Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM2850E _59 Vehicle Exterior _073195 WINDOW / GLASS _0356202 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.



PROCEDURE

Hide 56111 1.CLEAN WINDSHIELD GLASS

a.
E268586

Clean the outer edge of the windshield glass with non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Do not damage the glass.

·

Even if using a new windshield glass, clean the windshield glass with non-residue solvent.




Hide 64818A 2.INSTALL BACK WINDOW GLASS SPACER

a.

Using non-residue solvent, clean the back window glass spacer installation surface of the vehicle body.


b.

Install the body primer to the back window glass spacer installation surface of the vehicle body.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new back window glass spacer.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 5 back window glass spacers to the body panel as shown in the illustration.

B474340E01
5.031,0.49 5.406,0.667 0.375,0.177 10 false A-A 2.563,0.5 2.719,0.667 0.156,0.167 10 true A 2.563,0.875 2.719,1.031 0.156,0.156 10 false A


Hide 56114C 3.INSTALL WINDSHIELD GLASS RETAINER

a.

Using non-residue solvent, clean the windshield glass retainer installation surface of the windshield glass.


b.

Install the glass primer to the windshield glass retainer installation surface of the windshield glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new windshield glass retainer.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the 5 windshield glass retainers to the windshield glass as shown in the illustration.

B474342E01
2.958,0.802 2.594,0.604 true 1.625,0.833 2.073,0.594 true 4.469,0.656 4.844,0.823 0.375,0.167 10 false A-A 5.031,1.083 5.177,1.26 0.146,0.177 10 false a 3.01,0.76 3.229,0.948 0.219,0.188 10 false *b 1.417,0.781 1.635,0.969 0.219,0.188 10 false *b 2.563,0.292 2.719,0.448 0.156,0.156 10 true A 2.563,0.865 2.719,1.021 0.156,0.156 10 false A 0.177,0.125 0.396,0.313 0.219,0.188 10 false *a

Text in Illustration
*a Back Side *b Ceramic Notch

Standard:
Area Specified Condition
a 19.8 mm (0.780 in.)



Hide 56116E 4.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.
B572396E02
0.75,0.177 1.063,0.375 0.313,0.198 10 false *A 2.177,0.188 2.49,0.385 0.313,0.198 10 false *B 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a

When reusing the windshield glass and a type A No. 2 windshield glass stopper is installed:

Text in Illustration
*A Type A
*B Type B
*a Back Side

HINT:

When a type A No. 2 windshield glass stopper is installed to the windshield glass, install a type B No. 2 windshield glass stopper (supply part) using the following procedures.


i.

Using non-residue solvent, clean the No. 2 windshield glass stopper installation surface of the windshield glass.


ii.
B571124E03
1.594,1.75 1.896,2.083 false 1.552,2.875 1.865,3.167 false 1.938,2.594 2.24,2.635 false 1.417,1.625 1.729,1.823 0.313,0.198 10 false *b 1.354,2.729 1.667,2.927 0.313,0.198 10 false *b 2.292,2.583 2.604,2.781 0.313,0.198 10 false *c 0.052,0.063 0.365,0.26 0.313,0.198 10 false *a

Draw a straight line connecting 2 ceramic notches on the windshield glass.

Text in Illustration
*a Back Side
*b Ceramic Notch
*c Straight Line


iii.

Using the *b ceramic notch as a standard, draw 3 straight lines perpendicular to the straight line from the ii above, and mark 3 *c stopper illustration markings at the positions indicated with the dimensions (surface dimensions) shown in the illustration.

B571125E02
1.26,2.26 0.99,2.281 false 0.563,3.802 0.271,4.042 0.271,4.042 0.271,4.344 false 4.719,4.365 4.458,4.365 4.458,4.365 4.229,4.594 false 5.531,4.76 5.385,5.031 5.385,5.031 5.146,5.031 false 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.813,2.208 1.125,2.458 0.313,0.25 10 false *b 1.448,4.302 1.604,4.5 0.156,0.198 10 true a 0.927,3.469 1.083,3.667 0.156,0.198 10 true b 3.479,4.719 3.646,4.938 0.167,0.219 10 true c 3.969,4.25 4.125,4.448 0.156,0.198 10 true d 6.188,4.813 6.344,5.01 0.156,0.198 10 true e 5.729,4.385 5.885,4.583 0.156,0.198 10 true f 0.229,4.396 0.531,4.615 0.302,0.219 10 true *c 4.781,4.271 5.125,4.573 0.344,0.302 10 false *c 4.948,4.948 5.344,5.281 0.396,0.333 10 false *c

Text in Illustration
*a Back Side *b Ceramic Notch
*c Stopper Installation Position Marking - -

Standard:
Area Specified Condition
a 48.3 mm (1.90 in.)
b 30.2 mm (1.19 in.)
c 15.2 mm (0.598 in.)
d 19.9 mm (0.783 in.)
e 11.4 mm (0.449 in.)
f 15.5 mm (0.610 in.)



iv.

