Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0400  Exhaust Gas Recirculation Flow  


DESCRIPTION

The EGR system recirculates exhaust gases, in order to suit every driving condition. The recirculated gas mingles with intake air, therefore the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emission.

In order to increase EGR circulation efficiency, the ECM adjusts the lift amount of the EGR valve assembly and throttle valve angle.

DTC No. DTC Detection Condition Trouble Area
P0400 EGR air flow rate less than the specified value when following conditions (a), (b), (c), (d), (e) and (f) are met: (1 trip detection logic)

(a) Engine speed is stable

(b) Fuel quantity is stable

(d) EGR valve assembly opening angle is 5% or more

(e) Exhaust brake system does not operate

(f) Mass air flow meter sub-assembly circuit malfunction, EGR valve assembly circuit malfunction, manifold absolute pressure sensor circuit malfunction and intake air temperature sensor (after turbocharged) circuit malfunction are not detected


·

EGR valve assembly stuck

·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM



MONITOR DESCRIPTION

When the target and actual positions of the EGR valve assembly are different, the ECM interprets this as a malfunction of the EGR valve assembly and illuminates the MIL.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

When this DTC is stored the vehicle enters fail-safe mode, in which the MIL blinks and the ECM measures elapsed time until an idle signal has been input or engine speed is below 200 rpm after 36 hours, after which engine output is limited to 75%.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0400)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
P0400 A
P0400 and other DTCs B


HINT:

If any DTCs other than P0400 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Turn the ignition switch off and wait for 60 seconds.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Warm up the engine until the engine coolant temperature reaches 80°C (176°F).


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / MAF.


g.

Read the MAF value during the Active Test.

Result:
Active Test Result Proceed to
0 to 100% MAF value is not changed A
MAF value is changed B



NOTICE:

In the table below, the values listed under "MAF Value" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


Reference
EGR Valve Status Condition MAF Value
Open (21%) Atmosphere pressure: 101 kPa
Intake air temperature: 25°C
Engine coolant temperature: 70°C
10.0 to 12.0 gm/s
Close (0%) 15.0 to 17.0 gm/s


A

3.INSPECT EGR VALVE ASSEMBLY

B

5.INSPECT EGR VALVE ASSEMBLY (EGR VALVE OPERATION)
3.INSPECT EGR VALVE ASSEMBLY

Result:
Proceed to
OK
NG



OK

4.CHECK EGR VALVE ASSEMBLY (POWER SOURCE)

NG

4.CHECK EGR VALVE ASSEMBLY (POWER SOURCE)
a.
A430807E01
1.521,0.302 1.938,0.563 0.417,0.26 0.823,0.708 1.479,1.083 true 0.917,1.667 1.5,1.354 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 0.635,0.583 0.948,0.781 0.313,0.198 10 false E 0.656,1.604 0.969,1.802 0.313,0.198 10 false +B 1.594,0.344 2.063,0.542 0.469,0.198 10 false B48

Disconnect the EGR valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B48-4 (+B) - B48-1 (E) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to EGR Valve Assembly)


Result:
Proceed to
OK
NG



OK

5.INSPECT EGR VALVE ASSEMBLY (EGR VALVE OPERATION)

NG

10.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - BODY GROUND)
5.INSPECT EGR VALVE ASSEMBLY (EGR VALVE OPERATION)
a.

Remove the EGR valve assembly.


b.

Inspect the EGR valve assembly.

i.

Visually check the EGR valve assembly for deposits.

OK:

No deposits around the EGR valve.



ii.

Visually check that there is no gap between the valve and body.

OK:

No gap between the valve and body.




Result:
Result Proceed to
NG A
OK B



A

6.REPLACE EGR VALVE ASSEMBLY

B

7.CHECK FOR BLOCKAGE IN EGR GAS PASSAGE (EXHAUST MANIFOLD - EGR COOLER SUB-ASSEMBLY - EGR VALVE ASSEMBLY)
6.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly (Click hereEngine / Hybrid System>N04C-VQ (EMISSION CONTROL)>EGR VALVE>REMOVAL).


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR BLOCKAGE IN EGR GAS PASSAGE (EXHAUST MANIFOLD - EGR COOLER SUB-ASSEMBLY - EGR VALVE ASSEMBLY)
7.CHECK FOR BLOCKAGE IN EGR GAS PASSAGE (EXHAUST MANIFOLD - EGR COOLER SUB-ASSEMBLY - EGR VALVE ASSEMBLY)
a.

Check for blockage in the EGR gas passage from the exhaust manifold, through the EGR cooler sub-assembly to the EGR valve assembly.

OK:

No blockage in the EGR gas passage.



Result:
Result Proceed to
NG A
OK B



A

8.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

B

9.CHECK WHETHER DTC OUTPUT RECURS
8.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
a.

Repair or replace the malfunctioning parts, component and area.


Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS
9.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F).


e.

Drive the vehicle at 50 km/h (31 mph) or more and then fully release the accelerator pedal for 5 seconds or more (Procedure "A").


f.

Repeat procedure "A" several times.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTC.


Result:
Result Proceed to
DTC P0400 is output A
DTC is not output B



A

B

END

10.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - BODY GROUND)
a.

Disconnect the EGR valve assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - NO. 2 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - BODY GROUND)

11.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - NO. 2 INTEGRATION RELAY)
a.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the EGR valve assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-4 (+B) - 2D-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EGR VALVE ASSEMBLY - NO. 2 INTEGRATION RELAY)