1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
89910
3.REMOVE COOLER BOX ASSEMBLY (w/ Cooler Box)
4.REMOVE FRONT PROTECTOR ASSEMBLY RH (w/ Protector)
Remove the 6 bolts and front protector assembly RH.
62212
5.REMOVE FRONT PILLAR GARNISH LH
Use the same procedure described for the RH side.
62989
6.REMOVE CENTER DOOR LOCK COVER (for Folding Type)
Detach the 8 clips and remove the center door lock cover.
62425
7.REMOVE CENTER PILLAR GARNISH COVER (w/ Hand Grip Frame)
74730
8.REMOVE HAND GRIP FRAME ASSEMBLY (w/ Hand Grip Frame)
62638A
9.REMOVE QUARTER PILLAR GARNISH RH
for Folding Type:
Detach the 2 claws and 6 clips and remove the quarter pillar garnish RH.
for Glide Type:
Detach the claw and 6 clips and remove the quarter pillar garnish RH.
73224
10.REMOVE FRONT SEAT BELT RETRACTOR COVER LH (w/ Rear No. 1 Seat)
73220
11.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 1 Seat)
Remove the rear seat first row and the second row.
Remove the bolt.
Detach the guide and disconnect the front seat outer belt anchor.
Using a moulding remover D, detach the 2 claws and open the front seat outer belt shoulder anchor cover.
Loosen the bolt and disconnect the shoulder anchor of the front seat outer belt assembly LH.
62547B
12.REMOVE NO. 3 PILLAR GARNISH LH
67676
13.REMOVE FRONT SIDE TRIM BOARD COVER LH
Remove the screw.
Detach the 3 clips and 4 claws and remove the front side trim board cover LH.
62540A
14.REMOVE NO. 2 SIDE TRIM ASSEMBLY LH
Detach the 9 clips and remove the No. 2 side trim assembly LH.
62520G
15.REMOVE NO. 1 SIDE TRIM ASSEMBLY LH
Detach the 13 clips.
Detach the 2 guides and remove the No. 1 side trim assembly LH.
62515B
16.REMOVE NO. 1 SIDE TRIM BASE COVER RH
except Type B:
Detach the 4 claws and clip and remove the No. 1 side trim base cover RH.
for Type B:
Detach the 2 claws and clip and remove the No. 1 side trim base cover RH.
62627D
17.REMOVE SIDE TRIM COVER RH (for Type B)
Detach the 3 claws and remove the side trim cover RH in the direction indicated by the arrows in the illustration.
62516B
18.REMOVE NO. 2 SIDE TRIM BASE COVER RH
Detach the clip and 5 claws and remove the No. 2 side trim base cover RH.
62516D
19.REMOVE NO. 3 SIDE TRIM BASE COVER RH (w/ No. 3 Side Trim Base Cover RH)
Use the same procedure described for the No. 2 side trim base cover RH.
62516E
20.REMOVE NO. 4 SIDE TRIM BASE COVER RH (w/ No. 4 Side Trim Base Cover RH)
except Type B:
Use the same procedure described for the No. 2 side trim base cover RH.
for Type B:
Detach the 3 claws and clip and remove the No. 4 side trim base cover RH.
62516F
21.REMOVE NO. 5 SIDE TRIM BASE COVER RH (w/ No. 5 Side Trim Base Cover RH)
except Type B:
Use the same procedure described for the No. 2 side trim base cover RH.
for Type B:
Detach the 2 claws.
Remove the No. 5 side trim base cover RH in the direction indicated by the arrows in the illustration.
62516G
22.REMOVE NO. 6 SIDE TRIM BASE COVER RH (for Long Body, w/ No. 6 Side Trim Base Cover RH)
Use the same procedure described for the No. 2 side trim base cover RH.
62671F
23.REMOVE NO. 1 SIDE TRIM BOARD COVER RH
Detach the clip and 5 claws and remove the No. 1 side trim board cover RH.
62525D
24.REMOVE NO. 1 SIDE TRIM BASE COVER LH
Use the same procedure described for the No. 1 side trim base cover RH.
62526D
25.REMOVE NO. 2 SIDE TRIM BASE COVER LH
Use the same procedure described for the No. 2 side trim base cover RH.
62526F
26.REMOVE NO. 3 SIDE TRIM BASE COVER LH (w/ No. 3 Side Trim Base Cover LH)
except Type B:
Use the same procedure described for the No. 2 side trim base cover RH.
for Type B:
Use the same procedure described for the No. 4 side trim base cover RH.
62526G
27.REMOVE NO. 4 SIDE TRIM BASE COVER LH (w/ No. 4 Side Trim Base Cover LH)
except Type B:
Use the same procedure described for the No. 2 side trim base cover RH.
for Type B:
Use the same procedure described for the No. 5 side trim base cover RH.
62672
28.REMOVE NO. 1 SIDE TRIM BOARD COVER LH
Use the same procedure described for the No. 1 side trim board cover RH.
29.REMOVE REAR SEAT ASSEMBLY RH
for 2-Passenger Seat with Separate Type Seatback:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 2-Passenger Seat with Separate Type Seatback)>REMOVAL
for 2-Passenger Seat with Bench Type Seatback:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 2-Passenger Seat with Bench Type Seatback)>REMOVAL
30.REMOVE REAR SEAT ASSEMBLY LH
for Single-Passenger Seat with 3 Point Type Seat Belt:
for Single-Passenger Seat without 3 Point Type Seat Belt:
31.REMOVE REAR NO. 8 SEAT ASSEMBLY (for 4-Passenger Seat)
for Tumble Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Tumble Type 4-Passenger Seat)>REMOVAL
for Fixed Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fixed Type 4-Passenger Seat)>REMOVAL
62425
32.REMOVE CENTER PILLAR GARNISH COVER
74730
33.REMOVE HAND GRIP FRAME ASSEMBLY (for Folding Type)
Remove the 7 bolts and hand grip frame assembly.
74708
34.REMOVE NO. 2 HAND GRIP FRAME SUB-ASSEMBLY (for Glide Type)
for Type A:
Remove the 8 bolts and No. 2 hand grip frame sub-assembly.
for Type B:
Remove the 7 bolts and No. 2 hand grip frame sub-assembly.
62639A
35.REMOVE QUARTER PILLAR GARNISH LH
for Folding Type:
Detach the 2 claws and 6 clips and remove the quarter pillar garnish LH.
for Glide Type:
Detach the 3 claws and 6 clips and remove the quarter pillar garnish LH.
62622C
36.REMOVE NO. 2 SIDE TRIM BOARD LH
for Standard Body:
Remove the 2 clips.
Detach the 2 clips and remove the No. 2 side trim board LH.
for Long Body:
Remove the 5 clips.
Detach the 6 clips and remove the No. 2 side trim board LH.
62623C
37.REMOVE NO. 3 SIDE TRIM BOARD LH
Remove the 4 clips.
Detach the 6 clips and remove the No. 3 side trim board LH.
61890A
38.REMOVE BACK WINDOW GLASS HAMMER ASSEMBLY (w/ Hammer)
62548B
39.REMOVE NO. 4 PILLAR GARNISH LH
Detach the 4 claws and 4 clips and remove the No. 4 pillar garnish LH.
62540A
40.REMOVE NO. 2 SIDE TRIM ASSEMBLY LH
Remove the 4 clips.
Detach the 7 clips and remove the No. 2 side trim assembly LH.
62549B
41.REMOVE NO. 5 PILLAR GARNISH LH (for Long Body)
Detach the 4 claws and 4 clips and remove the No. 5 pillar garnish LH.
58614A
42.REMOVE NO. 4 MAT SET PLATE
Remove the 5 screws and No. 4 mat set plate.
64735A
43.REMOVE CENTER BACK INNER RAIL GARNISH (for Lift Up Type)
62487A
44.REMOVE INNER ROOF SIDE GARNISH COVER RH (for Double Swing Out Type)
62488A
45.REMOVE INNER ROOF SIDE GARNISH COVER LH (for Double Swing Out Type)
Use the same procedure described for the RH side.
62471D
46.REMOVE REAR UPPER PILLAR GARNISH RH
62472D
47.REMOVE REAR UPPER PILLAR GARNISH LH
Use the same procedure described for the RH side.
62227
48.REMOVE QUARTER PILLAR COVER RH
Detach the 5 claws and remove the quarter pillar cover RH.
62228
49.REMOVE LOWER QUARTER PILLAR COVER LH
Detach the 4 claws and remove the lower quarter pillar cover LH.
62511R
50.REMOVE REAR BODY REAR INSIDE TRIM RH
for Double Swing Out Type:
Remove the 3 clips.
Detach the 4 clips and remove the rear body rear inside trim RH.
for Lift Up Type:
for Type A:
Remove the 3 clips.
Detach the 4 clips and remove the rear body rear inside trim RH.
for Type B:
Remove the 3 clips.
Detach the 3 clips and remove the rear body rear inside trim RH.
62512R
51.REMOVE REAR BODY REAR INSIDE TRIM LH
for Double Swing Out Type:
Remove the 3 clips.
Detach the 4 clips and remove the rear body rear inside trim LH.
for Lift Up Type:
for Type A:
Remove the 3 clips.
Detach the 4 clips and remove the rear body rear inside trim LH.
for Type B:
Remove the 3 clips.
Detach the 3 clips and remove the rear body rear inside trim LH.
62624C
52.REMOVE NO. 4 SIDE TRIM BOARD LH
for Standard Body:
Detach the 4 clips and remove the No. 4 side trim board LH.
for Long Body:
Detach the 4 clips and remove the No. 4 side trim board LH.
62625C
53.REMOVE NO. 5 SIDE TRIM BOARD LH
Remove the 6 clips.