Install the glass primer to the No. 2 windshield glass stopper installation surface of the windshield glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




v.
B571126E02
1.438,2.74 0.604,2.75 0.604,2.75 1.271,2.313 true 1.813,2.656 2.323,2.385 false 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.396,2.677 0.594,2.854 0.198,0.177 10 true *b 2.396,2.281 2.594,2.458 0.198,0.177 10 false *b

Peel the peeling paper from a new No. 2 windshield glass stopper, align it with the marked stopper installation position marking, and then install it in the position of the windshield glass shown in the illustration.

Text in Illustration
*a Back Side
*b Stopper Installation Position Marking



b.

When replacing the windshield glass, or a type B No. 2 windshield glass stopper is installed:

i.

Using non-residue solvent, clean the No. 2 windshield glass stopper installation surface of the windshield glass.


ii.

Install the glass primer to the No. 2 windshield glass stopper installation surface of the windshield glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




iii.

Remove the peeling paper from a new No. 2 windshield glass stopper.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iv.
B571127E02
1.385,2.667 1.396,3.156 1.396,3.156 1.635,2.719 true 1.51,2.177 1.24,1.854 1.24,1.854 1.302,2.271 true 0.073,0.031 0.385,0.229 0.313,0.198 10 false *a 1.104,1.677 1.417,1.875 0.313,0.198 10 false *b 1.292,3.188 1.604,3.385 0.313,0.198 10 false *b

Install the No. 2 windshield glass stopper to the windshield glass as shown in the illustration.

Text in Illustration
*a Back Side
*b Ceramic Notch



Hide 56115F 5.INSTALL WINDSHIELD GLASS STOPPER

a.

Using non-residue solvent, clean the windshield glass stopper installation surface of the windshield glass.


b.

Install the glass primer to the windshield glass stopper installation surface of the windshield glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new windshield glass stopper.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.
B474343E01
1.802,2.677 1.646,2.344 1.646,2.344 1.938,2.208 true 2.052,2.656 2.542,2.677 2.542,2.677 2.125,2.271 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.448,2.25 1.635,2.417 0.188,0.167 10 false *b 2.604,2.615 2.792,2.781 0.188,0.167 10 false *b

Install the No. 2 windshield glass stopper to the windshield glass as shown in the illustration.

Text in Illustration
*a Back Side
*b Ceramic Notch


Hide 75535E 6.INSTALL OUTSIDE LOWER WINDSHIELD MOULDING

a.

Using non-residue solvent, clean the outside lower windshield moulding installation surface of the windshield glass.


b.

Install the glass primer to the outside lower windshield moulding installation surface of the windshield glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.




c.

Remove the peeling paper from a new outside lower windshield moulding.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



d.

Install the outside lower windshield moulding to the windshield glass as shown in the illustration.

B474345E01
0.823,0.917 0.677,0.729 false 6.344,0.917 6.51,0.729 false 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.5,0.615 0.729,0.781 0.229,0.167 10 false *b 6.563,0.625 6.792,0.792 0.229,0.167 10 false *b

Text in Illustration
*a Back Side *b R End


Hide 56111 7.INSTALL WINDSHIELD GLASS

a.

Clean and shape the contact surface of the vehicle body.

i.
B455055E01
0.583,1.177 0.583,1.448 false 0.5,1.479 0.813,1.677 0.313,0.198 10 false *a 3.115,0.375 3.26,0.552 0.146,0.177 10 false a

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

Standard:
Area Specified Condition
a 1.0 to 3.0 mm (0.0394 to 0.118 in.)



ii.

Clean the contact surface of the vehicle body with non-residue solvent.

Text in Illustration
*a Vehicle Body
V100155

Adhesive



b.

Position the windshield glass.

i.

Using suction cups, place the windshield glass in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.
B474331E01
1.719,0.521 2.271,0.281 2.271,0.281 1.729,0.854 true 2.302,0.167 2.552,0.344 0.25,0.177 10 true *a

When using a new windshield glass:

Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.

