Home › Engine / Hybrid System › N04C-VL (ENGINE MECHANICAL) › CYLINDER HEAD › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073160 N04C-VL ENGINE MECHANICAL _0356003 CYLINDER HEAD A

N04C-VL ENGINE MECHANICAL  CYLINDER HEAD  REMOVAL  


PROCEDURE

Hide 16400 1.REMOVE RADIATOR ASSEMBLY

Hide 17201 2.REMOVE TURBOCHARGER SUB-ASSEMBLY

Hide 23670 3.REMOVE INJECTOR ASSEMBLY

Hide 87208L 6.REMOVE WATER PIPE SUB-ASSEMBLY

Hide 16206B 7.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A348683

Disconnect the engine coolant temperature sensor connector and camshaft position sensor connector.


b.

Disconnect the water hose.


c.

Remove the 2 bolts and the No. 3 water by-pass pipe sub-assembly.


Hide 16206 8.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 27020 9.REMOVE GENERATOR ASSEMBLY

Hide 16331A 11.REMOVE THERMOSTAT

a.

Remove the thermostat from the water outlet housing.


b.

Remove the gasket from the thermostat.


Hide 16333 12.REMOVE WATER OUTLET HOUSING

Hide 17111 13.REMOVE INTAKE MANIFOLD

a.
A344319

Remove the 8 bolts, 2 nuts and the intake manifold.

Text in Illustration
V100135

Bolt
V100136

Nut


Hide 17141 14.REMOVE EXHAUST MANIFOLD

a.
A155964

Remove the 3 bolts and exhaust manifold heat insulator.


b.
A155965

Remove the 8 nuts, 4 spacers, 4 collars and the exhaust manifold.


c.

Remove the 4 exhaust manifold gaskets.


Hide 15.SET NO. 1 CYLINDER TO TDC / COMPRESSION

a.
A146510E12
2.635,1.021 1.875,0.198 false 1.677,0.094 1.875,0.365 0.198,0.271 10 false *a

Turn the crankshaft pulley until the groove of the crankshaft damper and the timing mark on the timing gear are aligned.

Text in Illustration
*a Timing Mark

HINT:
·

Make sure that there is free play in the No. 1 cylinder rocker arms and there is no free play in the No. 4 cylinder rocker arms.

·

If not, turn the crankshaft 1 revolution (360°) to set the No. 1 cylinder to TDC/compression.




Hide 13901 16.REMOVE NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY

a.
A151464E08
1.917,1 1.563,0.292 false 1.906,1.115 1.448,1.927 false 1.344,0.177 1.521,0.354 0.177,0.177 10 false *1 1.24,1.865 1.417,2.042 0.177,0.177 10 false *2

Loosen the lock nuts at the top of the rocker arms and wind up the adjusting screws completely.

Text in Illustration
*1 Adjusting Screw
*2 Lock Nut

NOTICE:

If the adjusting screws are left unwound, the rocker shaft may bend when the rocker arm support bolts are loosened.



b.
A151465E01
0.412,0.326 0.516,0.477 0.104,0.152 10 1 1.035,0.326 1.139,0.477 0.104,0.152 10 3 1.657,0.326 1.761,0.477 0.104,0.152 10 5 2.283,0.326 2.388,0.477 0.104,0.152 10 4 2.9,0.326 3.004,0.477 0.104,0.152 10 2

Loosen the 5 rocker arm support bolts in the order shown in the illustration.


c.

Remove the No. 1 valve rocker shaft sub-assembly.


Hide 13781 17.REMOVE VALVE PUSH ROD

a.

Remove the valve push rod.

HINT:

Organize the parts so that each part location can be remembered for reassembly.



Hide 13819 18.REMOVE VALVE BRIDGE

a.

Remove the valve bridge.

HINT:

Organize the parts so that each part location can be remembered for reassembly.



Hide 11101 19.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A141062

Remove the 22 cylinder head bolts in 3 steps in the sequence shown in the illustration.


b.

Lift and remove the cylinder head sub-assembly from the cylinder block.


Hide 11115 20.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket.


Hide 13751 21.REMOVE VALVE LIFTER

a.

Remove the valve lifter.

HINT:

Organize the parts so that each part location can be remembered for reassembly.