Home › Engine / Hybrid System › N04C-UH (FUEL) › FUEL SUPPLY PUMP › 2017.01–2021.01
RM2850E _51 Engine / Hybrid System _073175 N04C-UH FUEL _0356079 FUEL SUPPLY PUMP A

N04C-UH FUEL  FUEL SUPPLY PUMP  INSTALLATION  


PROCEDURE

Hide 13613 1.INSTALL INJECTION PUMP DRIVE GEAR

a.

Install a new O-ring onto the timer cover.


b.

Install the timer cover onto the injection or supply pump with the 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



c.

Install the crankshaft angle sensor plate and the drive gear with the nut.

Torque:

64 N*m (650 kgf*cm, 47 ft.*lbf)



Hide 22100 2.INSTALL INJECTION OR SUPPLY PUMP ASSEMBLY

a.
A146751E03
2.545,0.15 2.727,0.345 0.182,0.194 10 *a 2.952,0.584 3.138,0.779 0.186,0.194 10 *b 2.516,0.265 2.311,0.512 false 2.9,0.683 2.089,0.814 false

Install a new O-ring onto the timer cover.

Text in Illustration
*a Matchmark
*b Hole


b.

Turn the drive gear and align the hole with the matchmark as shown in the illustration.


c.
A146510E19
2.635,1.021 1.875,0.198 false 1.719,0.063 1.917,0.333 0.198,0.271 10 false *a

Check that the No. 1 cylinder is at TDC/ compression.

Text in Illustration
*a Timing Mark


d.
A165097E03
0.728,0.849 0.926,1.014 0.198,0.165 10 *a 1.632,0.943 0.951,0.943 false

Align the matchmarks of the timer cover and the front end plate, and then install the supply pump assembly with the 4 bolts.

Text in Illustration
*a Matchmark

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



e.
A101551

When the crankshaft position sensor's installation hole can be accessed directly:

i.

Check that the knock pin of the injection pump drive gear is at the center of the hole. Then, proceed to step (g).

If not, perform steps (b), (c), and (d) again.



f.
A146792E08
1.906,1.198 1.677,1.438 false 1.594,1.458 1.771,1.625 0.177,0.167 10 false *1 1.771,0.51 2.906,0.677 1.135,0.167 10 false 36 mm (1.42 in.) 2.385,1.438 3.417,1.76 1.031,0.323 10 false 6 mm (0.236 in.)

When the crankshaft position sensor installation hole cannot be accessed directly:

Text in Illustration
*1 Vinyl Tape

i.

Tape the screwdriver as shown in the illustration.


ii.
A146793E03
2.874,0.347 3.109,0.721 0.235,0.374 10 *1 2.854,0.478 2.227,1.187 false

Remove the service plug and gasket from the timing chain or belt cover sub-assembly.

Text in Illustration
*1 Service Plug


iii.
A146794E03
0.419,1.214 1.361,1.657 0.941,0.443 10 0 to 2 mm (0 to 0.0787 in.) 1.595,0.155 1.77,0.306 0.175,0.151 10 *1 1.055,0.475 1.219,0.628 0.164,0.153 10 *2 1.586,1.815 1.756,1.968 0.17,0.153 10 *3 1.809,1.896 2.396,1.827 false 1.272,0.567 1.451,0.83 false 1.815,0.251 2.197,0.717 false

Insert the screwdriver into the service plug hole.

Text in Illustration
*1 Timing Chain Cover
*2 Screwdriver
*3 Drive Gear


iv.

Check that the tape end and timing chain or belt cover sub-assembly are aligned as shown in the illustration.

If not, perform steps (b) and (c) again.


v.

Install the service plug and a new gasket to the timing chain cover sub-assembly.

Torque:

13 N*m (133 kgf*cm, 10 ft.*lbf)




g.

Install the holder clip with the bolt.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



h.

Connect the 2 connectors.


Hide 23803H 4.INSTALL FUEL RETURN PIPE SUB-ASSEMBLY

a.
A180216E02
2.979,0.313 3.146,0.479 0.167,0.167 10 true A 0.135,1.01 0.281,1.188 0.146,0.177 10 true B

Temporarily install the fuel return pipe sub-assembly and 3 new gaskets with the 2 union bolts.


b.

