Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0544  Exhaust GAS Temperature Sensor Circuit (Bank 1 Sensor 1)  P0545  Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1)  P0546  Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

A164232E04
1.031,1.19 1.423,1.541 0.392,0.351 10 ECM 0.271,2.423 0.795,2.753 0.524,0.33 10 Exhaust Gas 2.481,0.041 4.151,0.359 1.67,0.318 10 Exhaust Gas Temperature Sensor (Bank 1 Sensor 1) 3.56,1.239 5.212,1.569 1.653,0.33 10 Exhaust Gas Temperature Sensor (Bank 1 Sensor 2) 2.449,0.111 2.33,0.111 false 2.33,0.111 2.045,2.061 false 3.538,1.316 3.451,1.316 false 3.451,1.316 3.202,2.348 false 4.418,0.419 6.629,0.629 2.211,0.21 10 Exhaust Gas Temperature Sensor: 0.511,3.25 2.63,3.432 2.119,0.181 10 Property of Output Voltage: 1.742,3.586 4.356,3.881 2.615,0.295 10 Exhaust Gas Temperature Sensor °C (°F) 2.319,5.477 5.183,5.633 2.865,0.156 10 Exhaust Gas Temperature Sensor Voltage (V) 2.204,4.763 3.805,4.933 1.601,0.17 10 P0545 or P2032 detected 4.054,4.314 5.654,4.609 1.601,0.295 10 P0546 or P2033 detected 2.162,4.833 2.022,4.833 false 2.022,4.833 1.838,4.648 false 5.665,4.398 5.819,4.398 false 5.819,4.398 6.085,4.132 false 3.059,3.095 4.632,3.404 1.573,0.309 10 DPF Catalytic Converter 3.031,3.165 2.798,3.165 false 2.798,3.165 2.376,2.733 false 0.943,3.768 1.796,3.933 0.853,0.166 10 1000 (1832) 1.013,3.931 1.755,4.097 0.742,0.166 10 960 (1760) 1.013,4.141 1.755,4.307 0.742,0.166 10 760 (1400) 1.013,4.389 1.755,4.554 0.742,0.166 10 560 (1040) 1.088,4.627 1.714,4.793 0.626,0.166 10 360 (680) 1.088,4.884 1.714,5.049 0.626,0.166 10 160 (320) 1.144,5.136 1.715,5.302 0.571,0.166 10 -40 (-40) 1.687,5.259 1.789,5.424 0.102,0.166 10 0 1.832,5.259 2.052,5.424 0.22,0.166 10 0.2 2.078,5.259 2.297,5.424 0.22,0.166 10 0.5 2.526,5.259 2.746,5.424 0.22,0.166 10 1.0 2.971,5.259 3.191,5.424 0.22,0.166 10 1.5 3.409,5.259 3.628,5.424 0.22,0.166 10 2.0 3.85,5.259 4.07,5.424 0.22,0.166 10 2.5 4.295,5.259 4.515,5.424 0.22,0.166 10 3.0 4.747,5.259 4.966,5.424 0.22,0.166 10 3.5 5.188,5.259 5.408,5.424 0.22,0.166 10 4.0 5.626,5.259 5.846,5.424 0.22,0.166 10 4.5 5.93,5.259 6.22,5.424 0.289,0.166 10 4.95 6.295,5.259 6.532,5.424 0.237,0.166 10 5.0

The exhaust gas temperature sensors are installed in front of and behind the DPF* catalytic converter to sense the exhaust gas temperature.

A thermistor built into the sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature becomes, the greater the thermistor resistance value becomes. The higher the exhaust gas temperature becomes, the lower the thermistor resistance value becomes.

The exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the exhaust gas temperature sensor from terminals THC1 (bank 1 sensor 1) and THCO (bank 1 sensor 2) via resistor R.

The resistor R and the exhaust gas temperature sensor are connected in series. When the resistance value of the exhaust gas temperature sensor changes in accordance with changes in the exhaust gas temperature, the voltage at terminals THC1 (bank 1 sensor 1) and THCO (bank 1 sensor 2) also changes. Based on these signals, when DPF catalyst regeneration is needed, the ECM operates the injector to obtain target upstream temperature of the DPF catalytic converter as monitored through sensor 1. In addition, the ECM monitors the rate of DPF catalytic converter temperature increase using sensor 2.

