22100
1.INSTALL INJECTION OR SUPPLY PUMP ASSEMBLY
Install the injection or supply pump assembly with the 4 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
23849G
2.INSTALL FUEL PIPE SUPPORT
Install the fuel support with the 2 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
Install the fuel support with the 2 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
23810A
3.INSTALL COMMON RAIL ASSEMBLY
Install the common rail assembly with the 2 bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
4.INSTALL NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY
Install the No. 3 nozzle leakage pipe sub-assembly with the 2 new gaskets and the 2 union bolts.
13 N*m (133 kgf*cm, 10 ft.*lbf)
Install the fuel pipe clamp with the nut. Tighten the nut until the clamp edges make contact.
29300
5.INSTALL VACUUM PUMP ASSEMBLY
19971E
6.INSTALL VACUUM PIPE
29601B
7.INSTALL VACUUM PUMP OIL PIPE SUB-ASSEMBLY
23811
8.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE
23803H
9.INSTALL FUEL RETURN PIPE SUB-ASSEMBLY
16100
10.INSTALL ENGINE WATER PUMP ASSEMBLY
16206C
11.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
Install the water by-pass pipe sub-assembly with 6 new O-rings and the 6 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
16206
12.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Connect the water hose.
Install the No. 2 water by-pass pipe sub-assembly with the 2 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
87208L
13.INSTALL WATER PIPE SUB-ASSEMBLY
Install the water pipe sub-assembly with a new O-ring and the 3 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
16331
14.INSTALL WATER OUTLET HOUSING
Apply a continuous bead of seal packing (width: 2.2 to 2.7 mm (0.0866 to 0.1063 in.)) as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
| *a | Seal Packing |
Remove any oil from the contact surface.
Install the water outlet housing within 3 minutes, and tighten the bolts within 15 minutes of applying the seal packing.
Install the water outlet housing with the 3 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
16331A
15.INSTALL THERMOSTAT
16331
16.INSTALL WATER OUTLET SUB-ASSEMBLY
Install the water outlet sub-assembly with the 3 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
88431
17.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
Install the No. 1 compressor mounting bracket and compressor mounting bracket set with the 7 bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
29 N*m (291 kgf*cm, 21 ft.*lbf)
First, temporarily tighten the bolts and check that the No. 1 compressor mounting bracket is seated properly. then, tighten the bolts to the specified torque.
88440B
18.INSTALL IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)
Install the idle pulley assembly with bracket with the 3 bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
16630G
19.INSTALL IDLER PULLEY ASSEMBLY
Install the idler pulley assembly with the 2 bolts.
55 N*m (561 kgf*cm, 41 ft.*lbf)
20.INSTALL CAMSHAFT POSITION SENSOR
Install the camshaft position sensor with the bolt.
12 N*m (122 kgf*cm, 9 ft.*lbf)
21.INSTALL CRANKSHAFT POSITION SENSOR
Install the crankshaft position sensor with the bolt.
12 N*m (122 kgf*cm, 9 ft.*lbf)
89422
22.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
Using a 19 mm deep socket wrench, install the water temperature sender gauge assembly with a new O-ring.
29 N*m (291 kgf*cm, 21 ft.*lbf)
15710C
23.INSTALL OIL COOLER GASKET
15710
24.INSTALL OIL COOLER ASSEMBLY
83530
25.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
17141
26.INSTALL EXHAUST MANIFOLD
17111
27.INSTALL INTAKE MANIFOLD
23670
28.INSTALL INJECTOR ASSEMBLY
23741B
29.INSTALL INJECTION PIPE CLAMP
17113
30.INSTALL NO. 2 INTAKE PIPE
| *1 | Seal Packing |
Apply a continuous bead of seal packing (width: 1.5 to 2.5 mm (0.0591 to 0.0984 in.)) as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Remove any oil from the contact surface.
Install the No. 2 intake pipe with EGR valve within 3 minutes, and tighten the bolts within 15 minutes of applying the seal packing.
Install the No. 2 intake pipe with EGR valve with the 4 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
17113D
31.INSTALL NO. 1 INTAKE PIPE
16206C
32.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
Install the water by-pass pipe sub-assembly with the 3 bolts, 2 union bolts and 4 new gaskets.
29 N*m (291 kgf*cm, 21 ft.*lbf)
25 N*m (250 kgf*cm, 18 ft.*lbf)
Connect the 2 water by-pass hoses to the EGR valve.