Tighten the 2 union bolts.

Torque:
Bolt A:

20 N*m (204 kgf*cm, 15 ft.*lbf)

Bolt B:

10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 23801L 5.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

a.

Temporarily install the fuel filter to injection pump fuel pipe with the union nuts.


b.

Using a union nut wrench (17 mm), tighten the fuel filter to injection pump fuel pipe with the 2 union nuts.

Torque:

35 N*m (357 kgf*cm, 26 ft.*lbf)


NOTICE:
·

If the supply pump assembly has been replaced, the fuel filter to injection pump fuel pipe must also be replaced.

·

Refer to the torque above when not using the union nut wrench. When using the union nut wrench, calculate the torque in accordance with the lengths of the union nut wrench and torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




c.

Install the pipe clamp with the nut. Tighten the nut until the clamp's edges make contact with the engine side clamp's edges.


Hide 6.INSTALL NO. 1 HARNESS BRACKET

a.

Install the No. 1 wire harness bracket with the 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



Hide 7.INSTALL NO. 2 HARNESS BRACKET

Hide 23807 8.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.

Install 2 new gaskets and the fuel delivery pipe with the union bolt.

Torque:

25 N*m (255 kgf*cm, 18 ft.*lbf)



Hide 23271H 9.CONNECT NO. 1 FUEL HOSE RETURN TUBE

a.

Connect the fuel hose.


Hide 22100A 10.CONNECT INJECTION PUMP TO FUEL FILTER FUEL HOSE OR PIPE

a.

Connect the fuel hose.


Hide 11.INSTALL NO. 2 INTAKE PIPE WITH EGR VALVE

Hide 16206 12.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 17113 13.INSTALL INTAKE PIPE WITH VENTURI ASSEMBLY

Hide 15301 14.INSTALL OIL DIPSTICK GUIDE

Hide 44360 16.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 25625B 17.INSTALL EGR VALVE BRACKET

Hide 18.INSTALL WIRE HARNESS AND CONNECTORS

Hide 25608 19.INSTALL EGR COOLER SUB-ASSEMBLY

Hide 17271 20.INSTALL NO. 1 TURBO INSULATOR

Hide 16206C 22.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 58701A 24.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for LHD)

Hide 58701A 25.INSTALL FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY (for RHD)

Hide 33504F 26.INSTALL SHIFT LEVER SUB-ASSEMBLY (for Manual Transmission)

Hide 58841A 27.INSTALL SHIFTING HOLE COVER (for Automatic Transmission)

Hide 33503F 28.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY (for Automatic Transmission)

Hide 33820B 29.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for RHD)

Hide 33820B 30.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for LHD)

Hide 58848A 31.INSTALL SHIFT LEVER HOLE COVER WITH BOOTS (for RHD)

Hide 32.BLEED AIR FROM FUEL SYSTEM

Hide 34.INSPECT FOR OIL LEAK

Hide 36.INITIALIZATION INJECTION OR SUPPLY PUMP ASSEMBLY

Hide 33531B 38.INSTALL SHIFT AND SELECT LEVER SHAFT DUST BOOT (for LHD)

Hide 58534A 39.INSTALL TRANSMISSION COVER MAT (for Manual Transmission)

Hide 58420 40.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY (for Automatic Transmission)

Hide 33820B 41.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 33820B 42.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 43. SHIFT LEVER POSITION (for Automatic Transmission)

Hide 58420 44.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58521D 45.INSTALL ENGINE SERVICE HOLE COVER MAT (w/o Carpet)

Hide 58734B 46.INSTALL ENGINE SERVICE COVER REAR WEATHERSTRIP

Hide 58410 47.INSTALL ENGINE SERVICE HOLE COVER

Hide 58521D 48.INSTALL ENGINE SERVICE HOLE COVER MAT (w/ Carpet)

Hide 51441D 49.INSTALL NO. 1 ENGINE UNDER COVER (for Plastic Type)

Hide 51441D 50.INSTALL NO. 1 ENGINE UNDER COVER (for Metal Type)

Hide 51459 51.INSTALL ENGINE SIDE COVER STAY (for TCAP Made)