-40°C (-40°F)


Text in Illustration
*1 Intake Air Temperature Sensor
*2 ECM


g.

Reconnect the intake air temperature sensor connector.


Result:
Proceed to
OK
NG



OK

NG

5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)
5.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)
a.
A153589E22
0.531,2.99 0.938,3.208 0.406,0.219 0.979,4.042 1.198,4.302 true 0.865,3.948 1.302,3.885 true 0.844,0.542 1.156,0.74 0.313,0.198 10 false *1 2.625,0.24 2.938,0.438 0.313,0.198 10 false *2 2.417,1.177 2.813,1.375 0.396,0.198 10 false THIA 2.417,1.531 2.813,1.729 0.396,0.198 10 false E2 0.198,2.333 0.51,2.531 0.313,0.198 10 false *3 1.354,3.802 1.74,4.021 0.385,0.219 10 false THIA 1.25,4.323 1.5,4.531 0.25,0.208 10 false E2 0.615,3.01 0.927,3.198 0.313,0.188 10 false B59

Disconnect the ECM connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).


f.

Read the value.

Standard:

-40°C (-40°F)


Text in Illustration
*1 Intake Air Temperature Sensor
*2 ECM
*3 Rear view of wire harness connector
(to ECM)


g.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR)

NG