*: Diesel Particulate Filter

DTC No. DTC Detection Condition Trouble Area
P0544 All of the following conditions are met:
(1 trip detection logic)
(a) Engine has been running for 30 minutes or more.
(b) Engine coolant temperature is 70°C (158°F) or higher.
(c) Injection volume is 40 mm3/st or more.
(d) Sensor 1 output is less than 0.2 V or more than 4.95 V for 8 seconds or more.
·

Open or short in exhaust gas temperature sensor (bank 1 sensor 1) circuit

·

Exhaust gas temperature sensor (bank 1 sensor 1)

·

ECM


P0545 All of the following conditions are met:
(1 trip detection logic)
(a) Engine has been running for 30 minutes or more.
(b) Engine coolant temperature is 70°C (158°F) or higher.
(c) Injection volume is 40 mm3/st or more.
(d) Sensor 1 output is less than 0.2 V for 8 seconds or more.
·

Open or short in exhaust gas temperature sensor (bank 1 sensor 1) circuit

·

Exhaust gas temperature sensor (bank 1 sensor 1)

·

ECM


P0546 All of the following conditions are met:
(1 trip detection logic)
(a) Engine has been running for 30 minutes or more.
(b) Engine coolant temperature is 70°C (158°F) or higher.
(c) Injection volume is 40 mm3/st or more.
(d) Sensor 1 output is more than 4.95 V for 8 seconds or more.
·

Open or short in exhaust gas temperature sensor (bank 1 sensor 1) circuit

·

Exhaust gas temperature sensor (bank 1 sensor 1)

·

ECM



HINT:
·

Sensor 1 represents a sensor located upstream on the DPF catalytic converter.

·

Sensor 2 represents a sensor located downstream on the DPF catalytic converter.

·

After confirming DTC P0544, P0545 and P0546 check the upstream and downstream exhaust gas temperature by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Exhaust Temperature B1S1 and Exhaust Temperature B1S2.

Result
Condition Exhaust Gas Temperature Exhaust Gas Temperature Sensor Condition
Idling after warm-up Constant at 50 to 700°C (122 to 1292°F) Normal
0°C (32°F) Open circuit
1000°C (1832°F) Short circuit



WIRING DIAGRAM

A199002E42
5.208,1.573 5.448,1.74 0.24,0.167 10 false 28 5.167,1.771 5.458,1.969 0.292,0.198 10 false B59 5.25,0.948 5.396,1.125 0.146,0.177 10 false 2 2.146,1.646 2.375,1.844 0.229,0.198 10 false E2 1.979,1.042 2.385,1.229 0.406,0.188 10 false THC1 5.521,1.656 5.833,1.823 0.313,0.167 10 false E2 5.51,1.063 5.917,1.229 0.406,0.167 10 false THCI 5.167,1.156 5.479,1.344 0.313,0.188 10 false B60 0.604,2.333 0.927,2.521 0.323,0.188 10 false A44 2.427,1.646 2.573,1.833 0.146,0.188 10 false 2 2.427,1.031 2.573,1.229 0.146,0.198 10 false 1 5.99,2.719 6.427,2.906 0.438,0.188 10 false ECM 0.594,2.51 2.698,2.875 2.104,0.365 10 false Exhaust Gas Temperature Sensor (Bank 1 Sensor 1) 6.188,0.688 6.458,0.875 0.271,0.188 10 false 5 V 6.146,0.938 6.323,1.115 0.177,0.177 10 false R

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (EXHAUST GAS TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S1.


e.

Read the value displayed on the tester.

Standard:

Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result:
Result Proceed to
0°C (32°F) (After warming up the engine) A
1000°C (1832°F) B
Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after maintaining the engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C


HINT:
·

If there is a open circuit, the intelligent tester will indicate 0°C (32°F).

·

If there is an short circuit, the intelligent tester will indicate 1000°C (1832°F).





A

2.READ VALUE USING INTELLIGENT TESTER (OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (SHORT IN WIRE HARNESS)

C

2.READ VALUE USING INTELLIGENT TESTER (OPEN IN WIRE HARNESS)
a.
A227219E03
0.698,3.594 1.104,3.844 0.406,0.25 0.771,3.646 1.094,3.833 0.323,0.188 10 false A44 2.344,1 2.771,1.177 0.427,0.177 10 false THCI 2.344,1.333 2.615,1.531 0.271,0.198 10 false E2 0.646,0.479 0.844,0.667 0.198,0.188 10 false *1 1.708,3.135 1.875,3.302 0.167,0.167 10 false *3 2.594,1.771 2.823,1.979 0.229,0.208 10 false *2

Disconnect the exhaust gas temperature sensor (bank1 sensor 1) connector.


b.

