62720B
1.CLEAN FRONT SIDE WINDOW ASSEMBLY LH
Clean the outer edge of the front side window assembly LH with non-residue solvent.
Do not touch the front side window assembly LH surface after cleaning it.
Do not damage the glass.
Even if using a new front side window assembly LH, clean the front side window assembly LH with non-residue solvent.
62763Q
2.INSTALL SIDE WINDOW FRAME RETAINER
Using non-residue solvent, clean the side window frame retainer installation surface of the vehicle body.
Install the body primer to the side window frame retainer installation surface of the vehicle body.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Location |
Remove the peeling paper from a new side window frame retainer.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the side window frame retainer to the vehicle body as shown in the illustration.
62763W
3.INSTALL SIDE WINDOW FRAME RETAINER
Using non-residue solvent, clean the side window frame retainer installation surface of the front side window assembly LH.
Install the body primer to the side window frame retainer installation surface of the front side window assembly LH.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
Remove the peeling paper from a new side window frame retainer.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the side window frame retainer to the front side window assembly LH as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 2.3 mm (0.0906 in.) |
| *1 | Side Window Frame Retainer |
| *a | Back Side |
| *b | Ceramic Notch |
| *c | Center |
62785W
4.INSTALL SIDE WINDOW GLASS SPACER
Using non-residue solvent, clean the side window glass spacer installation surface of the front side window assembly LH.
Install the glass primer to the side window glass spacer installation surface of the front side window assembly LH.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
Remove the peeling paper from a new side window glass spacer.
After removing the peeling paper, keep the exposed adhesive free from foreign matter.
Install the 4 side window glass spacers to the front side window assembly LH as shown in the illustration.
| *a | Back Side | *b | Ceramic Notch |
62720B
5.INSTALL FRONT SIDE WINDOW ASSEMBLY LH
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 1.0 mm (0.0394 in.) to 3.0 mm (0.118 in.) |
Clean the contact surface of the vehicle body with non-residue solvent.
| *a | Vehicle Body |
|
Adhesive |
Using non-residue solvent, clean the front side window assembly LH installation surface of the vehicle body.
Install the body primer to the front side window assembly LH installation surface of the vehicle body.
Do not apply too much primer.
Do not apply primer to the adhesive.
When applying the primer, take care of the seams of the panel and spot
Install the suction cups to the front side window assembly LH.
Using a brush or sponge, apply glass primer to the contact surface of the front side window assembly LH.
Do not apply too much primer.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | - | - |
|
Glass Primer Application Area | - | - |
Apply adhesive to the front side window assembly LH.
Toyota Genuine Windshield Glass Adhesive or Equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| *1 | Sealer Gun |
Apply adhesive to the front side window assembly LH as shown in the illustration.
Allow the primer to dry for 3 minutes or more.
| *a | Back Side | *b | Adhesive Center |
|
Adhesive | - | - |
Install the front side window assembly LH to the vehicle body.
Using suction cups, attach the 4 side window glass spacers and side window frame retainer and install the front side window assembly LH.
Press it in gently along the rim.
Check that the side window glass spacers, retainers are attached to the vehicle body correctly.
Check that the vehicle body and glass have a small gap between them.
Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive to the glass rim.
6.INSPECT FOR LEAKS AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
62639A
7.INSTALL QUARTER PILLAR GARNISH LH
74708
8.INSTALL NO. 2 HAND GRIP FRAME SUB-ASSEMBLY (for Glide Type)
74730
9.INSTALL HAND GRIP FRAME ASSEMBLY (for Folding Type)
62425
10.INSTALL CENTER PILLAR GARNISH COVER
62520G
11.INSTALL NO. 1 SIDE TRIM ASSEMBLY LH
62540A
12.INSTALL NO. 2 SIDE TRIM ASSEMBLY LH
67676
13.INSTALL FRONT SIDE TRIM BOARD COVER LH
73224
14.INSTALL FRONT SEAT BELT RETRACTOR COVER LH (w/ Rear No. 1 Seat)
62638A
15.INSTALL QUARTER PILLAR GARNISH RH
62989
16.INSTALL CENTER DOOR LOCK COVER (for Folding Type)
63925
17.INSTALL NO. 1 COOLER INNER DUCT LH (w/ Rear Air Duct)
63926
18.INSTALL NO. 2 COOLER INNER DUCT LH (w/ Rear Air Duct)
63917A
19.INSTALL NO. 3 COOLER INNER DUCT LH (w/ Rear Air Duct)
63940
20.INSTALL NO. 4 COOLER INNER DUCT LH (for Long Body, w/ Rear Air Duct)
65938
21.INSTALL NO. 3 CURTAIN RAIL (w/ Curtain)
65936
22.INSTALL NO. 1 CURTAIN RAIL (w/ Curtain)
63310
23.INSTALL ROOF HEADLINING ASSEMBLY