Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0045  Turbo / Super Charger Boost Control Solenoid Circuit / Open  


DESCRIPTION

The turbocharger sub-assembly (variable nozzle controller) operates steplessly according to the internal DC brushless motor and controls the turbine speed and turbocharging pressure.

The turbocharger sub-assembly (variable nozzle controller) has a position sensor which detects the nozzle position and continuously monitors the target position and actual position of the nozzle.

When the engine is stopped, wiping is performed to clean away accumulated oil and soot from the nozzle operating range and to check that there is no abnormality with the mechanical operation of the turbocharger.

DTC No. DTC Detection Condition Trouble Area
P0045 The ignition switch is on (IG), battery voltage is 11 to 14 V, engine stopped or 5 seconds or more elapse with engine speed at 500 rpm or more (1 trip detection logic).
When one of the following conditions is met:
·

Follow-up failure detected due abnormal movement or the variable nozzle operation link being stuck

·

Abnormally high temperature detected in turbocharger sub-assembly (variable nozzle controller)

·

Open or short in the internal motor or position sensor of the turbocharger sub-assembly (variable nozzle controller)

·

The stopper position of the variable nozzle operation link has deviated and an operating range malfunction is detected


·

Turbocharger sub-assembly (variable nozzle controller)

·

Variable nozzle operation link jamming or stop position deviation

·

Temperature increase around turbocharger sub-assembly (variable nozzle controller)

·

ECM



A385724E01
0.552,0.802 1.01,1 0.458,0.198 10 false 12V 0.531,1.51 0.99,1.708 0.458,0.198 10 false GND 2.021,1.448 2.531,2.063 0.51,0.615 10 false Power Source Block 3.885,0.948 4.688,1.344 0.802,0.396 10 false Moror Driver I/F Block 5.948,2.542 6.854,2.969 0.906,0.427 10 false DC Brushless Motor 5.271,1.479 6.063,1.698 0.792,0.219 10 false Motor (U) 5.271,2.115 6.063,2.333 0.792,0.219 10 false Motor (V) 5.271,2.75 6.063,2.969 0.792,0.219 10 false Motor (W) 0.448,2.719 1.24,2.938 0.792,0.219 10 false CAN-H 0.448,2.99 1.24,3.208 0.792,0.219 10 false CAN-L 1.396,3.25 2.427,3.479 1.031,0.229 10 false CAN I/F Block 1.573,4.542 2.604,4.771 1.031,0.229 10 false EEPROM 3.844,3.625 4.875,4.01 1.031,0.385 10 false Overcurrent Protection Block 3.771,4.365 4.771,4.75 1,0.385 10 false Position Sensor I/F Block 5.073,4.219 5.865,4.448 0.792,0.229 10 false P/S (U,V,W) 5.073,4.667 6.177,4.958 1.104,0.292 10 false P/S (U+,V+,W+) 5.833,3.604 6.854,4.01 1.021,0.406 10 false Position Sensor (Hall IC) 2.917,0.094 4.969,0.292 2.052,0.198 10 false Variable Nozzle Ccontroller 2.771,1.792 3.229,1.99 0.458,0.198 10 false ECU