Connect terminals 1 and 2 of the exhaust gas temperature sensor wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S1.


g.

Read the value.

Standard:

1000°C (1832°F)


Text in Illustration
*1 Exhaust Gas Temperature Sensor (bank 1 sensor 1)
*2 ECM
*3 Front view of wire harness connector
(to Exhaust Gas Temperature Sensor (bank 1 sensor 1))


h.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPLACE EXHAUST GAS TEMPERATURE SENSOR (BANK 1 SENSOR 1)

NG

3.READ VALUE USING INTELLIGENT TESTER (OPEN IN ECM)
3.READ VALUE USING INTELLIGENT TESTER (OPEN IN ECM)
a.
A427721E01
0.563,2.604 0.958,2.833 0.396,0.229 1.229,2.604 1.625,2.833 0.396,0.229 0.875,3.906 0.99,3.458 true 1.781,3.938 1.615,3.208 true 0.719,0.375 1.031,0.573 0.313,0.198 10 false *1 2.646,0.344 2.958,0.542 0.313,0.198 10 false *2 2.438,1.177 2.844,1.354 0.406,0.177 10 false THCI 2.417,1.531 2.677,1.708 0.26,0.177 10 false E2 0.635,2.646 0.948,2.844 0.313,0.198 10 false B59 1.323,2.635 1.635,2.833 0.313,0.198 10 false B60 0.719,3.948 1.031,4.146 0.313,0.198 10 false E2 1.667,3.948 2.052,4.146 0.385,0.198 10 false THCI 0.188,2.25 0.5,2.448 0.313,0.198 10 false *3

Disconnect the exhaust gas temperature sensor (bank1 sensor 1) connector.


b.

Connect terminals THC1 and E2 of the ECM connectors.

HINT:

Before checking, do a visual and contact pressure check on the ECM connector.



c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S1.


g.

Read the value.

Standard:

1000°C (1832°F)


Text in Illustration
*1 Exhaust Gas Temperature Sensor (bank 1 sensor 1)
*2 ECM
*3 Component with harness connected
(ECM)


h.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - EXHAUST GAS TEMPERATURE SENSOR)

NG

4.READ VALUE USING INTELLIGENT TESTER (SHORT IN WIRE HARNESS)
a.
A083863E71
0.781,0.333 1.01,0.521 0.229,0.188 10 false *1 2.417,1.031 2.771,1.219 0.354,0.188 10 false THCI 2.677,0.198 2.875,0.396 0.198,0.198 10 false *2 2.417,1.385 2.667,1.573 0.25,0.188 10 false E2

Disconnect the exhaust gas temperature sensor (bank1 sensor 1) connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S1.


f.

Read the value.

Standard:

0°C (32°F)


Text in Illustration
*1 Exhaust Gas Temperature Sensor (bank 1 sensor 1)
*2 ECM


g.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPLACE EXHAUST GAS TEMPERATURE SENSOR (BANK 1 SENSOR 1)

NG

5.READ VALUE USING INTELLIGENT TESTER (SHORT IN ECM)
5.READ VALUE USING INTELLIGENT TESTER (SHORT IN ECM)
a.
A116781E11
1.25,2.958 1.646,3.198 0.396,0.24 1.677,3.885 2.031,4.229 true 0.708,0.417 0.875,0.625 0.167,0.208 10 false *1 1.313,3 1.594,3.198 0.281,0.198 10 false B60 2.375,1.271 2.75,1.448 0.375,0.177 10 false THCI 2.094,4.208 2.469,4.396 0.375,0.188 10 false THCI 2.365,1.688 2.594,1.885 0.229,0.198 10 false E2 2.667,0.417 2.833,0.625 0.167,0.208 10 false *2 0.469,2.25 0.635,2.458 0.167,0.208 10 false *3

Disconnect the exhaust gas temperature sensor (bank1 sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S1.


g.

Read the value.

Standard:

0°C (32°F)


Text in Illustration
*1 Exhaust Gas Temperature Sensor (bank 1 sensor 1)
*2 ECM
*3 Rear view of wire harness connector
(to ECM)


h.

Reconnect the exhaust gas temperature sensor connector.


i.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - EXHAUST GAS TEMPERATURE SENSOR)

NG