Text in Illustration
*a Matchmarks


iv.

Using suction cups, remove the windshield glass.


v.

Using a brush or sponge, apply body primer to the exposed part of the vehicle body.

NOTICE:
·

Do not apply too much primer.

·

Do not apply primer to the adhesive.

·

When applying the primer, take care of the seams of the panel and spot welds.




vi.

Using a brush or sponge, apply glass primer to the contact surface of the glass.

NOTICE:
·

Do not apply too much primer.

·

Allow the primer to dry for 3 minutes or more.



B474346E01
1.896,0.885 2.052,1.083 0.156,0.198 10 false A 1.896,1.26 2.052,1.458 0.156,0.198 10 false A 0.469,1.385 0.625,1.583 0.156,0.198 10 false B 0.115,1.385 0.271,1.583 0.156,0.198 10 false B 1.906,2.219 2.063,2.417 0.156,0.198 10 false C 1.896,2.604 2.052,2.802 0.156,0.198 10 false C 3.344,2.01 3.5,2.208 0.156,0.198 10 false D 3.448,2.385 3.604,2.583 0.156,0.198 10 false D 0.146,0.125 0.396,0.302 0.25,0.177 10 false *a 3.75,0.156 4.083,0.333 0.333,0.177 10 false A-A 5.5,0.167 5.833,0.344 0.333,0.177 10 false B-B 3.76,1.948 4.094,2.125 0.333,0.177 10 false C-C 5.479,1.948 5.813,2.125 0.333,0.177 10 false D-D 4.438,0.469 4.594,0.667 0.156,0.198 10 false b 4.125,0.719 4.25,0.896 0.125,0.177 10 false a 6.135,1.146 6.26,1.323 0.125,0.177 10 false c 4.323,2.885 4.448,3.063 0.125,0.177 10 false c 5.844,2.323 5.969,2.5 0.125,0.177 10 false e 6.354,2.625 6.479,2.802 0.125,0.177 10 false d

Text in Illustration
*a Back Side - -
V100155

Glass Primer Application Area - -

Standard:
Area Specified Condition
a 7.0 mm (0.276 in.)
b 14 mm (0.551 in.)
c 16.5 mm (0.650 in.)
d 7.8 mm (0.307 in.)
e 22 mm (0.866 in.)




c.

Apply adhesive to the windshield glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or Equivalent



d.
B214800E32
2.479,0.573 2.958,0.406 true 1.198,0.479 1.344,0.604 false 0.563,0.604 0.813,0.844 0.25,0.24 10 false a 1.302,1.406 1.552,1.646 0.25,0.24 10 false a 0.771,1.021 1.021,1.26 0.25,0.24 10 false b 1.115,0.906 1.365,1.146 0.25,0.24 10 false b 2.99,0.292 3.24,0.531 0.25,0.24 10 false *1

Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard:
Area Specified Condition
a 12 mm (0.472 in.)
b 8.0 mm (0.315 in.)


Text in Illustration
*1 Sealer Gun

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.



e.

Load the sealer gun with the cartridge.


f.

Apply adhesive to the glass as shown in the illustration.

NOTICE:

Allow the primer to dry for 3 minutes or more.


B474347E01
4.26,1.375 4.458,1.135 true 6.615,1.042 6.26,0.792 true 4.063,2.823 4.354,2.552 true 5.927,3.156 5.646,3.365 5.646,3.365 5.719,3.167 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.906,0.875 2.083,1.042 0.177,0.167 10 false A 1.906,1.271 2.083,1.438 0.177,0.167 10 false A 0.083,1.396 0.26,1.563 0.177,0.167 10 false B 0.479,1.396 0.656,1.563 0.177,0.167 10 false B 1.906,2.219 2.083,2.385 0.177,0.167 10 false C 1.906,2.604 2.083,2.771 0.177,0.167 10 false C 3.458,2.365 3.635,2.531 0.177,0.167 10 false D 3.333,2.031 3.51,2.198 0.177,0.167 10 false D 3.729,0.146 4.115,0.323 0.385,0.177 10 false A-A 5.458,0.146 5.802,0.302 0.344,0.156 10 false B-B 3.76,1.927 4.146,2.104 0.385,0.177 10 false C-C 5.458,1.927 5.792,2.083 0.333,0.156 10 false D-D 4.229,0.521 4.406,0.688 0.177,0.167 10 false a 6.073,1.167 6.25,1.333 0.177,0.167 10 false b 4.458,2.958 4.635,3.125 0.177,0.167 10 false b 6.229,2.063 6.406,2.229 0.177,0.167 10 false c 5.802,2.396 5.979,2.563 0.177,0.167 10 false d 4.094,1.385 4.302,1.552 0.208,0.167 10 false *b 6.625,1.073 6.833,1.24 0.208,0.167 10 false *b 3.927,2.813 4.135,2.979 0.208,0.167 10 false *b 5.458,3.323 5.667,3.49 0.208,0.167 10 false *b

