Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for RHD vehicles.
1.REMOVE REAR SEAT ASSEMBLY (for Rear End)
for Tumble Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Tumble Type 4-Passenger Seat)>REMOVAL
for Fixed Type 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Fixed Type 4-Passenger Seat)>REMOVAL
45619K
2.REMOVE KNUCKLE STOPPER COVER (w/ Room Rack)
3.REMOVE ROOM RACK ASSEMBLY (w/ Room Rack)
63372A
4.REMOVE NO. 2 ROOF BOARD SET MOULDING (w/ Rear Air Duct)
63372F
5.REMOVE NO. 3 ROOF BOARD SET MOULDING (w/ Rear Air Duct)
63324
6.REMOVE NO. 4 ROOF BOARD (w/ Rear Air Duct)
65937
7.REMOVE NO. 2 CURTAIN RAIL (w/ Curtain)
65936
8.REMOVE NO. 1 CURTAIN RAIL (w/ Curtain)
63323
9.REMOVE NO. 3 ROOF BOARD (w/ Rear Air Duct)
63940
10.REMOVE NO. 4 INNER COOLER DUCT LH (for Long Body, w/ Rear Air Duc)
63917A
11.REMOVE NO. 3 INNER COOLER DUCT LH (w/ Rear Air Duct)
63926
12.REMOVE NO. 2 INNER COOLER DUCT LH (w/ Rear Air Duct)
58614A
13.REMOVE NO. 4 MAT SET PLATE
66301D
14.REMOVE ROPE HOOK SUB-ASSEMBLY (w/ Rope Hook)
64735A
15.REMOVE CENTER BACK RAIL INNER GARNISH (for Lift Up Type)
65905B
16.REMOVE WINDOW CURTAIN RAIL SUB-ASSEMBLY (for Lift Up Type, w/ Curtain)
63349A
17.REMOVE REAR ROOF HEADLINING GARNISH (for Double Swing Out Type)
62487A
18.REMOVE INNER ROOF SIDE GARNISH COVER RH (for Double Swing Out Type)
62488A
19.REMOVE INNER ROOF SIDE GARNISH COVER LH (for Double Swing Out Type)
62471D
20.REMOVE REAR UPPER PILLAR GARNISH RH
62472D
21.REMOVE REAR UPPER PILLAR GARNISH LH
62228
22.REMOVE LOWER QUARTER PILLAR COVER LH
62512R
23.REMOVE REAR BODY REAR INSIDE TRIM LH
63316A
24.REMOVE NO. 6 ROOF HEADLINING
25.REMOVE SIDE PANEL
for RHD:
Perform the linked removal procedures until the No. 2 side trim assembly LH.
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for RHD)>REMOVAL
for LHD:
Perform the linked removal procedures until the No. 2 side trim assembly RH.
Click hereVehicle Interior>INTERIOR>SIDE PANEL (for LHD)>REMOVAL
63372A
26.REMOVE NO. 2 ROOF BOARD SET MOULDING (w/o Rear Air Duct)
63377C
27.REMOVE NO. 2 ROOF HEADLINING MOULDING (w/o Rear Air Duct)
63378C
28.REMOVE NO. 3 ROOF HEADLINING MOULDING (w/o Rear Air Duct)
63372G
29.REMOVE NO. 4 ROOF BOARD SET MOULDING (w/o Rear Air Duct)
62452B
30.REMOVE NO. 3 ROOF SIDE RAIL GARNISH LH (w/o Rear Air Duct)
62431F
31.REMOVE ROOF SIDE RAIL GARNISH (for Long Body, w/o Rear Air Duct)
62451E
32.REMOVE REAR ROOF SIDE RAIL GARNISH (w/o Rear Air Duct)
62452C
33.REMOVE REAR ROOF SIDE RAIL GARNISH LH (w/o Rear Air Duct)
34.REMOVE REAR SIDE FRONT WINDOW GLASS LH
The rear side front window glass LH may fall while performing this procedure. Therefore, use suction cups to hold the rear side front window glass LH from the outside of the vehicle.
The rear side front window glass LH is installed with EPT sealer in the area shown in the illustration. Therefore, make sure not to damage it while working.
The rear side front window glass LH may fall while performing this procedure. Therefore, use suction cups to hold the rear side front window glass LH from the outside of the vehicle.
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
| *1 | Protective Tape |
Install the suction cups to the rear side window glass.
Apply a sufficient amount of soapy water to the adhesive.
Start this procedure where the rear side window glass and body are furthest apart.
Cut through the adhesive by knife around the glass.
The rear side front window glass LH is installed with EPT sealer in the area shown in the illustration. Therefore, make sure not to damage it while working.
If the EPT sealer on the rear side front window glass LH is damaged, replace the rear side front window glass LH.
| *A | for Glide Type, Slide Type | *B | for Folding Type, Slide Type |
| *C | for Fixed Type | - | - |
| *1 | EPT sealer | - | - |
| *a | Back Side | - | - |
Using suction cups, disconnect the 4 spacers, and remove the rear side window glass.
Be careful not to drop the rear side window glass.