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0045
·

Idle for 5 seconds or more after engine warm-up

·

Wiping performed after turning the ignition switch on (IG) to off



WIRING DIAGRAM

A398540E04
1.031,2.323 3.24,2.677 2.208,0.354 10 false Turbocharger Actuator (built into Turbocharger Sub-assembly) 2.094,0.417 2.563,0.625 0.469,0.208 10 false CANH 2.115,0.865 2.583,1.073 0.469,0.208 10 false CANL 2.188,1.302 2.656,1.51 0.469,0.208 10 false HLG 2.177,1.729 2.646,1.938 0.469,0.208 10 false HLV 1.042,2.094 1.51,2.302 0.469,0.208 10 false j5 5.573,0.865 6.042,1.073 0.469,0.208 10 false B104 5.573,0.427 6.042,0.635 0.469,0.208 10 false B104 6.031,0.427 6.5,0.635 0.469,0.208 10 false CAN+ 6.021,0.875 6.49,1.083 0.469,0.208 10 false CAN- 4.479,2.427 5.177,2.635 0.698,0.208 10 false EFI NO. 3 6.021,3.948 6.49,4.156 0.469,0.208 10 false MREL 2.99,4.74 4.531,5.021 1.542,0.281 10 false No. 2 Integration Relay 1.25,4.833 1.948,5.042 0.698,0.208 10 false Battery 0.667,3.979 1.365,4.188 0.698,0.208 10 false FL MAIN 0.667,3.583 1.573,3.76 0.906,0.177 10 false R/B NO. 2-B 1.688,3.583 2.156,3.792 0.469,0.208 10 false P/I 2.51,3.438 2.979,3.646 0.469,0.208 10 false 2E 2.5,3.927 2.969,4.135 0.469,0.208 10 false 2D 4.677,3.938 5.146,4.146 0.469,0.208 10 false 2D 4.677,3.438 5.146,3.646 0.469,0.208 10 false 2D 5.615,3.938 6.083,4.146 0.469,0.208 10 false A56 3.896,4.24 4.365,4.448 0.469,0.208 10 false EFI 6.188,4.979 6.656,5.188 0.469,0.208 10 false ECM 2.542,3.219 2.948,3.458 0.406,0.24 10 false 1 2.542,3.729 2.948,3.969 0.406,0.24 10 false 3 4.719,3.74 5.125,3.979 0.406,0.24 10 false 2 4.719,3.24 5.125,3.479 0.406,0.24 10 false 4 2.563,1.615 2.969,1.854 0.406,0.24 10 false 1 2.573,0.688 2.979,0.927 0.406,0.24 10 false 3 2.573,1.156 2.979,1.396 0.406,0.24 10 false 2 2.573,0.25 2.979,0.49 0.406,0.24 10 false 4 5.667,0.229 6.073,0.469 0.406,0.24 10 false 12 5.708,0.677 6.115,0.917 0.406,0.24 10 false 6 5.656,3.729 6.063,3.969 0.406,0.24 10 false 25 2.927,3.583 3.625,3.792 0.698,0.208 10 false EFI-MAIN

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0045)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.


Result:
Result Proceed to
DTC P0045 and other DTCs are output A
DTC P0045 is output B



A

2.PERFORM CHECKS AND REPAIRS FOR DTCS

B

3.CHECK WHETHER DTC OUTPUT RECURS
2.PERFORM CHECKS AND REPAIRS FOR DTCS

b.

Perform checks on the malfunctioning parts for related DTCs.


Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for 30seconds or more.


f.

Turn the ignition switch to ON.


g.

Turn the ignition switch off and wait for 5 seconds or more.

HINT:

The variable nozzle controller performs the wiping operation.



h.

Connect the GTS to the DLC3.


i.

Turn the ignition switch to ON.


j.

Turn the GTS on.


k.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.



Result:
Result Proceed to
DTC P0045 is not output A
DTC P0045 is output B



A

4.CHECK TURBOCHARGER SUB-ASSEMBLY

B

8.VISUALLY CHECK TURBOCHARGER SUB-ASSEMBLY (VARIABLE NOZZLE CONTROLLER)
4.CHECK TURBOCHARGER SUB-ASSEMBLY
A385725E01
1.969,0.208 2.125,0.406 0.156,0.198 10 false A

a.

Check that there are no possible causes for a temperature increase around the turbocharger subassembly (variable nozzle controller).

OK:

Check that there are no holes in the insulator, cracks, or exhaust gas leaks that could lead to an increase in temperature.


HINT:

If the temperature of the variable nozzle controller upper surface (A) rises, P0045 is output.



Result:
Proceed to
OK
NG



OK

5.VISUALLY CHECK TURBOCHARGER SUB-ASSEMBLY (VARIABLE NOZZLE CONTROLLER)

NG

REPAIR THE CAUSE OF THE TEMPERATURE INCREASE AROUND THE VARIABLE NOZZLE CONTROLLER

5.VISUALLY CHECK TURBOCHARGER SUB-ASSEMBLY (VARIABLE NOZZLE CONTROLLER)
a.

