16400
1.REMOVE RADIATOR ASSEMBLY
33110
2.REMOVE MANUAL TRANSMISSION ASSEMBLY
31250
3.REMOVE CLUTCH DISC ASSEMBLY
(Click hereDrivetrain>CLUTCH>CLUTCH UNIT (for M551)>REMOVAL)
17201
4.REMOVE TURBOCHARGER SUB-ASSEMBLY
16577C
5.REMOVE RADIATOR PIPE
Remove the 2 bolts and remove the radiator pipe.
Remove the O-ring.
88320
6.SEPARATE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
Disconnect the connector.
Remove the 6 bolts and separate the cooler compressor assembly.
27020
7.REMOVE GENERATOR ASSEMBLY
44360
8.SEPARATE VANE PUMP OIL RESERVOIR ASSEMBLY
Remove the 3 bolts and vane pump oil reservoir assembly.
53712C
9.REMOVE FRONT FENDER APRON LH
44310
10.SEPARATE VANE PUMP ASSEMBLY
Remove the 2 bolts and separate the vane pump assembly.
Remove the O-ring.
17342P
11.REMOVE NO. 2 AIR HOSE
44774
12.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Disconnect the union to connector tube hose.
22100A
13.DISCONNECT INJECTION PUMP TO FUEL FILTER FUEL HOSE OR PIPE
14.DISCONNECT NO. 1 FUEL HOSE RETURN TUBE
28100
15.REMOVE STARTER ASSEMBLY
45470
16.SEPARATE TIE ROD ASSEMBLY LH
Remove the cotter pin.
Remove the nut.
Using SST, separate the tie rod assembly LH from the steering relay rod assembly.
45450
17.SEPARATE STEERING RELAY ROD ASSEMBLY
Remove the 2 cotter pins.
Remove the 2 nuts.
Using SST, separate the steering relay rod assembly from the center arm.
| *a | for RH Side |
| *b | for LH Side |
51202D
18.REMOVE FRONT LOWER SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Remove the 6 bolts, 4 washers and 4 nuts and remove the front lower suspension crossmember sub-assembly.
82121
19.SEPARATE ENGINE WIRE
Separate all engine wires from the engine.
20.REMOVE ENGINE ASSEMBLY
Support the engine using an engine lifter.
Remove the 2 nuts and washer.
|
Bolt |
|
Nut |
Remove the 4 bolts and front No. 1 engine mounting bracket LH.
Remove the engine mounting stabilizer and engine mounting insulator.
Remove the 2 nuts and washer.
Remove the 4 bolts and front No. 1 engine mounting bracket RH.
|
Bolt |
|
Nut |
Remove the engine mounting stabilizer and engine mounting insulator.
Remove the engine assembly.
12180E
21.REMOVE OIL FILLER CAP SUB-ASSEMBLY
Remove the oil filler cap sub-assembly.
11202D
22.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 2 bolts and No. 2 cylinder head cover sub-assembly.
25625
23.REMOVE EGR VALVE BRACKET
Remove the 4 bolts and EGR valve bracket.
15301
24.REMOVE OIL DIPSTICK GUIDE
Remove the bolt and oil dipstick guide.
Remove the O-ring.
25.REMOVE INTAKE PIPE WITH VENTURI ASSEMBLY
11201
26.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the wire harness.
Remove the cylinder head cover cushion rubber.
Remove the 2 bolts, 2 cushions, 2 spacers and cylinder head cover sub-assembly.
17138A
27.REMOVE INTAKE PIPE STAY
Remove the 4 bolts and intake pipe.
23741B
28.REMOVE INJECTION PIPE CLAMP
23670
29.REMOVE INJECTOR ASSEMBLY
17111
30.REMOVE INTAKE MANIFOLD
17141
31.REMOVE EXHAUST MANIFOLD
83530
32.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
15710
33.REMOVE OIL COOLER ASSEMBLY
15710C
34.REMOVE OIL COOLER GASKET
89422
35.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
36.REMOVE CRANKSHAFT POSITION SENSOR
37.REMOVE CAMSHAFT POSITION SENSOR
16630G
38.REMOVE IDLER PULLEY ASSEMBLY
Remove the 2 bolts and idler pulley assembly.
88444
39.REMOVE IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)
Remove the 3 bolts and idle pulley assembly with bracket.
88431
40.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
Remove the 7 bolts, compressor mounting bracket set and No. 1 compressor mounting bracket.
| *1 | Compressor Mounting Bracket Set |
| *2 | No. 1 Compressor Mounting Bracket |
16331
41.REMOVE WATER OUTLET
Remove the 3 bolts and water outlet.
16331A
42.REMOVE THERMOSTAT
16333
43.REMOVE WATER OUTLET HOUSING
Remove the 3 bolts and water outlet housing.
87208L
44.REMOVE WATER PIPE SUB-ASSEMBLY
Remove the 3 bolts, O-ring and water pipe sub-assembly.
16206B
45.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
Disconnect the water hose.
Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly.
16206
46.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 6 bolts, 6 O-rings and water by-pass pipe sub-assembly.
16100
47.REMOVE ENGINE WATER PUMP ASSEMBLY
23811
48.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE
23803H
49.REMOVE FUEL RETURN PIPE SUB-ASSEMBLY
19971E
50.REMOVE VACUUM PIPE
Remove the bolt and nut and remove the 2 pipe clamps.
29601B
51.REMOVE VACUUM PUMP OIL PIPE SUB-ASSEMBLY
29300
52.REMOVE VACUUM PUMP ASSEMBLY
53.REMOVE NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY
Remove the nut and fuel pipe clamp.
Loosen the hose clamp, 2 union bolts, 2 gaskets and the No. 3 nozzle leakage pipe sub-assembly.
23810A
54.REMOVE COMMON RAIL ASSEMBLY
23849G
55.REMOVE FUEL PIPE SUPPORT
Remove the 2 bolts and fuel pipe support.
82702E
56.REMOVE WIRING HARNESS BRACKET SUB-ASSEMBLY
Remove the 2 bolts and wiring harness bracket sub-assembly.
57.REMOVE COMMON RAIL ASSEMBLY FUEL PIPE SUPPORT
Remove the 2 bolts and common rail assembly fuel support.
22100
58.REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY