1.REMOVE REAR SEAT ASSEMBLY (for Rear End)
for Tumble Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Tumble Type 4-Passenger Seat)>REMOVAL
for Fixed Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fixed Type 4-Passenger Seat)>REMOVAL
2.REMOVE ROOM RACK ASSEMBLY (w/ Room Rack)
58614A
3.REMOVE NO. 4 MAT SET PLATE
64735A
4.REMOVE CENTER BACK INNER RAIL GARNISH (w/ Lift Up Type)
62471D
5.REMOVE REAR UPPER PILLAR GARNISH RH
62472D
6.REMOVE REAR UPPER PILLAR GARNISH LH
62227
7.REMOVE QUARTER PILLAR COVER RH
62228
8.REMOVE LOWER QUARTER PILLAR COVER LH
62511R
9.REMOVE REAR BODY REAR INSIDE TRIM RH
62512R
10.REMOVE REAR BODY REAR INSIDE TRIM LH
65905B
11.REMOVE WINDOW CURTAIN RAIL SUB-ASSEMBLY (w/ Curtain)
63316A
12.REMOVE NO. 6 ROOF HEADLINING
85192R
13.REMOVE REAR WIPER ARM COVER
14.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY
87950
15.REMOVE OUTER UNDER REAR VIEW MIRROR ASSEMBLY
64810
16.REMOVE BACK WINDOW ASSEMBLY
The back window assembly may fall while performing this procedure. Therefore, use suction cups to hold the back window assembly from the outside of the vehicle.
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
| *1 | Protective Tape |
Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.
Matchmarks do not need to be placed if not reusing the glass.
| *a | Matchmarks |
Install the suction cups to the back window assembly.
From the interior, insert a piano wire between the vehicle body and glass.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
When separating the glass from the vehicle, Do not damage the vehicle paint or interior/exterior ornaments.
| *1 | Piano Wire |
| *2 | Back Window Glass Clip |
| *3 | Back Window Glass Clip LH |
Cut through the adhesive by pulling the piano wire around the glass.
Using suction cups, disconnect the back window glass clip, back window glass clip LH and remove the back window assembly.
Be careful not to drop the back window assembly.
64827D
17.REMOVE BACK WINDOW GLASS CLIP
When reusing the back window assembly:
Using a scraper, remove the back window glass clip.
Do not damage the back window assembly.
Be sure to replace the back window glass clip with a new one.
| *a | Back Side |
64828C
18.REMOVE BACK WINDOW GLASS CLIP LH
When reusing the back window assembly:
Using a scraper, remove the back window glass clip LH.
Do not damage the back window assembly.
Be sure to replace the back window glass clip LH with a new one.
| *a | Back Side |
68299A
19.REMOVE BACK DOOR GLASS SPACER
When reusing the back window assembly:
Using a scraper, remove the 14 back window glass spacers.
Do not damage the back window assembly.
Be sure to replace the back window glass spacer with a new one.
| *a | Back Side |
56114C
20.REMOVE WINDSHIELD GLASS RETAINER
When reusing the back window assembly:
Using a scraper, remove the 4 back window glass retainers.
Do not damage the back window assembly.
Be sure to replace the back window glass retainer with a new one.
| *a | Back Side |
64819A
21.REMOVE NO. 2 BACK WINDOW GLASS SPACER
Using a scraper, remove the 4 No. 2 back window glass spacers.
Do not damage the vehicle body.
Be sure to replace the No. 2 back window glass spacer with a new one.