Check that no foreign matter is stuck around the turbocharger sub-assembly (variable nozzle controller) variable nozzle link.


A385726

Result:
Result Proceed to
Foreign objects stuck around the variable nozzle link
(proceed to the next procedure after removing the foreign objects)
B
No foreign objects stuck around the variable nozzle link A



A

6.PERFORM ACTIVE TEST USING USING GTS (TEST THE TURBO CHARGER STEP MOTOR)

B

9.CHECK THE OPERATION OF THE TURBOCHARGER SUB-ASSMBLY (VARIABLE NOZZLE CONTROLLER)
6.PERFORM ACTIVE TEST USING USING GTS (TEST THE TURBO CHARGER STEP MOTOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Turbo Charger Step Motor / Data List / Actual VN Turbo Position and Target VN Turbo Position.


e.

Perform the Active Test and check that the "Actual VN Turbo Position" values follow the "Target VN Turbo Position" values.

NOTICE:

Perform this procedure with the engine stopped as the engine may be damaged.


OK:

"Actual VN Turbo Position" moves to the "TargetVN Turbo Position" within 3 seconds.



Result:
Proceed to
OK
NG



OK

7.CHECK THE PAST REPAIR HISTORY

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY

7.CHECK THE PAST REPAIR HISTORY
a.

Check that any previously output turbocharger subassembly DTCs have been from the past repair history.

HINT:

There are cases where previously stored P0045 DTCs were not cleared during repair work. However, malfunctions such as the MIL illuminating, a drop in engine output is detected or black smoke being emitted after performing repairs is not the result of DTCs not being cleared. Therefore, replace the turbocharger sub-assembly (variable nozzle controller).


OK:

No entries for turbocharger sub-assembly DTCs in the past repair history. Also, no MIL illumination, lack or power or black smoke emission noted after previous repairs.



Result:
Proceed to
OK
NG



OK

END (DTC LEFT BEHIND FROM PAST REPAIR)

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY

8.VISUALLY CHECK TURBOCHARGER SUB-ASSEMBLY (VARIABLE NOZZLE CONTROLLER)
a.

Check that no foreign matter is stuck around the turbocharger sub-assembly (variable nozzle controller) variable nozzle link.


A385726

Result:
Result Proceed to
Foreign objects stuck around the variable nozzle link
(proceed to the next procedure after removing the foreign objects)
A
No foreign objects stuck around the variable nozzle link B



A

9.CHECK THE OPERATION OF THE TURBOCHARGER SUB-ASSMBLY (VARIABLE NOZZLE CONTROLLER)

B

REPLACE TURBOCHARGER SUB-ASSEMBLY

9.CHECK THE OPERATION OF THE TURBOCHARGER SUB-ASSMBLY (VARIABLE NOZZLE CONTROLLER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for 5 seconds or more.

HINT:

The variable nozzle controller performs the wiping operation.



f.

Turn the GTS on.


g.

Turn the ignition switch to ON and wait for 5 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.



Result:
Result Proceed to
DTC P0045 is not output* A
DTC P0045 is output B

*: P0045 is output according to a jamming malfunction in the variable nozzle operation link



A

10.PERFORM ACTIVE TEST USING USING GTS (TEST THE TURBO CHARGER STEP MOTOR)

B

REPLACE TURBOCHARGER SUB-ASSEMBLY

10.PERFORM ACTIVE TEST USING USING GTS (TEST THE TURBO CHARGER STEP MOTOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Turbo Charger Step Motor / Data List / Actual VN Turbo Position and Target VN Turbo Position.


e.

Perform the Active Test and check that the "Actual VN Turbo Position" values follow the "Target VN Turbo Position" values.

NOTICE:

Perform this procedure with the engine stopped as the engine may be damaged.


OK:

"Actual VN Turbo Position" moves to the "Target VN Turbo Position" within 3 seconds.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY