Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1413  Front Speed Sensor RH Output Malfunction  C1414  Front Speed Sensor LH Output Malfunction  


DESCRIPTION

Refer to DTCs C1401 and C1402 (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1401).

DTC No. DTC Detection Condition Trouble Area
C1413
C1414
Either of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor RH/LH

·

Front skid control rotor RH/LH

·

Sensor installation



HINT:
·

DTC C1413 is for the front speed sensor RH.

·

DTC C1414 is for the front speed sensor LH.



PROCEDURE

1.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

According to the display on the GTS, display the Data List, perform a driving test based on the conditions when the problem occurred (determined from the freeze frame data or customer problem analysis results) and check the Data List when the vehicle is running and stopped (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FR Speed Open Momentary interruption of front speed sensor RH pulse input to ECU / Error or Normal Normal Error: Momentary interruption
FL Speed Open Momentary interruption of front speed sensor LH pulse input to ECU / Error or Normal Normal Error: Momentary interruption

OK:

Output value does not change and no interruptions occur according to vehicle speed


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK FRONT SPEED SENSOR INSTALLATION
2.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336E26
0.698,0.385 1.01,0.583 0.313,0.198 10 false *a 2.292,0.385 2.604,0.583 0.313,0.198 10 false *b 2.01,1.656 2.323,1.854 0.313,0.198 10 false *c

Check the front speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.


Text in Illustration
*a Normal
*b Abnormal
*c Clearance


Result:
Proceed to
OK
NG



OK

3.INSPECT FRONT SPEED SENSOR (Foreign Matter Adhesion)

NG

3.INSPECT FRONT SPEED SENSOR (Foreign Matter Adhesion)
a.

Remove the wheel speed sensor corresponding to the DTC and check that the tip is free from oil and foreign matter.

OK:

There is no oil or foreign matter


NOTICE:

This DTC may be detected if foreign matter 1 mm (0.03937 in.) x 1 mm (0.03937 in.) or larger is attached.



Result:
Proceed to
OK
NG



OK

4.INSPECT FRONT SKID CONTROL ROTOR (Foreign Matter Adhesion)

NG

7.CLEAN FRONT SPEED SENSOR
4.INSPECT FRONT SKID CONTROL ROTOR (Foreign Matter Adhesion)
a.

Check that there are no foreign objects or oil on the skid control rotor that was indicated by the DTC.

OK:

There is no oil or foreign matter


HINT:

This DTC may be detected if foreign matter 1 mm (0.03937 in.) x 1 mm (0.03937 in.) or larger is attached.



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SPEED SENSOR AND FRONT SKID CONTROL ROTOR

NG

5.CLEAN FRONT SKID CONTROL ROTOR
5.CLEAN FRONT SKID CONTROL ROTOR
a.

Clean the front skid control rotor.

NOTICE:

Do not use a cleaner to clean the front skid control rotor.



Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (FRONT SPEED SENSOR)
6.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

According to the display on the GTS, display the Data List, perform a driving test based on the conditions when the problem occurred (determined from the freeze frame data or customer problem analysis results) and check the Data List when the vehicle is running and stopped (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FR Speed Open Momentary interruption of front speed sensor RH pulse input to ECU / Error or Normal Normal Error: Momentary interruption
FL Speed Open Momentary interruption of front speed sensor LH pulse input to ECU / Error or Normal Normal Error: Momentary interruption

OK:

Output value does not change and no interruptions occur according to vehicle speed


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE FRONT SPEED SENSOR AND FRONT SKID CONTROL ROTOR

7.CLEAN FRONT SPEED SENSOR
a.

Clean the front speed sensor.

NOTICE:

When cleaning the front speed sensor, clean the sensor mounting hole before installing the sensor.



Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (FRONT SPEED SENSOR)
8.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

According to the display on the GTS, display the Data List, perform a driving test based on the conditions when the problem occurred (determined from the freeze frame data or customer problem analysis results) and check the Data List when the vehicle is running and stopped (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FR Speed Open Momentary interruption of front speed sensor RH pulse input to ECU / Error or Normal Normal Error: Momentary interruption
FL Speed Open Momentary interruption of front speed sensor LH pulse input to ECU / Error or Normal Normal Error: Momentary interruption

OK:

Output value does not change and no interruptions occur according to vehicle speed


NOTICE:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

END

NG

4.INSPECT FRONT SKID CONTROL ROTOR (Foreign Matter Adhesion)