Home › Engine / Hybrid System › N04C-UH (ENGINE MECHANICAL) › CAMSHAFT
RM2850E _51 Engine / Hybrid System _073174 N04C-UH ENGINE MECHANICAL _0356073 CAMSHAFT A

N04C-UH ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 13501 1.INSTALL CAMSHAFT

a.
A151500E16
1.51,1.229 1.542,1.26 0.031,0.031 1.438,1.146 1.469,1.177 0.031,0.031 1.521,1.125 1.552,1.156 0.031,0.031 1.458,1.167 2.146,0.5 2.146,0.5 1.542,1.146 false 1.521,1.25 2.156,1.781 false 2.188,0.396 2.385,0.583 0.198,0.188 10 false *a 2.177,1.781 2.365,1.969 0.188,0.188 10 false *a

Apply engine oil to the camshaft journal and bearing.


b.

Match the alignment marks on the camshaft timing gear and oil pump gear and install the camshaft.

Text in Illustration
*a Alignment Mark


c.

Install the camshaft with the 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21ft.*lbf)



Hide 11301C 2.INSTALL TIMING CHAIN OR BELT COVER OIL SEAL

a.
A157089E01
2.446,1.508 2.737,1.653 0.291,0.145 10 SST 1.837,1.065 2.417,1.59 false

Using SST and a hammer, tap a new timing chain or belt cover oil seal into the timing gear case until the oil seal is flush with the timing gear edge.

SST
09223-78010  

NOTICE:
·

Be careful not to tap the timing chain or belt cover oil seal at an angle.

·

Keep the gap between the timing gear case edge and the timing chain or belt cover oil seal free of foreign matter.




b.

Apply MP grease to the oil seal lip.


Hide 11321C 3.INSTALL TIMING GEAR CASE

a.

Remove any old seal packing material from the contact surface.


b.

Apply a continuous bead of seal packing (diameter: 3 to 4 mm (0.118 to 0.157 in)) as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the belt cover within 3 minutes of applying the seal packing.

·

Do not expose the seal packing to engine oil for at least 2 hours after installing.




c.

Install the timing gear case with the 15 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



Hide 12270 4.INSTALL OIL SEPARATOR ASSEMBLY

a.

Install 3 new O-rings to the oil separator assembly and cylinder block.


b.

Install the oil separator assembly with the 5 bolts.

Torque:

55 N*m (561 kgf*cm, 41 ft.*lbf)



Hide 12101 5.INSTALL OIL PAN SUB-ASSEMBLY

a.
A146590E03
0.902,1.167 1.075,1.326 0.172,0.159 10 *1 1.611,0.693 1.145,1.235 1.145,1.235 1.611,1.882 false 1.611,0.693 1.145,1.235 1.145,1.235 1.611,1.882 false 1.611,0.693 1.145,1.235 1.145,1.235 1.611,1.882 false 1.861,4.109 1.861,4.342 false 1.779,4.358 1.929,4.517 0.149,0.159 10 *1

Remove any old seal packing material from the contact surface.


b.

Apply a continuous bead of seal packing (diameter: 3 to 4 mm (0.118 to 0.157 in.)) as shown in the illustration.

Text in Illustration
*1 Seal Packing

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan sub-assembly within 3 minutes of applying the seal packing.

·

Do not expose the seal packing to engine oil for at least 2 hours after installing.




c.

Install the oil pan sub-assembly with the 26 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



Hide 11351H 6.INSTALL FLYWHEEL HOUSING RH STAY

a.

Install the flywheel housing RH stay with the 4 bolts.

Torque:
for M14 bolt:

132 N*m (1346 kgf*cm, 97 ft.*lbf)

for M12 bolt:

97 N*m (989 kgf*cm, 72 ft.*lbf)



Hide 11351G 7.INSTALL FLYWHEEL HOUSING LH STAY

a.

Install the flywheel housing LH stay with the 4 bolts.

Torque:
for M14 bolt:

132 N*m (1346 kgf*cm, 97 ft.*lbf)

for M12 bolt:

97 N*m (989 kgf*cm, 72 ft.*lbf)



Hide 13470 8.INSTALL CRANKSHAFT PULLEY ASSEMBLY

a.
A151470

Install the crankshaft pulley and spacer onto the crankshaft.

HINT:

Align the pulley set key with the key groove of the pulley.



b.

Using a 46 mm socket wrench, tighten the nut.

Torque:

100 N*m (1020 kgf*cm, 74 ft.*lbf)


HINT:

Insert a screwdriver through the inspection hole of the flywheel housing into the ring gear of the flywheel to keep it from turning together with the crankshaft.



c.
A187774E01
1.102,0.517 1.498,0.677 0.396,0.16 10 90° 1.246,1.538 1.576,1.718 0.33,0.181 10 *a 1.626,1.153 1.598,1.191 1.598,1.191 1.551,1.257 false 1.551,1.257 1.377,1.499 false

Mark the front side of the nut with paint as shown in the illustration.

Text in Illustration
*a Paint
V100135

Front Side of Engine


d.

Retighten the nut by 90°.


Hide 13751 9.INSTALL VALVE LIFTER

NOTICE:

Be sure to install the push rod to its original position.


Hide 11115 10.INSTALL CYLINDER HEAD GASKET

Hide 11101 11.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13901 14.INSTALL NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY

Hide 29300 16.INSTALL VACUUM PUMP ASSEMBLY

Hide 19971E 17.INSTALL VACUUM PIPE

Hide 29601B 18.INSTALL VACUUM PUMP OIL PIPE SUB-ASSEMBLY

Hide 11301M 19.INSTALL CAMSHAFT POSITION SENSOR

Hide 27020 20.INSTALL GENERATOR ASSEMBLY

Hide 16100 21.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 88440B 22.INSTALL IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)

Hide 16630G 23.INSTALL IDLER PULLEY ASSEMBLY

Hide 88431 24.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 88320 25.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 16206C 26.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 27.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 87208L 28.INSTALL WATER PIPE SUB-ASSEMBLY

Hide 22100 30.INSTALL INJECTION OR SUPPLY PUMP ASSEMBLY

Hide 23670 31.INSTALL INJECTOR ASSEMBLY

Hide 17201 32.INSTALL TURBOCHARGER SUB-ASSEMBLY

Hide 16400 33.INSTALL RADIATOR ASSEMBLY