Text in Illustration
*a Back Side *b Adhesive Center
V100155

Adhesive - -

Standard:
Area Specified Condition
a 14 mm (0.551 in.)
b 9.5 mm (0.374 in.)
c 24.8 mm (0.976 in.)
d 8.0 mm (0.315 in.)



g.

Install the windshield glass to the vehicle body.


h.
B474331E01
1.719,0.521 2.271,0.281 2.271,0.281 1.729,0.854 true 2.302,0.167 2.552,0.344 0.25,0.177 10 true *a

Using suction cups, position the windshield glass so that the matchmarks are aligned.

Text in Illustration
*a Matchmarks


i.

Press it in gently along the rim.

NOTICE:
·

Check that the stoppers are attached to the vehicle body correctly.

·

Check that the vehicle body and glass have a small gap between them.



HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



j.

Using a scraper, remove any excess or protruding adhesive.

NOTICE:

Apply adhesive to the glass rim.



Hide 8.INSPECT FOR LEAKS AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 63310 9.INSTALL ROOF HEADLINING ASSEMBLY

Hide 63812 10.INSTALL NO. 2 ROOF VENTILATOR COVER (w/o Rear Air Duct)

Hide 55905H 11.INSTALL CONTROL KNOB SUB-ASSEMBLY (w/o Rear Air Duct)

Hide 63651B 12.INSTALL AIR INTAKE NET (w/ Rear Air Duct)

Hide 63656D 13.INSTALL CENTER AIR INTAKE COVER (w/ Rear Air Duct)

Hide 87810 14.INSTALL INNER REAR VIEW MIRROR ASSEMBLY

Hide 83910G 15.INSTALL CLOCK ASSEMBLY

Hide 63310A 16.INSTALL ROOF HEADLINING ASSEMBLY HOLE PLUG (w/ Cover)

Hide 74320 17.INSTALL VISOR ASSEMBLY LH (w/ Passenger Side Visor)

Hide 74310 18.INSTALL VISOR ASSEMBLY RH

Hide 63610C 19.INSTALL NO. 1 AIR OUTLET REGISTER ASSEMBLY (w/ Rear Air Duct)

Hide 63371B 20.INSTALL NO. 1 ROOF BOARD SET MOULDING

Hide 63375D 21.INSTALL ROOF HEADLINING MOULDING (w/o Rear Air Duct)

Hide 63375B 22.INSTALL NO. 1 ROOF HEADLINING MOULDING RH (w/o Rear Air Duct)

Hide 65938 23.INSTALL NO. 3 CURTAIN RAIL (w/ Curtain)

Hide 62547B 24.INSTALL NO. 3 PILLAR GARNISH LH

Hide 73220 25.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 1 Seat)

Hide 62212 26.INSTALL FRONT PILLAR GARNISH LH

Hide 62211 27.INSTALL FRONT PILLAR GARNISH RH

Hide 74603 28.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY

Hide 74617V 29.INSTALL ASSIST GRIP PLUG

Hide 63951 30.INSTALL COOLER PIPE COVER

Hide 62413A 31.INSTALL LOWER CENTER PILLAR GARNISH RH

Hide 73210 32.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

Hide 62311C 34.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 58651A 35.INSTALL FRONT NO. 1 DOOR MAT PLATE

Hide 46243 36.INSTALL PARKING BRAKE LEVER COVER

Hide 37.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 38.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85292B 39.INSTALL FRONT WIPER ARM HEAD CAP

Hide 40.INSTALL FRONT PILLAR END COVER RH

Hide 41.INSTALL FRONT PILLAR END COVER LH

Hide 87940 42.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 53181A 45.INSTALL HEADLIGHT COVER RH

HINT:

The procedure listed below is for the LH side.


Hide 63085A 46.INSTALL ROOF VENTILATOR LOUVER SUB-ASSEMBLY RH

Hide 63086A 47.INSTALL ROOF VENTILATOR LOUVER SUB-ASSEMBLY LH

Hide 49.CONNECT BATTERY NEGATIVE TERMINAL