Detach the 6 clips and remove the No. 5 side trim board LH.
62560B
54.REMOVE NO. 3 SIDE TRIM ASSEMBLY LH
Remove the 4 clips.
Detach the 7 clips and remove the No. 3 side trim assembly LH.
62570C
55.REMOVE NO. 4 SIDE TRIM ASSEMBLY (for Long Body)
Remove the 3 clips.
Detach the 3 clips and remove the No. 4 side trim assembly.
63375D
56.REMOVE ROOF HEADLINING MOULDING (w/o Rear Air Duct)
Use the same procedure described for the RH side.
63378C
57.REMOVE NO. 3 ROOF HEADLINING MOULDING (w/o Rear Air Duct)
Use the same procedure to remove the No. 2 roof headlining moulding.
62452B
58.REMOVE NO. 3 ROOF SIDE RAIL GARNISH LH (w/o Rear Air Duct)
Detach the 6 clips and 2 claws and remove the No. 3 roof side rail garnish LH.
62451E
59.REMOVE REAR ROOF SIDE RAIL GARNISH (w/o Rear Air Duct)
Detach the 7 clips and 2 claws and remove the rear roof side rail garnish.
62452C
60.REMOVE REAR ROOF SIDE RAIL GARNISH LH (w/o Rear Air Duct)
Detach the 7 clips and remove the rear roof side rail garnish LH.
61.REMOVE FRONT SEAT ASSEMBLY
46243
62.REMOVE PARKING BRAKE LEVER COVER
58651A
63.REMOVE FRONT DOOR NO. 1 MAT PLATE
62311C
64.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
73233
65.REMOVE OUTER LAP BELT ANCHOR COVER
73210
66.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
62413A
67.REMOVE LOWER CENTER PILLAR GARNISH RH
63951
68.REMOVE COOLER PIPE COVER
62537B
69.REMOVE NO. 3 PILLAR GARNISH RH
Detach the 4 claws and 4 clips and remove the No. 3 pillar garnish RH.
62538B
70.REMOVE NO. 4 PILLAR GARNISH RH
Detach the 4 claws and 4 clips and remove the No. 4 pillar garnish RH.
62539B
71.REMOVE NO. 5 PILLAR GARNISH RH (for Long Body)
Detach the 4 claws and 4 clips and remove the No. 5 pillar garnish RH.
62615C
72.REMOVE NO. 5 SIDE TRIM BOARD RH
Remove the 6 clips.
Detach the 6 clips and remove the No. 5 side trim board RH.
62614C
73.REMOVE NO. 4 SIDE TRIM BOARD RH
Remove the 2 clips.
Detach the 4 clips and remove the No. 4 side trim board RH.
62613C
74.REMOVE NO. 3 SIDE TRIM BOARD RH
Remove the 4 clips.
Detach the 6 clips and remove the No. 3 side trim board RH.
62612C
75.REMOVE NO. 2 SIDE TRIM BOARD RH
for Standard Body:
Remove the 3 clips.
Detach the 3 clips and remove the No. 2 side trim board RH.
for Long Body:
Remove the 6 clips.
Detach the 7 clips and remove the No. 2 side trim board RH.
62611C
76.REMOVE NO. 1 SIDE TRIM BOARD RH
Remove the 6 clips.
Detach the 6 clips and remove the No. 1 side trim board RH.
62570C
77.REMOVE NO. 4 SIDE TRIM ASSEMBLY (for Long Body)
Remove the 3 clips.
Detach the 3 clips and remove the No. 4 side trim assembly.
62550E
78.REMOVE NO. 3 SIDE TRIM ASSEMBLY RH
Remove the 4 clips.
Detach the 7 clips and remove the No. 3 side trim assembly RH.
62530A
79.REMOVE NO. 2 SIDE TRIM ASSEMBLY RH
Remove the 4 clips.
Detach the 7 clips and remove the No. 2 side trim assembly RH.
62510G
80.REMOVE NO. 1 SIDE TRIM ASSEMBLY RH
Remove the 4 clips.
Detach the 7 clips and remove the No. 1 side trim assembly RH.
63375B
81.REMOVE NO. 1 ROOF HEADLINING MOULDING RH (w/o Rear Air Duct)
63377C
82.REMOVE NO. 2 ROOF HEADLINING MOULDING (w/o Rear Air Duct)
62451B
83.REMOVE NO. 3 ROOF SIDE RAIL GARNISH RH (w/o Rear Air Duct)
Detach the 7 clips and 2 claws and remove the No. 3 roof side rail garnish RH.
62451E
84.REMOVE REAR ROOF SIDE RAIL GARNISH (w/o Rear Air Duct)
Detach the 7 clips and 2 claws and remove the rear roof side rail garnish.
62451C
85.REMOVE REAR ROOF SIDE RAIL GARNISH RH (w/o Rear Air Duct)
Detach the 6 clips and remove the rear roof side rail garnish RH.