15301
33.INSTALL OIL DIPSTICK GUIDE
Install the oil dipstick guide with the bolt and new O-ring.
29 N*m (291 kgf*cm, 21 ft.*lbf)
25625B
34.INSTALL EGR VALVE BRACKET
Install the EGR valve bracket with the 4 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
11201
35.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Install 4 new No. 2 cylinder head cover gaskets onto the 4 injector assemblies.
Install new cylinder head cover gasket onto the cylinder head cover sub-assembly.
Install the 2 cushions, 2 spacers and tighten the 2 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
11202D
36.INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY
Install the No. 2 cylinder head cover sub-assembly with the 2 bolts.
29 N*m (291 kgf*cm, 21 ft.*lbf)
12180E
37.INSTALL OIL FILLER CAP SUB-ASSEMBLY
Install the oil filler cap sub-assembly.
38.INSTALL ENGINE ASSEMBLY
Support the engine with an engine lifter.
Install the engine assembly.
Install the front No. 1 engine mounting bracket LH with the 4 bolts.
69 N*m (704 kgf*cm, 51 ft.*lbf)
Install the engine mounting stabilizer and front engine mounting insulator with the 2 nuts.
87 N*m (887 kgf*cm, 64 ft.*lbf)
90 N*m (918 kgf*cm, 66 ft.*lbf)
|
Bolt |
|
Nut |
Install the front No. 1 engine mounting bracket RH with the 4 bolts.
69 N*m (704 kgf*cm, 51 ft.*lbf)
Install the engine mounting stabilizer and front engine mounting insulator with the 2 nuts.
87 N*m (887 kgf*cm, 64 ft.*lbf)
74 N*m (755 kgf*cm, 55 ft.*lbf)
|
Bolt |
|
Nut |
82121
39.INSTALL ENGINE WIRE
Install the engine wire.
51202D
40.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Install the front suspension crossmember sub-assembly with the 6 bolts and 4 nuts.
160 N*m (1631 kgf*cm, 118 ft.*lbf)
45450
41.INSTALL STEERING RELAY ROD ASSEMBLY
Install the steering relay rod assembly with the 3 nuts.
150 N*m (1530 kgf*cm, 111 ft.*lbf)
155 N*m (1581 kgf*cm, 115 ft.*lbf)
| *a | for RH Side |
| *b | for LH Side |
Install 3 new cotter pins.
45470
42.INSTALL TIE ROD ASSEMBLY LH
Remove the cotter pin.
Remove the nut.
Using SST, separate the tie rod end assembly LH from the steering relay rod assembly.
28100
43.INSTALL STARTER ASSEMBLY
22100A
44.CONNECT INJECTION PUMP TO FUEL FILTER FUEL HOSE OR PIPE
Connect the injection pump to fuel filter fuel hose or pipe.
23273U
45.CONNECT NO. 2 FUEL HOSE
Connect the No. 2 fuel hose.
44774
46.CONNECT UNION TO CONNECTOR TUBE HOSE
Connect the union to connector tube hose.
17342P
47.INSTALL NO. 2 AIR HOSE
44310
48.INSTALL VANE PUMP ASSEMBLY
Coat a new O-ring with power steering fluid and install it onto the vane pump assembly.
Install the vane pump assembly with the 2 bolts.
20 N*m (204 kgf*cm, 15 ft.*lbf)
53712C
49.INSTALL FRONT FENDER APRON LH
44360
50.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY
Install the vane pump oil reservoir assembly with the 3 bolts.
18 N*m (184 kgf*cm, 13 ft.*lbf)
27020
51.INSTALL GENERATOR ASSEMBLY
88320
52.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
Install the cooler compressor assembly with the 6 bolts.
47 N*m (475 kgf*cm, 34 ft.*lbf)
16577C
53.INSTALL RADIATOR PIPE
Install a new O-ring onto the radiator pipe.
Install the radiator pipe with the 2 bolts.
18 N*m (184 kgf*cm, 13 ft.*lbf)
17201
54.INSTALL TURBOCHARGER SUB-ASSEMBLY
17341F
55.INSTALL NO. 1 AIR HOSE
Install the No. 1 air hose with the bolt.
18 N*m (184 kgf*cm, 13 ft.*lbf)
Tighten the 2 No. 1 air hose clamp.
Connect the ventilation hose.
Install the wire harness.
31250
56.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)
35000
57.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
33110
58.INSTALL MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
16400
59.INSTALL RADIATOR ASSEMBLY