Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0340  Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet and MRE element.

The camshaft drive gear has 5 teeth on its inner circumference. When the camshaft gear rotates, air gap changes between the protrusion on the gear and the pickup coil. The change affects the magnetic field and results in change in the resistance of the MRE element. The NE signal plate has 32 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 32 signals for every revolution. The ECM detects the camshaft angle based on the G signal, and detects the crankshaft angle based on the NE signal.

DTC No. DTC Detection Condition Trouble Area
P0340 STA ON:
No camshaft position sensor signal to ECM while cranking for 4 seconds or more
STA OFF:
No camshaft position sensor signal to ECM with engine speed 650 to 3000 rpm 20 times or more
(1 trip detection logic)
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft (camshaft drive gear)

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CAMSHAFT POSITION SENSOR
a.

While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

A427627E03
0.885,0.729 1.281,0.979 0.396,0.25 1.417,0.729 1.813,0.979 0.396,0.25 0.646,1.969 0.854,1.396 true 1.427,2.063 0.854,1.448 true 2.135,2.063 1.698,1.448 true 2.135,0.927 1.698,1.396 true 0.219,0.24 0.531,0.438 0.313,0.198 10 false *1 0.958,0.781 1.271,0.979 0.313,0.198 10 false B59 1.5,0.771 1.813,0.969 0.313,0.198 10 false B60 0.354,2 0.979,2.198 0.625,0.198 10 false 27 (NE+) 1.208,2.094 1.833,2.292 0.625,0.198 10 false 34 (NE-) 2.01,2.104 2.635,2.302 0.625,0.198 10 false 31 (G-) 2.188,0.781 2.813,0.979 0.625,0.198 10 false 23 (G+) 4.083,0.25 4.396,0.448 0.313,0.198 10 false *2 4.125,0.896 4.375,1.083 0.25,0.188 10 false G+ 4.115,1.51 4.365,1.698 0.25,0.188 10 false NE 6.042,0.708 7.135,0.958 1.094,0.25 10 false 5 V/DIV. 4.823,2.167 6.417,2.375 1.594,0.208 10 false 20 msec./DIV.

Text in Illustration
*1 Component with harness connected
(ECM)
*2 G+ and NE Signal Waveforms

Standard:
Tester Connection Condition Specified Condition
B59-27 (NE+) - B59-34 (NE-) Engine idling Correct waveform appears as shown
B60-23 (G+) - B60-31 (G-) Engine idling Correct waveform appears as shown



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT ECM (VCG VOLTAGE)
2.INSPECT ECM (VCG VOLTAGE)
a.
A224395E29
1.188,0.198 1.625,0.448 0.438,0.25 1.177,1.521 1.563,1.031 true 1.99,1.531 1.615,0.938 true 0.083,0.083 0.302,0.292 0.219,0.208 10 false *1 1,1.552 1.49,1.76 0.49,0.208 10 false 31(G- ) 1.792,1.563 2.438,1.802 0.646,0.24 10 false 22 (VCG) 1.281,0.24 1.594,0.417 0.313,0.177 10 false B60

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B60-22 (VCG) - B60-31 (G-) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*1 Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
k2-1 (G1) - B60-23 (G+) Always Below 1 Ω
k2-2 (G-) - B60-31 (G-) Always Below 1 Ω
k2-3 (VG) - B60-22 (VCG) Always Below 1 Ω
k2-1 (G1) or B60-23 (G+) - Body ground Always 10 kΩ or higher
k2-2 (G-) or B60-31 (G-) - Body ground Always 10 kΩ or higher
k2-3 (VG) or B60-22 (VCG) - Body ground Always 10 kΩ or higher



d.

Reconnect the camshaft position sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.

Check the camshaft position sensor installation condition.


A369509E04
0.51,1.698 0.813,1.896 0.302,0.198 10 false OK 2.656,1.781 2.948,1.979 0.292,0.198 10 false NG 1.667,1.552 2.344,1.75 0.677,0.198 10 false Clearance

OK:

The camshaft position sensor is installed properly.


Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT (CAMSHAFT DRIVE GEAR)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT CAMSHAFT (CAMSHAFT DRIVE GEAR)
a.

Check the teeth of the camshaft drive gear.

OK:

The teeth of the camshaft drive gear do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE CAMSHAFT POSITION SENSOR

NG

REPLACE CAMSHAFT (CAMSHAFT DRIVE GEAR)

6.REPLACE CAMSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTC.


Result:
Result Proceed to
P0340 A
No output B



A

B

END