Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P2BAC  NOx Exceedance - Deactivation of EGR  


DESCRIPTION

The EGR system recirculates exhaust gases, in order to suit every driving condition. The recirculated gas mingles with intake air, therefore the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emission.

In order to increase EGR circulation efficiency, the ECM adjusts the lift amount of the electric EGR control valve and throttle valve angle.

DTC No. DTC Detection Condition Trouble Area
P2BAC When following condition (a) and (b) are met:
(1 trip detection logic)
(a) Battery voltage is 19.9 V or more
(b) One of the following conditions 1, 2 or 3 is met
1.

Open or short in EGR valve assembly circuit

2.

Open or short in EGR valve position sensor circuit

3.

EGR position are out of specified threshold and battery voltage 10 V or more


·

EGR valve assembly stuck

·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM



MONITOR DESCRIPTION

When the target and actual positions of the electric EGR control valve are different, the ECM interprets this as a malfunction of the electric EGR control valve and illuminates the MIL.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

When this DTC is stored the vehicle enters fail-safe mode, in which the MIL blinks and the ECM measures elapsed time until an idle signal has been input or engine speed is below 200 rpm after 36 hours, after which engine output is limited to 75%.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2BAC)
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result:
Result Proceed to
P2BAC A
P2BAC and other DTCs B


HINT:

If any DTCs other than P2BAC are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE EGR STEP POSITION)
a.

Turn the ignition switch off and wait for 60 seconds.


b.

Connect an intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the tester on.


e.

Warm up the engine until the engine coolant temperature reaches 80°C (176°F).


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / MAF.


g.

Read the MAF value during the Active Test.

Result:
Active Test Result Proceed to
0 to 100% MAF value is not changed A
MAF value is changed B


NOTICE:

In the table below, the values listed under "MAF Value" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


Reference
EGR Valve Status Condition MAF Value
Open (21%) Atmosphere pressure: 101 kPa
Intake air temperature: 25°C
Engine coolant temperature: 70°C
10.0 to 12.0 g/sec
Close (0%) 15.0 to 17.0 g/sec



A

3.INSPECT EGR VALVE ASSEMBLY

B

6.INSPECT EGR VALVE ASSEMBLY (EGR VALVE OPERATION)
3.INSPECT EGR VALVE ASSEMBLY
a.
A101433E09
0.125,0.094 0.354,0.302 0.229,0.208 10 false *1

Disconnect the EGR valve assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 5 20°C (68°F) 6.5 to 7.5 Ω


Text in Illustration
*1 Component without harness connected
(EGR Valve Assembly)


c.

Reconnect the EGR valve assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)
a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B60-3 (EGRS) - B47-1 (EGR) Always Below 1 Ω
B60-3 (EGRS) or B47-1 (EGR) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the EGR valve assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK EGR VALVE ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK EGR VALVE ASSEMBLY (POWER SOURCE)
a.
A101429E09
0.24,1.01 0.677,1.26 0.438,0.25 2.167,1.094 2.563,0.823 true 0.104,0.052 0.375,0.26 0.271,0.208 10 false *1 0.323,1.052 0.656,1.25 0.333,0.198 10 false B47 2.625,0.708 2.938,0.896 0.313,0.188 10 false +B

Disconnect the EGR valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B47-5 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*1 Front view of wire harness connector
(to EGR Valve Assembly)


d.

Reconnect the EGR valve assembly connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT EGR VALVE ASSEMBLY (EGR VALVE OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - NO. 2 INTEGRATION RELAY)

6.INSPECT EGR VALVE ASSEMBLY (EGR VALVE OPERATION)
a.

Remove the EGR valve assembly.


b.

Inspect the EGR valve assembly.

i.

Visually check the EGR valve assembly for deposits.

OK:

No deposits around the EGR valve.



ii.

Visually check that there is no gap between the valve and body.

OK:

No gap between the valve and body.


Result:
Result Proceed to
NG A
OK B




c.

Reinstall the EGR valve assembly.



A

7.REPLACE EGR VALVE ASSEMBLY

B

8.CHECK FOR BLOCKAGE IN EGR GAS PASSAGE (EXHAUST MANIFOLD - EGR COOLER - EGR VALVE ASSEMBLY)
7.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly (Click here Engine / Hybrid System>N04C-UH (EMISSION CONTROL)>EGR VALVE>REMOVAL).


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR BLOCKAGE IN EGR GAS PASSAGE (EXHAUST MANIFOLD - EGR COOLER - EGR VALVE ASSEMBLY)
8.CHECK FOR BLOCKAGE IN EGR GAS PASSAGE (EXHAUST MANIFOLD - EGR COOLER - EGR VALVE ASSEMBLY)
a.

Check for blockage in the EGR gas passage from the exhaust manifold, through the EGR cooler assembly to the EGR valve assembly.

OK:

No blockage in the EGR gas passage.



Result:
Result Proceed to
NG A
OK B



A

9.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

B

10.CHECK WHETHER DTC OUTPUT RECURS
9.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
a.

Repair or replace the malfunctioning parts, component and area.


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS
10.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F).


e.

Drive the vehicle at 50 km/h (31 mph) or more and then fully release the accelerator pedal for 5 seconds or more (Procedure "A").


f.

Repeat procedure "A" several times.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Read the DTC.


Result:
Result Proceed to
P2BAC A
No output B



A

B

END