Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for RHD vehicles.
1.REMOVE REAR SEAT ASSEMBLY (for Rear End)
for Tumble Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Tumble Type 4-Passenger Seat)>REMOVAL
for Fixed Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fixed Type 4-Passenger Seat)>REMOVAL
2.REMOVE ROOM RACK ASSEMBLY (w/ Room Rack)
63372A
3.REMOVE NO. 2 ROOF BOARD SET MOULDING
63372F
4.REMOVE NO. 3 ROOF BOARD SET MOULDING
63324
5.REMOVE NO. 4 ROOF BOARD
65936
6.REMOVE NO. 1 CURTAIN RAIL (w/ Curtain)
63940
7.REMOVE NO. 4 INNER COOLER DUCT LH
58614A
8.REMOVE NO. 4 MAT SET PLATE
66301D
9.REMOVE ROPE HOOK SUB-ASSEMBLY (for Double Swing Out Type)
65905B
10.REMOVE WINDOW CURTAIN RAIL SUB-ASSEMBLY (for Lift Up Type, w/ Curtain)
64735A
11.REMOVE CENTER BACK RAIL INNER GARNISH (LIFT UP TYPE BACK DOOR)
63349A
12.REMOVE REAR ROOF HEADLINING GARNISH (for Double Swing Out Type)
62487A
13.REMOVE INNER ROOF SIDE GARNISH COVER RH (for Double Swing Out Type)
62488A
14.REMOVE INNER ROOF SIDE GARNISH COVER LH (for Double Swing Out Type)
62471D
15.REMOVE REAR UPPER PILLAR GARNISH RH
62472D
16.REMOVE REAR UPPER PILLAR GARNISH LH
62228
17.REMOVE LOWER QUARTER PILLAR COVER LH
62512R
18.REMOVE REAR BODY REAR INSIDE TRIM LH
63316A
19.REMOVE NO. 6 ROOF HEADLINING
20.REMOVE SIDE PANEL
for RHD:
Perform the linked removal procedures until the No. 4 side trim assembly LH.
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for RHD)>REMOVAL
for LHD:
Perform the linked removal procedures until the No. 4 side trim assembly LH.
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for LHD)>REMOVAL
62740A
21.REMOVE REAR SIDE WINDOW ASSEMBLY LH
The rear side window assembly LH may fall while performing this procedure. Therefore, use suction cups to hold the rear side window assembly LH from the outside of the vehicle.
Apply protective tape to the outer surface of the vehicle body and glass to prevent scratches.
| *1 | Protective Tape |
Install the suction cups to the rear side window assembly LH.
Apply a sufficient amount of soapy water to the adhesive.
Start this procedure where the rear side window assembly LH and body are furthest apart.
From the interior, insert a knife between the vehicle body and glass.
Cut through the adhesive by knife around the glass.
Using suction cups, disconnect the 4 upper quarter window glass retainers and remove the rear side window assembly LH.
Be careful not to drop the rear side window assembly LH.
62785D
22.REMOVE QUARTER WINDOW GLASS SPACER
When reusing the rear side window assembly LH:
Using a scraper, remove the 4 quarter window glass spacers.
Do not damage the rear side window assembly LH.
Be sure to replace the quarter window glass spacer with a new one.
| *a | Back Side |
62763J
23.REMOVE UPPER QUARTER WINDOW GLASS RETAINER
When reusing the rear side window assembly LH:
Using a scraper, remove the 2 upper quarter window glass retainers.
Do not damage the rear side window assembly LH.
Be sure to replace the upper quarter window glass retainer with a new one.
| *a | Back Side |