Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0488  Exhaust Gas Recirculation Throttle Position Control Range / Performance  


DESCRIPTION

The throttle control motor opens and closes the throttle valve according to a VTAR-cycle (signal) from the ECM.

DTC No. DTC Detection Condition Trouble Area
P0488 Condition (a) or (b) continues for more than 1 second
(1 trip detection logic)
(a) Battery voltage is 10 V or more
·

Throttle motor's activation duty is out of the normal range (Activation duty: 10 to 90)


(b) Open, short or stuck in throttle sensor
·

Open or short in throttle control motor circuit

·

Throttle control motor (built into diesel throttle body assembly)

·

ECM



WIRING DIAGRAM

A398544E01
0.635,1.146 0.917,1.333 0.281,0.188 10 false P/I 0.344,1.698 1.208,1.896 0.865,0.198 10 false R/B NO. 2-B 1.583,1.125 2.25,1.313 0.667,0.188 10 false EFI-MAIN 3.781,1.125 4.448,1.313 0.667,0.188 10 false EFI NO. 3 1.271,0.969 1.552,1.156 0.281,0.188 10 false 2E 3.271,0.958 3.552,1.146 0.281,0.188 10 false 2D 3.281,1.427 3.563,1.615 0.281,0.188 10 false 2D 1.5,1.917 1.781,2.104 0.281,0.188 10 false 2D 1.313,0.781 1.51,0.99 0.198,0.208 10 false 1 3.323,0.76 3.521,0.969 0.198,0.208 10 false 4 3.333,1.219 3.531,1.427 0.198,0.208 10 false 3 1.333,1.906 1.531,2.115 0.198,0.208 10 false 2 2.563,1.781 2.875,1.969 0.313,0.188 10 false EFI 1.885,2.146 3.406,2.354 1.521,0.208 10 false No. 2 Integration Relay 0.365,2.792 1.031,2.979 0.667,0.188 10 false FL MAIN 0.99,3.479 1.656,3.667 0.667,0.188 10 false Battery 4.615,0.969 4.99,1.167 0.375,0.198 10 false VCR 4.615,1.417 4.99,1.615 0.375,0.198 10 false E2R 5.146,1.177 5.573,1.375 0.427,0.198 10 false VTAR 6.01,1.198 6.313,1.385 0.302,0.188 10 false B60 6.021,3.167 6.323,3.354 0.302,0.188 10 false A54 6.552,4.271 6.979,4.469 0.427,0.198 10 false ECM 6.438,3.156 6.865,3.354 0.427,0.198 10 false MREL 6.438,1.188 6.865,1.385 0.427,0.198 10 false LUSL 4.531,1.719 4.906,1.917 0.375,0.198 10 false B45 4.521,1.896 6.333,2.271 1.813,0.375 10 false Throttle Control Motor (built into Throttle Body Assembly) 4.406,0.865 4.604,1.073 0.198,0.208 10 false 2 4.406,1.313 4.604,1.521 0.198,0.208 10 false 3 6.073,0.979 6.271,1.188 0.198,0.208 10 false 4 6.063,2.958 6.271,3.146 0.208,0.188 10 false 13 5.625,1.063 5.823,1.271 0.198,0.208 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK THROTTLE CONTROL MOTOR (+B VOLTAGE)
a.
A153612E06
1.49,1.083 1.927,1.354 0.438,0.271 1.094,2.719 1.396,2.344 true 1.635,2.781 1.719,2.375 true 2.385,2.708 2,2.375 true 0.271,0.333 0.583,0.531 0.313,0.198 10 false *1 1.583,1.135 1.917,1.333 0.333,0.198 10 false B45 0.75,2.74 1.156,2.948 0.406,0.208 10 false VTAR 1.479,2.823 1.885,3.031 0.406,0.208 10 false VCR 2.281,2.719 2.688,2.927 0.406,0.208 10 false E2R

Disconnect the throttle control motor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B45-2 (VCR) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*1 Front view of wire harness connector
(to Throttle Control Motor)


d.

Reconnect the throttle control motor connector.


Result:
Proceed to
OK
NG



OK

2.CHECK THROTTLE CONTROL MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE CIRCUIT)

2.CHECK THROTTLE CONTROL MOTOR

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)

NG

REPLACE DIESEL THROTTLE BODY ASSEMBLY (THROTTLE CONTROL MOTOR)

3.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)
a.

Disconnect the throttle control motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B45-1 (VTAR) - B60-4 (LUSL) Always Below 1 Ω
B45-3 (E2R) - Body ground Always Below 1 Ω
B45-1 (VTAR) or B60-4 (LUSL) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle control motor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR